With CONFIG_DYNAMIC_DEBUG if dyndbg enables debug output in
8250_port.c deadlock happens inevitably on UART IRQ handling.

That's the problematic execution path:
---------------------------->8------------------------
UART IRQ:
  serial8250_interrupt() ->
    serial8250_handle_irq(): lock "port->lock" ->
      pr_debug() ->
        serial8250_console_write(): bump in locked "port->lock".

      OR (if above pr_debug() gets removed):
      serial8250_tx_chars() ->
        pr_debug() ->
          serial8250_console_write(): bump in locked "port->lock".
---------------------------->8------------------------

So let's get rid of those not that much useful debug entries.

Discussed problem could be easily reproduced with QEMU for x86_64.
As well as this fix could be mimicked with muting of dynamic debug for
the problematic lines as simple as:
---------------------------->8------------------------
dyndbg="+p; file 8250_port.c line 1756 -p; file 8250_port.c line 1822 -p"
---------------------------->8------------------------
Signed-off-by: NAlexey Brodkin <abrodkin@synopsys.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Phillip Raffeck <phillip.raffeck@fau.de>
Cc: Anton Wuerfel <anton.wuerfel@fau.de>
Cc: "Matwey V. Kornilov" <matwey@sai.msu.ru>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Thor Thayer <tthayer@opensource.altera.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

'request_irq()' and 'free_irq()' should be called with the same dev_id.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to Documentation/devicetree/bindings/serial/serial.txt the
generic 'rts-gpios' property can be used to specify the GPIO for RTS
functionality.

Currently it is not possible to use the imx UART port in rs485 mode when
the 'rts-gpios' property is passed in the device tree.

The imx uart driver only checks for the presence of the built-in RTS pin,
via 'uart-has-rtscts' property and disable the rs485 flag if this property
is absent.

So fix this logic by also checking if RTS pin has been passed via GPIO.

Tested on a imx6dl based board.
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Tested-by: NClemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a follow up to the commit a9b01b58 ("serial: 8250_mid fix calltrace
when hotplug 8250 serial controller") in which the kernel crash was described
for another 8250 based driver. It appears that we have the very same issue in
8250_lpss. Fix it by unregistering serial driver first.

Cc: Liwei Song <liwei.song@windriver.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: NBryan O'Donoghue <pure.logic@nexus-software.ie>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.

Export the module alias information using the MODULE_DEVICE_TABLE() macro.

Before this patch:

$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
$

After this patch:

$ modinfo drivers/tty/serial/msm_serial.ko | grep alias
alias:          of:N*T*Cqcom,msm-uartdmC*
alias:          of:N*T*Cqcom,msm-uartdm
alias:          of:N*T*Cqcom,msm-uartC*
alias:          of:N*T*Cqcom,msm-uart
Signed-off-by: NJavier Martinez Canillas <javier@osg.samsung.com>
Acked-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When struct moxa8250_board is allocated, then num_ports should
be initialized in order to use it later in moxa8250_remove.
Signed-off-by: NMatwey V. Kornilov <matwey@sai.msu.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add resource type check for Fintek F81504/508/512, BAR3/4/5 must be
IORESOURCE_IO.

Fintek is trying to make F81504/508/512 works on MMIO interface, but
it's still in progress. We found some issue when the experiment IC
when the BAR3/4/5 is IORESOURCE_MEM. It'll cause wrong operation with
IO resource. So we'll add the resource check for this.
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch updates my email address as I no longer have access to the old
one.
Signed-off-by: NJohn Crispin <john@phrozen.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows enabling earlycon for devices with a Lantiq serial console
by splitting lqasc_serial_port_write() from lqasc_console_write() and
re-using the new function for earlycon's write callback.

The kernel-parameter name matches the driver name ("lantiq"), similar
to how other drivers implement this.
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

'request_irq' and 'free_irq' should have the same 'dev_id'.
Here one uses 'port', and the other one uses 'sport'.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

dma_request_slave_channel_compat() requires filter function and mask, which
are not needed on device tree based platforms, so simplify the code by
calling the more appropriate dma_request_chan() function. This additionally
gives us proper error handling, because the new function returns error
codes instead of NULL on failure.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If CMSPAR is set in the c_cflag of termios, "stick" parity is enabled.

