There are two front-panel LEDs on MPC837xRDB and MPC8315RDB boards: PWR
and HDD. After adding appropriate nodes we can program these LEDs from
kernel and user space.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Since USB2 is shared with local bus, either local bus or USB2
should be disabled. By default U-Boot enables local bus, so we
have to disable USB2, otherwise kernel hangs:

 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
 fsl-ehci fsl-ehci.0: irq 28, io base 0xffe22000
 fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
 hub 1-0:1.0: USB hub found
 hub 1-0:1.0: 1 port detected
 fsl-ehci fsl-ehci.1: Freescale On-Chip EHCI Host Controller
 fsl-ehci fsl-ehci.1: new USB bus registered, assigned bus number 2
 <hangs here>

Note that U-Boot doesn't clear 'status' property when it enables
USB2, so we have to comment out the whole node.

To enable USB2, one can issue
'setenv hwconfig usb2:dr_mode=<host|peripheral>' command at the
U-Boot prompt.
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

This patch adds support for eTSEC 2.0 as found in P1020.
The changes include introduction of the group nodes for
the etsec nodes.
Signed-off-by: NSandeep Gopalpet <sandeep.kumar@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Technically, whilst SEC v3.3 h/w honours the tls_ssl_stream descriptor
type, it lacks the ARC4 algorithm execution unit required to be able
to execute anything meaningful with it.  Change the node to agree with
the documentation that declares that the sec3.3 really doesn't have such
a descriptor type.
Reported-by: NHaiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: NKim Phillips <kim.phillips@freescale.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Acked-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Enable the DEBUG_PER_CPU_MAPS option so we can look for problems with
cpumasks .
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Convert to the new cpumask API.

irq_choose_cpu can be simplified by using cpumask_next and cpumask_first.

smp_mpic_message_pass was doing open coded cpumask manipulation and passing an
int for a cpumask into mpic_send_ipi. Since mpic_send_ipi is only used
locally, make it static and convert it to take a cpumask. This allows us
to clean up the mess in smp_mpic_message_pass.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Since the *_map cpumask variants are deprecated, change the comments to
instead refer to *_mask.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Convert NUMA code to new cpumask API. We shift the node to cpumask
setup code until after we complete bootmem allocation so we can
dynamically allocate the cpumasks.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Convert hotplug-cpu code to new cpumask API.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Dynamically allocate cpu_sibling_map and cpu_core_map cpumasks.

We don't need to set_cpu_online() the boot cpu in smp_prepare_boot_cpu,
init/main.c does it for us.

We also postpone setting of the boot cpu in cpu_sibling_map and cpu_core_map
until when the memory allocator is available (smp_prepare_cpus), similar
to x86.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use new cpumask API in /proc/cpuinfo code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This separates the per cpu output from the summary output at the end of the
file, making it easier to convert to the new cpumask API in a subsequent
patch.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use the new cpumask API and add some comments to clarify how get_irq_server
works.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use new cpumask functions in pseries SMP startup code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use new cpumask functions in iseries SMP startup code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use new cpumask_* functions, and dynamically allocate cpumask in fixup_irqs.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use the new cpumask_* functions and dynamically allocate the cpumask in
smp_cpus_done.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Use cpumask_first, cpumask_next in rtasd code.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Change &cpu_online_map to cpu_online_mask.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

As explained in commit 1c0fe6e3, we want to call the architecture independent
oom killer when getting an unexplained OOM from handle_mm_fault, rather than
simply killing current.

Cc: linuxppc-dev@ozlabs.org
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-arch@vger.kernel.org
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We need to keep track of the backing pages that get allocated by
vmemmap_populate() so that when we use kdump, the dump-capture kernel knows
where these pages are.

We use a simple linked list of structures that contain the physical address
of the backing page and corresponding virtual address to track the backing
pages.
To save space, we just use a pointer to the next struct vmemmap_backing. We
can also do this because we never remove nodes.  We call the pointer "list"
to be compatible with changes made to the crash utility.

vmemmap_populate() is called either at boot-time or on a memory hotplug
operation. We don't have to worry about the boot-time calls because they
will be inherently single-threaded, and for a memory hotplug operation
vmemmap_populate() is called through:
sparse_add_one_section()
            |
            V
kmalloc_section_memmap()
            |
            V
sparse_mem_map_populate()
            |
            V
vmemmap_populate()
and in sparse_add_one_section() we're protected by pgdat_resize_lock().
So, we don't need a spinlock to protect the vmemmap_list.

We allocate space for the vmemmap_backing structs by allocating whole pages
in vmemmap_list_alloc() and then handing out chunks of this to
vmemmap_list_populate().

This means that we waste at most just under one page, but this keeps the code
is simple.
Signed-off-by: NMark Nelson <markn@au1.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently the parsing of the device tree in
arch/powerpc/include/asm/parport.h assumes that the interrupt provided in
the parallel port node is a valid virtual irq. The values for the
interrupts provided in the device tree should have meaning in the context
of the driver for the specific interrupt controller to which the interrupt
is connected and irq_of_parse_and_map() should be used to determine the
correct virtual irq.
Signed-off-by: NMartyn Welch <martyn.welch@ge.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

So we tried to speed things up a bit using flush_hash_pages() directly
but that falls over on 603 of course meaning we fail to flush the TLB
properly and we may even end up having it corrupt memory randomly by
accessing a hash table that doesn't exist.

