Sometimes the firmware sends a dummy packet event while we are in PLT
mode.  This doesn't make sense, it's a firmware bug.  Fix this by
ignoring dummy packet events when we're PLT mode.
Reported-by: NYegor Yefremov <yegorslists@googlemail.com>
Reported-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NLuciano Coelho <luca@coelho.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the current code is directly setting skb->len, which is not correct and
brings problems with HAVE_EFFICIENT_UNALIGNED_ACCESS enabled in config
Signed-off-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sparse warns about invalid assignment in
drivers/net/wireless/ti/wl1251/cmd.c:451:42: warning: invalid assignment: |=
drivers/net/wireless/ti/wl1251/cmd.c:451:42:    left side has type restricted __le16
drivers/net/wireless/ti/wl1251/cmd.c:451:42:    right side has type int
Hence type converted right side to __le16.
Signed-off-by: NSurendra Patil <surendra.tux@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

the current code is directly setting skb->len, which is not correct and
brings problems with HAVE_EFFICIENT_UNALIGNED_ACCESS enabled in config
Signed-off-by: NIvaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of an explicit cast, use the min_t macro.
Signed-off-by: NSilvan Jegen <s.jegen@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add device tree support for the spi variant of wl1251.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds support for requesting the regulator powering
the vio pin.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the power GPIO handling from the board code into
the driver. This is a dependency for device tree support.
Signed-off-by: NSebastian Reichel <sre@debian.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move the wl1251 part of the wl12xx platform data structure into a new
structure specifically for wl1251.  Change the platform data built-in
block and board files accordingly.
Signed-off-by: NLuciano Coelho <coelho@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Reviewed-by: NSebastian Reichel <sre@debian.org>
Reviewed-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to solve races with sched_scan_stop, it is necessary
for the driver to be able to return an error to propagate that
to cfg80211 so it doesn't send an event.
Reviewed-by: NAlexander Bondar <alexander.bondar@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

TI wl12xx/wl18xx cards support channel switch via a driver specific
switch_channel op while operating with channel contexts.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Enabling beacon filtering before receving a beacon
might result in not having a beacon at all for the
current connected AP, which prevents the station
from entering power-save.

Replace the current approach (of starting beacon
filtering on init) and configure beacon filering
only after bss_conf->dtimper is set (which means
mac80211 already parsed a beacon).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

dfs configuration command might take longer than
the current timeout. increase it to 5 seconds.
Signed-off-by: NYaniv Machani <yanivma@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Silently ignore repetitive scheduling of recovery work and commands
being passed to the bus when the HW is not available. This can happen
many times during recovery and slow it down. It also spams the kernel
logs.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each AP has its own global and broadcast links, so when
checking for active sta count (according to the active_link_count)
we must take them all into account.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mac80211 unsets the default wep key on disassoc.
The fw doesn't support this notification, so simply
ignore it.

The actual flow actually triggers fw recovery in some
cases, as mac80211 unsets the default key only after
disassoc, when wlvif->sta.hlid, resulting in invalid
hlid being passed to the fw.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

12xx chips allow only OFDM rates in AP mode for BT-Coex purposes. This
is no longer required in 18xx chips, starting with FW 8.6.0.0.8.

Update the min allowed FW version in 18xx to support this functionality.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Stopping sched scan on interface removal (during recovery)
is no longer needed, as sched scanning is automatically
restarted by mac80211.
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Send EAPOL frames with voice priority by setting (the new)
TX_HW_ATTR_EAPOL_FRAME bit in tx attribute.

Sending EAPOL with voice priority fixes re-key
timeout issues during heavy traffic.
Signed-off-by: NIgal Chernobelsky <igalc@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Bump the min wl18xx fw version to 8.8.0.0.13

This fw is not backward compatible with older
firmware (due to api changes), so use bump
the firmware name as well.

Some modifications were done to the driver-fw api
in order to support multiple APs.

Additionally, some of the consts (such as max stations,
max links and max RX BA sessions) were changed.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each hw supports a different iface combinations.
Define the supported combinations in each driver,
and save it in wl->iface_combinations.