Tested on an i.MX28 system
Signed-off-by: NWolfgang Ocker <weo@reccoware.de>
Acked-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

New IC MAX14830 has 0xB4 silicon revision ID.
This patch adds support for such ICs.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Problem found via lockdep:

- lpuart_set_termios() calls del_timer_sync(&sport->lpuart_timer) while
  holding sport->port.lock

- sport->lpuart_timer routine is lpuart_timer_func() that calls
  lpuart_copy_rx_to_tty() that acquires same lock.

To fix, move Rx DMA stopping out of lock, as it already is in other places
in the same file.

While at it, also make Rx DMA start/stop code to look the same is in
other places in the same file.
Signed-off-by: NNikita Yushchenko <nikita.yoush@cogentembedded.com>
Tested-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the call to kasprintf() returns a NULL pointer, function
sci_request_irq() frees the preallocated memory and returns 0 is
returned. Because 0 means no error, the caller of sci_request_irq()
will keep going, and the freed memory may be used or freed again. To
avoid the above issue, this patch assigns "-ENOMEM" to the return
variable ret.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=188691Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.
Requested-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix the following Calltrace:
[   77.768221] WARNING: CPU: 5 PID: 645 at drivers/dma/dmaengine.c:1069 dma_async_device_unregister+0xe2/0xf0
[   77.775058] dma_async_device_unregister called while 1 clients hold a reference
[   77.825048] CPU: 5 PID: 645 Comm: sh Not tainted 4.8.8-WR9.0.0.0_standard+ #3
[   77.832550] Hardware name: Intel Corp. Aspen Cove/Server, BIOS HAVLCRB1.X64.0012.D58.1604140405 04/14/2016
[   77.840396]  0000000000000000 ffffc90008adbc80 ffffffff81403456 ffffc90008adbcd0
[   77.848245]  0000000000000000 ffffc90008adbcc0 ffffffff8105e2e1 0000042d08adbf20
[   77.855934]  ffff88046a861c18 ffff88046a85c420 ffffffff820d4200 ffff88046ae92318
[   77.863601] Call Trace:
[   77.871113]  [<ffffffff81403456>] dump_stack+0x4f/0x69
[   77.878655]  [<ffffffff8105e2e1>] __warn+0xd1/0xf0
[   77.886102]  [<ffffffff8105e34f>] warn_slowpath_fmt+0x4f/0x60
[   77.893508]  [<ffffffff814187a9>] ? find_next_bit+0x19/0x20
[   77.900730]  [<ffffffff814bf83e>] ? dma_channel_rebalance+0x23e/0x270
[   77.907814]  [<ffffffff814bfee2>] dma_async_device_unregister+0xe2/0xf0
[   77.914992]  [<ffffffff814c53aa>] hsu_dma_remove+0x1a/0x60
[   77.921977]  [<ffffffff814ee14c>] dnv_exit+0x1c/0x20
[   77.928752]  [<ffffffff814edff6>] mid8250_remove+0x26/0x40
[   77.935607]  [<ffffffff8144f1b9>] pci_device_remove+0x39/0xc0
[   77.942292]  [<ffffffff8160cfea>] __device_release_driver+0x9a/0x140
[   77.948836]  [<ffffffff8160d0b3>] device_release_driver+0x23/0x30
[   77.955364]  [<ffffffff81447dcc>] pci_stop_bus_device+0x8c/0xa0
[   77.961769]  [<ffffffff81447f0a>] pci_stop_and_remove_bus_device_locked+0x1a/0x30
[   77.968113]  [<ffffffff81450d4e>] remove_store+0x5e/0x70
[   77.974267]  [<ffffffff81607ed8>] dev_attr_store+0x18/0x30
[   77.980243]  [<ffffffff8123006a>] sysfs_kf_write+0x3a/0x50
[   77.986180]  [<ffffffff8122f5ab>] kernfs_fop_write+0x10b/0x190
[   77.992118]  [<ffffffff811bf1c8>] __vfs_write+0x18/0x40
[   77.998032]  [<ffffffff811bfdee>] vfs_write+0xae/0x190
[   78.003747]  [<ffffffff811c1016>] SyS_write+0x46/0xb0
[   78.009234]  [<ffffffff81a4c31b>] entry_SYSCALL_64_fastpath+0x13/0x8f
[   78.014809] ---[ end trace 0c36dd73b7408eb2 ]---

This happens when the 8250 serial controller is hotplugged as follows:
echo 1 > /sys/bus/pci/devices/0000:00:1a.0/remove

This trace happens due to the serial port still holding a reference when
the dma device is unregistered.
The dma unregister routine will check if there is still a reference exist,
if so it will give the WARNING(here serial port still was not unregister).