This removes the "optimization" by always going through flush_tlb_page()
for now at least.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Currently we always call start-cpu irrespective of if the CPU is
stopped or not. Unfortunatley on POWER7, firmware seems to not like
start-cpu being called when a cpu already been started.  This was not
the case on POWER6 and earlier.

This patch checks to see if the CPU is stopped or not via an
query-cpu-stopped-state call, and only calls start-cpu on CPUs which
are stopped.

This fixes a bug with kexec on POWER7 on PHYP where only the primary
thread would make it to the second kernel.
Reported-by: NAnkita Garg <ankita@linux.vnet.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This moves query_cpu_stopped() out of the hotplug cpu code and into
smp.c so it can called in other places and renames it to
smp_query_cpu_stopped().

It also cleans up the return values by adding some #defines

Cc: <stable@kernel.org>
Signed-off-by: NMichael Neuling <mikey@neuling.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

By setting "reset_type" to one of the following values, the default
software reset mechanism may be overidden. Here the possible values of
"reset_type":

  1 - PPC4xx core reset
  2 - PPC4xx chip reset
  3 - PPC4xx system reset (default)

This will be used by a new PPC440SPe board port, which needs a "chip
reset" instead of the default "system reset" to be asserted.
Signed-off-by: NStefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

A defconfig for the IBM ISS 476 simulator
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This is a trivial 4xx plaform that uses the new simple bsp from
Josh and is handy to use in simulators such as ISS or even Mambo
who don't properly implement most of the actual devices in the
SoC but really only the core.
Signed-off-by: NTorez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

476 requires an isync after loading MMU and debug related SPR's.  Some of
these are in performance-critical paths and may need to be optimized, but
initially, we're playing it safe.
Signed-off-by: NTorez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The 47x core's MCSR varies from 44x, so it needs it's own machine check
handler.
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds the base support for the 476 processor.  The code was
primarily written by Ben Herrenschmidt and Torez Smith, but I've been
maintaining it for a while.

The goal is to have a single binary that will run on 44x and 47x, but
we still have some details to work out.  The biggest is that the L1 cache
line size differs on the two platforms, but it's currently a compile-time
option.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NTorez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The 47x platform supports multiple cores and shares code with 44x.
Break out code that is common for initializing the primary and secondary
cpus into a function which can be called for both.
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

This patch adds a marker to the exception stack frame to aid in debugging.
It's already inserted on other platforms and xmon recognizes it and
identifies exception frames when showing stack traces.
Signed-off-by: NTorez Smith  <lnxtorez@linux.vnet.ibm.com>
Signed-off-by: NDave Kleikamp <shaggy@linux.vnet.ibm.com>
Signed-off-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>

The bypassing of this test is a leftover from 2.4 vintage
kernels, and is no longer appropriate, or even used by KGDB.
Currently KGDB uses probe_kernel_write() for all access to
memory via the KGDB core, so it can simply be deleted.

This fixes CVE-2010-1446.

CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
CC: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: NWufei <fei.wu@windriver.com>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>

Refresh ps3_defconfig to latest kernel sources and change
these kernel config options:

  o CONFIG_USB_ANNOUNCE_NEW_DEVICES: n -> y
  o CONFIG_USB_EHCI_TT_NEWSCHED: n -> y
  o CONFIG_CMDLINE_BOOL: n -> y
  o CONFIG_CMDLINE: n -> ""
Signed-off-by: NGeoff Levand <geoff@infradead.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

This ensures that the translations for unmapped IO mappings or
unmapped memory are properly removed from the MMU hash table
before such an unplug. Without this, the hypervisor refuses the
unplug operations due to those resources still being mapped by
the partition.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

Firmware changed the way it represents memory and cpu affinity on POWER7.
Unfortunately the old method now caps the topology to work around issues
with legacy operating systems. For Linux to get the correct topology we
need to use the new form 1 affinity information.

We set the form 1 field in the client architecture, and if we see "1" in the
ibm,associativity-form property firmware supports form 1 affinity and
we should look at the first field in the ibm,associativity-reference-points
array. If not we use the second field as we always have.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

The following commit broke CONFIG_RELOCATABLE support on FSL Book-E
parts:

commit 549e8152
Author: Paul Mackerras <paulus@samba.org>
Date:   Sat Aug 30 11:43:47 2008 +1000

    powerpc: Make the 64-bit kernel as a position-independent executable

The change to __va and __pa to use PAGE_OFFSET & MEMORY_START causes
problems on the Book-E parts because we don't know MEMORY_START until
after we parse the device tree.  We need __va to work properly to even
parse the device tree so we have a chicken an egg.  So go back to using
he other definition of __va/__pa on CONFIG_BOOKE and use the
PAGE_OFFSET/MEMORY_START version on "Classic" PPC64.

Also updated casts to handle phys_addr_t being a different size from
unsigned long (ie 36-bit physical on PPC32).
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>

Int is not long enough to store the size of a dirty bitmap.

This patch fixes this problem with the introduction of a wrapper
function to calculate the sizes of dirty bitmaps.

Note: in mark_page_dirty(), we have to consider the fact that
  __set_bit() takes the offset as int, not long.
Signed-off-by: NTakuya Yoshikawa <yoshikawa.takuya@oss.ntt.co.jp>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>