Since each driver defines its own combinations now,
it can also define its max supported channels, so
we no longer need to save and set it explicitly
in wlcore.

Update wl18xx interface combinations to allow
multiple APs.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Each hw supports a different max stations (connected to the
same ap). add a new wl->max_ap_stations and use it instead
of the current common AP_MAX_STATIONS.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Upcoming fw versions will have different max links support
(according to the hw). Get ready for it by configuring
wl->num_links per-hw, instead of using the const WL12XX_MAX_LINKS.

However, continue using WLCORE_MAX_LINKS in order to simplify
structs declarations (we use it in multiple bitmaps, and converting
them to dynamic arrays is just cumbersome).
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of splitting the fw_status into 2 and using some
complex calculations, read the fw status and let each low-level
driver (wl12xx/wl18xx) convert it into a common struct.

This is required for the upcoming fw api changes, which
break the current logic anyway.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It seems the wl18xx FW sometimes sends spurious changes on the PSM state
of the broadcast HLID. This causes us to search for a station on a
non-peer link and fail, causing warnings in our log.

Prevent the driver from considering PSM changes for any non-peer HLIDs.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the chip is in ELP mode read/write to FW is invalid and may cause
the lower layers to get stuck. The reads/writes concerning ELP wakeup
are the exception here and are checked for. In addition to blocking the
IO, produce a warning.
Signed-off-by: NBarak Bercovitz <barak@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes a tx_flush during suspend fails, but the FW manages to flush
out the packets during the time when the host is supsended. Cancel
the Tx-watchdog on suspend to not cause a spurious recovery on resume
for that case. Set a flag to reinit the watchdog on the first Tx after
resume, so we'll still recover if the FW is not empty and there's
indeed a problem.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

zero rx_filter_enabled array after recovery to avoid
cases were the driver will keep trying to clear a
filter which is not configured in FW.

Such case will cause consecutive recoveries due to
command execution failures.

While on it, convert rx_filter_enabled to bitmap,
to save some memory and make sparse happy (it
doesn't like sizeof(bool array)).
Signed-off-by: NNadim Zubidat <nadimz@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver ignores BSS_CHANGED_TXPOWER changes.
Fix this by calling ACX_TX_POWER when appropriate.
Signed-off-by: NAlex Gal <a.gal@motsai.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

wl1251: fix NULL pointer dereference
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Reported-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add nvs file name to module firmware list
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The firmware doesn't support per packet encryption selection, so disable hw
encryption support completely while a monitor interface is present to support
injection of packets (which shouldn't get encrypted by hw).
To enforce the changed hw encryption support force a disassociation on
non-monitor interfaces.
For disassociation a workaround using hw connection monitor is employed,
which temporary enables hw connection manager flag.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Set the retry limit to 0 and disable the ACK policy for injected packets.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If necessary enable the tx path in monitor mode for packet injection using
the JOIN command with BSS_TYPE_STA_BSS and zero BSSID.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use the ENABLE_RX command for channel switching when no interface is present
(monitor mode only).
The advantage of ENABLE_RX is that it leaves the tx data path disabled in
firmware, whereas the usual JOIN command seems to transmit some frames at
firmware level.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Force power saving off while monitor interface is present.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Port multicast address filtering from wl1271 driver.
It sets up the hardware multicast address filter in configure_filter() with
addresses supplied through prepare_multicast().
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Disable hardware encryption (DF_ENCRYPTION_DISABLE) and decryption
(DF_SNIFF_MODE_ENABLE) via wl1251_acx_feature_cfg while monitor interface is
present.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Split up data path initialisation into RX and TX data path initialisation
functions. This change is required for channel switching in monitor mode.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update hardware ARP filter configuration on BSS_CHANGED_ARP_FILTER
notification from mac80211.
Ported from wl1271 driver.
Signed-off-by: NDavid Gnedt <david.gnedt@davizone.at>
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NPavel Machek <pavel@ucw.cz>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>