To fix this, We need to unregister the serial port first, then do DMA
device unregister to make sure there is no reference when to DMA routine.
Signed-off-by: NLiwei Song <liwei.song@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several versions of DW DMAC have multi block transfers hardware
support. Hardware support of multi block transfers is disabled
by default if we use DT to configure DMAC and software emulation
of multi block transfers used instead.
Add multi-block property, so it is possible to enable hardware
multi block transfers (if present) via DT.

Switch from per device is_nollp variable to multi_block array
to be able enable/disable multi block transfers separately per
channel.
Acked-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NEugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

When running certain workload on a debug kernel with lockdep turned on,
a ppc64 kvm guest could sometimes hit the following lockdep warning:

  [ INFO: possible circular locking dependency detected ]
  Possible unsafe locking scenario:

        CPU0                    CPU1
        ----                    ----
   lock(&mm->mmap_sem);
                                lock(console_lock);
                                lock(&mm->mmap_sem);
   lock(cpu_hotplug.lock);

  *** DEADLOCK ***

Looking at the console code, the console_lock-->mmap_sem scenario will
only happen when reading or writing the console unicode map leading to
a page fault.

To break this circular locking dependency, all the userspace I/O
operations in consolemap.c are now moved outside of the console_lock
critical sections so that the mmap_sem won't be acquired when holding
the console_lock.
Signed-off-by: NWaiman Long <longman@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Testing with a gcc-7 snapshot produced an internal compiler error
for this file:

drivers/tty/nozomi.c: In function 'receive_flow_control':
drivers/tty/nozomi.c:919:12: internal compiler error: in get_substring_ranges_for_loc, at input.c:1388
 static int receive_flow_control(struct nozomi *dc)

I've reported this at https://gcc.gnu.org/bugzilla/show_bug.cgi?id=78569
but also noticed that the code line contains a stack overflow, as it prints
a string into a slightly shorter fixed-length 'tmp' variable.

A lot of the code here is unnecessary and can be expressed in a simpler
way, relying on the fact that removing the 'DEBUG' macro will also get
rid of all pr_debug() calls. This change should not change any of the
output but avoids both the stack overflow and the gcc crash.

The stack overflow will not happen unless a module load parameter is
also set to enable the debug messages.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During a PCI error recovery, like the ones provoked by EEH in the ppc64
platform, all IO to the device must be blocked while the recovery is
completed.  Current 8250_pci implementation only suspends the port
instead of detaching it, which doesn't prevent incoming accesses like
TIOCMGET and TIOCMSET calls from reaching the device.  Those end up
racing with the EEH recovery, crashing it.  Similar races were also
observed when opening the device and when shutting it down during
recovery.

This patch implements a more robust IO blockage for the 8250_pci
recovery by unregistering the port at the beginning of the procedure and
re-adding it afterwards.  Since the port is detached from the uart
layer, we can be sure that no request will make through to the device
during recovery.  This is similar to the solution used by the JSM serial
driver.

I thank Peter Hurley <peter@hurleysoftware.com> for valuable input on
this one over one year ago.
Signed-off-by: NGabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is no need to check port for NULL in uart_port_deref() since we call it
only when port is defined.

There are few places that violate this. Fix them here as well.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The mxs-auart driver does not count FIFO overrun errors. These errors never
appear in /proc/tty/driver/ttyAPP. This is because the OERR status bit is
masked by read_status_mask in the rx interrupt function, but the
AUART_STAT_OERR bit is never set in read_status_mask. The patch enables the
counting of overrun errors.
Signed-off-by: NWolfgang Ocker <weo@reccoware.de>
Reviewed-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add a set_ldisc function to enable/disable IrDA SIR mode according to
the new line discipline, if IrDA SIR mode is supported by the hardware
configuration.
Signed-off-by: NEd Blake <ed.blake@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Expose set_ldisc() function so that it can be overridden with a
platform specific implementation.
Signed-off-by: NEd Blake <ed.blake@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add an IrDA UART capability flag and change the type of
uart_8250_port.capabilities to be u32 rather than unsigned short to
accommodate the additional flag.
Signed-off-by: NEd Blake <ed.blake@imgtec.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When any 8250 based driver sets up DMA and has UART_CAP_RPM capability enabled
the device is left powered on after transfer is done. We need to schedule a
device suspend operation when DMA completes the transfer.

