The recent comment:
commit 7e83ccbe
    md/raid10: Allow skipping recovery when clean arrays are assembled

Causes raid10 to skip a recovery in certain cases where it is safe to
do so.  Unfortunately it also causes a reshape to be skipped which is
never safe.  The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).

Bug was introduced in 3.10, so this is suitable for 3.10-stable.

Cc: stable@vger.kernel.org (3.10)
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NNeilBrown <neilb@suse.de>

There is a bug in 'check_reshape' for raid5.c  To checks
that the new minimum number of devices is large enough (which is
good), but it does so also after the reshape has started (bad).

This is bad because
 - the calculation is now wrong as mddev->raid_disks has changed
   already, and
 - it is pointless because it is now too late to stop.

So only perform that test when reshape has not been committed to.
Signed-off-by: NNeilBrown <neilb@suse.de>

Power-up timing

The DS2408 is sensitive to the power-on slew rate and can inadvertently
power up with a test mode feature enabled.  When this occurs, the P0 port
does not respond to the Channel Access Write command.  For most reliable
operation, it is recommended to disable the test mode after every power-on
reset using the Disable Test Mode sequence shown below.  The 64-bit ROM
code must be transmitted in the same bit sequence as with the Match ROM
command, i.e., least significant bit first.  This precaution is
recommended in parasite power mode (VCC pin connected to GND) as well as
with VCC power.

Disable Test Mode:
RST,PD,96h,<64-bit DS2408 ROM Code>,3Ch,RST,PD

[akpm@linux-foundation.org: don't use kerenldoc token to introduce a non-kerneldoc comment, tweak whitespace]
Signed-off-by: NJean-Francois Dagenais <jeff.dagenais@gmail.com>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use module_pci_driver instead of init/exit, make code clean.
Signed-off-by: NLibo Chen <libo.chen@huawei.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Instead of allocating a struct pps_gpio_platform_data in the DT case,
store the necessary information in struct pps_gpio_device_data itself.
This avoids an additional allocation and the ifdef.  It also gets rid of
some indirection.

Also use dev_err instead of pr_err in the changed code.
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NRodolfo Giometti <giometti@enneenne.com>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This removes some boilerplate code (no functional changes).
Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Acked-by: NRodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Luebbe <jlu@pengutronix.de>
Acked-by: NRodolfo Giometti <giometti@enneenne.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Replaced calls to kmalloc and memset with kzalloc.
Patch found using coccinelle.
Signed-off-by: NAlexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NEd Cashin <ecashin@coraid.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NEd Cashin <ecashin@coraid.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Some users have a large AoE target while others like to use many AoE
targets at the same time.  In the latter case, there is an opportunity to
greatly improve aggregate throughput by allowing different threads to
complete the I/O associated with each target.  For 36 targets, 4 KiB read
throughput roughly doubles, for example, with these changes in place.
Signed-off-by: NEd Cashin <ecashin@coraid.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, when a disconnect is requested by the user (via NBD_DISCONNECT
ioctl) the return from NBD_DO_IT is undefined (it is usually one of
several error codes).  This means that nbd-client does not know if a
manual disconnect was performed or whether a network error occurred.
Because of this, nbd-client's persist mode (which tries to reconnect after
error, but not after manual disconnect) does not always work correctly.

This change fixes this by causing NBD_DO_IT to always return 0 if a user
requests a disconnect.  This means that nbd-client can correctly either
persist the connection (if an error occurred) or disconnect (if the user
requested it).
Signed-off-by: NPaul Clements <paul.clements@steeleye.com>
Acked-by: NRob Landley <rob@landley.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The NBD_CLEAR_QUE ioctl has been deprecated for quite some time (its job
is now done by two other ioctls).  We should stop trying to make bogus
assertions in it.  Also, user-level code should remove calls to
NBD_CLEAR_QUE, ASAP.
Signed-off-by: NMichal Belczyk <belczyk@bsd.krakow.pl>
Signed-off-by: NPaul Clements <paul.clements@steeleye.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Change endpoint device name format to use a component tag value instead of
device destination ID.

RapidIO specification defines a component tag to be a unique identifier
for devices in a network.  RapidIO switches already use component tag as
part of their device name and also use it for device identification when
processing error management event notifications.

Forming an endpoint's device name using its component tag instead of
destination ID allows to keep sysfs device directories unchanged in case
if a routing process dynamically changes endpoint's destination ID as a
result of route optimization.

This change should not affect any existing users because a valid device
destination ID always should be obtained by reading "destid" attribute and
not by parsing device name.

This patch also removes switchid member from struct rio_switch because it
simply duplicates the component tag and does not have other use than in
device name generation.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add RapidIO-specific modalias generation to enable udev notifications
about RapidIO-specific events.

