Add LCD panel platform data for the AP325RXA board.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add Migo-R specific platform data for on-chip sh7722 CEU and ov772x camera.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add WVGA and QVGA LCD panel support to Migo-R.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

I think this problem is GCC(4.1.2) bug.
Syscall "getdents" returned "dirent->d_off" is always 0.
I think other EB enviroment have same problem.

Problem code
0c03c954 <filldir>:
 :
 c03c97a:       58 f7           mov.l   @(28,r15),r8 !-> offset (high)
 c03c97c:       59 f8           mov.l   @(32,r15),r9 !-> offset (low)
 c03c97e:       53 f9           mov.l   @(36,r15),r3
 c03c980:       54 fa           mov.l   @(40,r15),r4
 :
 c03c9a0:       21 82           mov.l   r8,@r1 !offset(high) -> dirent->d_off

It's workaround patch.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This wires up the signalfd4, eventfd2, epoll_create1, dup3, pipe2, and
inotify_init1 syscalls.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

fix the problem that cannot boot using uImage when PAGE_SIZE is
8kbyte or 64kbyte.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remove request_mem_region() and release_mem_region() from sh_keysc driver.
Those functions can find resource conflict, but it is already checked in
platform_device_add().
Signed-off-by: NTetsuya Mukawa <mukawa@igel.co.jp>
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Without this patch, signals sent during architecture specific signal
handling (typically as a result of the user's stack being inaccessible)
are ignored.

This is the SH version of commit c3ff8ec3
which was for the i386.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() in the sh7366 processor code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7343 processor and in the board code
for Solution Engine 7343. Remove duplicate MSTPCR register definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7722 processor and in the board code
for Migo-R and Solution Engine 7722. Remove duplicate MSTPCR register
definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Use clk_always_enable() on the sh7723 processor and in the ap325rxa
board code. Remove duplicate MSTPCR register definitions.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SuperH specific funcion clk_always_enable(), useful to enable MSTPCR
bits in processor or board specific code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Show all clocks in /proc/clocks, and also show if they are enabled or
disabled. This is useful to show MSTPCR bits on SuperH Mobile processors.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This code makes sh7343 share the sh7722 clock code. Instead of just using
the good and very old sh7343 clock implmentation, switch to the new MSTPCR
enabled clock code. SIU clocks are disabled on sh7343 for now.

With this change all SuperH Mobile devices now use the same clock code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Handle module stop clock bits in MSTPCRn through the clock framework.
The clocks are named after the bits in the data sheet. The association
between bit number and hardware block is processor specific.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Make use of arch_flags to simplify the SIU clock code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add arch_flags to struct clk so we can keep per-clock private data
somewhere and share code between multiple clocks.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Commit 1ea0704e
(mm: add a ptep_modify_prot transaction abstraction)
triggered on sh build errors like the following:

<--  snip  -->

...
  CC      arch/sh/mm/pg-sh4.o
cc1: warnings being treated as errors
include2/asm/pgtable.h:139: error: 'ptep_get_and_clear' declared inline after being called
include2/asm/pgtable.h:139: error: previous declaration of 'ptep_get_and_clear' was here
make[2]: *** [arch/sh/mm/pg-sh4.o] Error 1

<--  snip  -->

Since there's no good reason for marking these global functions as
"inline" this patch therefore removes the inline's.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds initial support for the Renesas R0P7785LC0011RL board.
This patch supports 29bit address mode only.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds physically contiguous memory chunks to the UIO devices.
The same strategy can be used in the future for the CEU as well.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU, VEU(1) and VEU(2) blocks of the sh7366
to user space using the uio_pdrv_genirq platform driver.

While at it, fix up the VEU(2) interrupt vector.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU, VEU2H0 and VEU2H1 blocks of the sh7723
to user space using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU and VEU blocks of the sh7722 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch exports the VPU and VEU blocks of the sh7343 to user space
using the uio_pdrv_genirq platform driver.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch is

By sh2
- Remove duplicate code
- Reduce stack usage
- Cleanup and little optimize

By sh2a
- Add missing handler(256 to 511)
- Use sh2a instructions handler
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

updated the following codes for Solution Endine 7343:
 - fix compile error in arch/sh/boards/se/7343/irq.c
 - add nor flash physmaps
 - update defconfig
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

updated the following codes for SH7343:
 - add register_intc_controller()
 - add EARLY_SCIF_CONSOLE_PORT
 - add define of CPG register
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Remove inline from ptep_get_and_clean() to match with header file prototype.
Makes linux-next build.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch enables I2C on the sh7723-based ap325rxa board.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7366.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for the single I2C channel on sh7723.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds platform data for two I2C channels to the sh7343.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The current kernel behaviour is to reenable interrupts unconditionally
when taking a page fault. This patch changes this to only enable them
if interrupts were previously enabled.

It also fixes a problem seen with this fix in place: the kernel previously
flushed the vsyscall page when handling a signal, which is not only
unncessary, but caused a possible sleep with interrupts disabled.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add implementation of flush_icache_range() suitable for signal handler
and kprobes. Remove flush_cache_sigtramp() and change signal.c to use
flush_icache_range().
Signed-off-by: NChris Smith <chris.smith@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>