The patch is based on the work done by the reporter.
Reported-by: NHuiquan Zhong <huiquan.zhong@intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following fix of runtime PM use in DMA mode requires at least
serial8250_rpm_put_tx() to be available. Export both calls.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When su_probe() fails it doesn't free *up and we may have a memory
leak. Fix this by freeing *up before return.
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In each call to hv_remove(), con_read_page and con_write_page is not
getting freed and lead to memory leakage. Fix this by freeing both
pointers in hv_remove().
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a disagreement between drivers/tty/vt/keyboard.c and
drivers/input/input-leds.c with regard to what is a Scroll Lock LED
trigger name: input calls it "kbd-scrolllock", but vt calls it
"kbd-scrollock" (two l's).
This prevents Scroll Lock LED trigger from binding to this LED by default.

Since it is a scroLL Lock LED, this interface was introduced only about a
year ago and in an Internet search people seem to reference this trigger
only to set it to this LED let's simply rename it to "kbd-scrolllock".

Also, it looks like this was supposed to be changed before this code was
merged: https://lkml.org/lkml/2015/6/9/697 but it was done only on
the input side.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: NSamuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable <stable@vger.kernel.org> # 4.2+
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fixed typo in comments in drivers/tty/vt/keyboard.c
Signed-off-by: NAskar Safin <safinaskar@mail.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Declare an OF early console for SBSA UART so that the early console device
can be specified via the "stdout-path" property in device-tree.

Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NKefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use DEVICE_ATTR_RO for read only attributes.  This simplifies the
source code, improves readbility, and reduces the chance of
inconsistencies.

The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@ro@
declarer name DEVICE_ATTR;
identifier x,x_show;
@@

DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);

@script:ocaml@
x << ro.x;
x_show << ro.x_show;
@@

if not (x^"_show" = x_show) then Coccilib.include_match false

@@
declarer name DEVICE_ATTR_RO;
identifier ro.x,ro.x_show;
@@

- DEVICE_ATTR(x, \(0444\|S_IRUGO\), x_show, NULL);
+ DEVICE_ATTR_RO(x);
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The STM32 serial port is SoC specific so no point enabling it
without the architecture enabled.
Signed-off-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When spi_setup() fails it doesn't free ifx_dev and we have a memory
leak. Fix this by freeing ifx_dev before the return.
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Inside ioc4_attach_local() 4 memory was allocated using kzalloc and
assign it to ports[] within loop. When kzalloc fails inside loop,
it returns error without freeing previously allocated memory and we
may have memory leak. Fix this by freeing ports[] before return.
Signed-off-by: NSouptick joarder <jrdr.linux@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The fresh new serial driver for pxa produces warnings when
CONFIG_PM_SLEEP is disabled:

drivers/tty/serial/8250/8250_pxa.c:50:12: error: 'serial_pxa_resume' defined but not used [-Werror=unused-function]
drivers/tty/serial/8250/8250_pxa.c:41:12: error: 'serial_pxa_suspend' defined but not used [-Werror=unused-function]

This removes the #ifdef around the two functions and instead marks both
as __maybe_unused, which is more robust and avoids the warning.

Fixes: ab28f51c ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

An otherwise very nice cleanup of the pxa2xx uart support marked the
init function of this driver as __deprecated:

drivers/tty/serial/pxa.c:944:1: error: 'serial_pxa_init' is deprecated [-Werror=deprecated-declarations]

This seems unhelpful to me, as we now warn for every allmodconfig build,
which is otherwise free of warnings on most architectures. Let's
remove the annotation again.

Fixes: ab28f51c ("serial: rewrite pxa2xx-uart to use 8250_core")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop invalid user-pointer check from TIOCGSERIAL handler.

A NULL-pointer can be valid in user space and copy_to_user() takes care
of sanity checking.

Cc: Mikael Starvik <starvik@axis.com>
Cc: linux-cris-kernel@axis.com
Signed-off-by: NJohan Hovold <johan@kernel.org>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>