The RapidIO modalias string format is shown below:

"rapidio:vNNNNdNNNNavNNNNadNNNN"

Where:
v  - Device Vendor ID (16 bit),
d  - Device ID (16 bit),
av - Assembly Vendor ID (16 bit),
ad - Assembly ID (16 bit),

as they are reported in corresponding Capability Registers (CARs)
of each RapidIO device.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a configuration option to build RapidIO subsystem core code as a
loadable kernel module.  Currently this option is available only for
x86-based platforms, with the additional patch for PowerPC planned to be
provided later.

This patch replaces kernel command line parameter "riohdid=" with its
module-specific analog "rapidio.hdid=".
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds an option to build device driver for Tsi721 PCIe-to-SRIO
bridge device as a kernel module.

Currently this module cannot be unloaded because the existing RapidIO
subsystem code does not support dynamic removal of local RapidIO
controllers (TODO).
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update enumeration/discovery method registration mechanism to allow
loading enumeration/discovery methods before all mports are registered.

Existing statically linked RapidIO subsystem expects that all available
RapidIO mport devices are initialized and registered before the
enumeration/discovery method is registered.  Switching to loadable mport
device drivers creates situation when mport device driver can be loaded
after enumeration/discovery method is attached (e.g., loadable mport
driver in a system with statically linked RapidIO core and enumerator).
This also will happen in a system with hot-pluggable RapidIO controllers.

To remove the dependency on the initialization/registration order this
patch introduces enumeration/discovery registration mechanism that
supports arbitrary registration order of mports and enumerator/discovery
methods.

The following registration rules are implemented:
- only one enumeration/discovery method can be registered for given mport ID
  (including RIO_MPORT_ANY);
- when new enumeration/discovery methods tries to attach to the registered mport
  device, method with matching mport ID will replace a default method previously
  registered for given mport (if any);
- enumeration/discovery method with target ID=RIO_MPORT_ANY will be attached
  only to mports that do not have another enumerator attached to them;
- when new mport device is registered with RapidIO subsystem, registration
  routine searches for the enumeration/discovery method with the best matching
  mport ID;
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework probe/remove routines to prevent rionet driver from monopolizing
target RapidIO devices.  Fix conflict with modular RapidIO switch drivers.

Using one of RapidIO messaging channels rionet driver provides a service
layer common to all endpoint devices in a system's RapidIO network.  These
devices may also require their own specific device driver which will be
blocked from attaching to the target device by rionet (or block rionet if
loaded earlier).  To avoid conflict with device-specific drivers, the
rionet driver is reworked to be registered as a subsystem interface on the
RapidIO bus.

The reworked rio_remove_dev() and rionet_exit() routines also include
handling of individual rionet peer device removal which was not supported
before.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Rework RapidIO switch drivers to add an option to build them as loadable
kernel modules.

This patch removes RapidIO-specific vmlinux section and converts switch
drivers to be compatible with LDM driver registration method.  To simplify
registration of device-specific callback routines this patch introduces
rio_switch_ops data structure.  The sw_sysfs() callback is removed from
the list of device-specific operations because under the new structure its
functions can be handled by switch driver's probe() and remove() routines.

If a specific switch device driver is not loaded the RapidIO subsystem
core will use default standard-based operations to configure a switch.
Because the current implementation of RapidIO enumeration/discovery method
relies on availability of device-specific operations for error management,
switch device drivers must be loaded before the RapidIO
enumeration/discovery starts.

This patch also moves several common routines from enumeration/discovery
module into the RapidIO core code to make switch-specific operations
accessible to all components of RapidIO subsystem.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Cc: Stef van Os <stef.van.os@Prodrive.nl>
Cc: Jean Delvare <jdelvare@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

sparse warnings:

drivers/rapidio/rio-scan.c:1143:5: sparse: symbol 'rio_enum_mport' was not declared. Should it be static?
drivers/rapidio/rio-scan.c:1246:5: sparse: symbol 'rio_disc_mport' was not declared. Should it be static?
Signed-off-by: NFengguang Wu <fengguang.wu@intel.com>
Cc: "Bounine, Alexandre" <Alexandre.Bounine@idt.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove the driver for Tsi500 Parallel RapidIO switch because this device
has not been available for several years.  Since the first introduction of
Tsi500, the parallel RapidIO interface was replaced by the serial RapidIO
(sRIO) and therefore there is no value in keeping this driver.
Signed-off-by: NAlexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

/dev/oldmem provides the interface for us to access the "old memory" in
the dump-capture kernel.  Unfortunately, no one actually uses this
interface.

And this interface could actually cause some real problems if used on ia64
where the cached/uncached accesses are mixed.  See the discussion from the
link: https://lkml.org/lkml/2013/4/12/386.

So Eric suggested that we should remove /dev/oldmem as an unused piece of
code.

[akpm@linux-foundation.org: mention /dev/oldmem obsolescence in devices.txt]
Suggested-by: N"Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Dave Hansen <dave@sr71.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Tony Luck <tony.luck@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On CSR SiRFprimaII/atlasVI, there is a programmable 16-bit divider
(RTC_DIV) that divides the input 32.768KHz clock to the frequency that
users need (E.g.  1 Hz).  The divided real-time clock will be used to
drive a 32-bit counter (RTC_COUNTER) that provides users with the actual
time.

In each cycle of the divided real-time clock, there is a Hertz interrupt
generated to the RISC.  Users can also configure an alarm (RTC_ALARM).
When RTC_COUNTER matches the alarm, there will be an alarm interrupt
generated to the RISC.

The system RTC can generate an alarm wake-up signal to notify the power
controller to wake up from power saving mode.
Signed-off-by: NXianglong Du <Xianglong.Du@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use module_platform_driver_probe() macro which makes the code smaller and
simpler.
Signed-off-by: NFabio Porcedda <fabio.porcedda@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

rtc-omap driver modules is used both by OMAP1/2, Davinci SoC platforms.

However, rtc wake support on OMAP1 is broken.  Hence the
device_init_wakeup() was removed from rtc-omap driver and moved to
platform board files that supported it (DA850/OMAP-L138).  [1]

However, recently [2] it was suggested that driver should always do a
device_init_wakeup(dev, true). Platforms that don't want/need
wakeup support can disable it from userspace via:

    echo disabled > /sys/devices/.../power/wakeup

Also, with the new DT boot-up, board file doesn't exist and hence there
is no way to have device wakeup support rtc.

The fix for above issues, is to hard code device_init_wakeup() inside
driver and let platforms that don't need this, handle it through the
sysfs power entry.

[1]
https://patchwork.kernel.org/patch/136731/

[2]
http://www.mail-archive.com/davinci-linux-open-source@linux.
davincidsp.com/msg26077.html
Signed-off-by: NHebbar Gururaja <gururaja.hebbar@ti.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Added support for NXP PCF2127 RTC (i2c).

[akpm@linux-foundation.org: fix typo, fix warnings]
Signed-off-by: NRenaud Cerrato <r.cerrato@til-technologies.fr>
Cc: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Enable dev as wakeup device before calling rtc_device_register(), so that
it can create the "wakealarm" sysfs.
Signed-off-by: NWei Ni <wni@nvidia.com>
Acked-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Convert drivers/rtc/class to use dev_pm_ops for power management and
remove Legacy PM ops hooks.  With this change, rtc class registers
suspend/resume callbacks via class->pm (dev_pm_ops) instead of Legacy
class->suspend/resume.  When __device_suspend() runs call-backs, it will
find class->pm ops for the rtc class.
Signed-off-by: NShuah Khan <shuah.kh@samsung.com>
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Cc: Shuah Khan <shuahkhan@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The usage of strict_strtoul() is not preferred, because strict_strtoul()
is obsolete.  Thus, kstrtoul() should be used.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Reviewed-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If rtc->irq_task is non-NULL and task is NULL, they always
rtc_irq_set_freq(), whenever err is set to -EBUSY it will then immediately
be set to -EACCES, misleading the caller as to the underlying problem.
Signed-off-by: NChris Brand <chris.brand@broadcom.com>
Acked-by: NAlessandro Zummo <a.zummo@towertech.it>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use module_platform_driver() to register the platform driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NKevin Hilman <khilman@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Initialize the rtc_reg_map in platform_driver's probe function instead at
module_init time.  This way we can make sure that the twl-core has been
already probed and initialized (twl_priv->twl_id is valid) since the
platform device for the RTC driver will be created by the twl-core after
it finished its init.
Reported-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Tested-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The bios may clear the rtc control register when resuming the system. Since the
cmos interrupt handler may now be run before the rtc_cmos is resumed, this can
cause the interrupt handler to ignore an alarm since the alarm bit is not set in
the rtc control register. To work around this, check if the rtc_cmos is
suspended and use the stored value for the rtc control register.
Signed-off-by: NDerek Basehore <dbasehore@chromium.org>
Reviewed-by: NSameer Nanda <snanda@chromium.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: John Stultz <john.stultz@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Currently, the RTC IRQ is never wakeup-enabled so is not capable of
bringing the system out of suspend.

On OMAP platforms, we have gotten by without this because the TWL RTC is
on an I2C-connected chip which is capable of waking up the OMAP via the IO
ring when the OMAP is in low-power states.

However, if the OMAP suspends without hitting the low-power states (and
the IO ring is not enabled), RTC wakeups will not work because the IRQ is
not wakeup enabled.

To fix, ensure the RTC IRQ is wakeup enabled whenever the RTC alarm is
set.
Signed-off-by: NKevin Hilman <khilman@linaro.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use of PTR_RET() simplifies the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use of PTR_RET() simplifies the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use of PTR_RET() simplifies the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use of PTR_RET() simplifies the code.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Roman Fietze <roman.fietze@telemotive.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>