Current code attempts to clean up resources when queue create fails and there it
invokes queue free call with a (NULL) pointer to the queue which could not be
allocated in the first place. Fix it by returning directly without invoking the
queue free call as no resources has been allocated at that point of time.
Reported-by: NJiri Slaby <jirislaby@gmail.com>
Signed-off-by: NAnirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A memory use after free bug can manifest if the MTSETBLK or SET_DENS_AND_BLK
ioctl features are used to set the tape's blocksize from 0 to non-zero.
After the driver sets the new block size, in this one case it calls
normalize_buffer() to free the device's internal data buffers.  However, the
ioctl code assumes there is always a buffer and does not check or allocate
a buffer if there isn't one.  So any following ioctl calls can corrupt
a part of memory by writing data to memory that the st driver had freed.

This patch removes the normalize_buffer() call and the specialness of
changing from a 0 to non-zero blocksize to fix the possible use of
memory after it has been freed by the st driver.
signed-off-by: NDavid Jeffery <djeffery@redhat.com>
Acked-by: NKai Makisara <kai.makisara@kolumbus.fi>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch contains changes to use pci_pools for iscsi hdr
instead of pci_alloc_consistent. Here we alloc and free to pool
for every IO

v3:
- Remove cleanup loop in beiscsi_session_destroy
- Fixup for allocation failure handling in beiscsi_alloc_pdu
- Removed unused variable in beiscsi_session_destroy.

[jejb: fix up pci_pool_alloc address sizing problem]
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This patch contains changes that allow iscsi_session_setup
to allocate private space for LLD's
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Acked-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[v2: fixed up virt_to_bus() issue spotted by sfr]
Signed-off-by: NMike Christie <michaelc@cs.wisc.edu>
Signed-off-by: NJayamohan Kallickal <jayamohank@serverengines.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Bump version to 02.100.03.00
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support to process device removal events when the phy status is set to
MPI2_EVENT_SAS_TOPO_PHYSTATUS_VACANT.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Following a diag_reset, a request to send an ioc_init is timing out.  The
timeout occurred within the HANDSHAKE logic while waiting on firmware to
acknowledge that the driver had wrote to the doorbell register.  This was
root caused to a logic timeout in the firmware code.  The proposed solution
is for the driver to call the udelay instead of msleep API in function where
its looping reading the interrupt status.  In addition to this change, there
were two additional cases where we deleted the clearing interrupt status
outside handshake context.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Now driver call init_completion on a per request basis.  At some
point the wait_for_completion_timeout is not waiting for the timeout,
instead returning immediately, thus going into diag reset.  This fix will
address all request using the wait_for_completion_timeout API. The previous
implimentation was only calling init_completion at driver
load time.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

(1) Added three new functions to handle sending target resest and OP_REMOVE
from interrupt time, they are _scsih_tm_tr_send, _scsih_tm_tr_complete, and
_scsih_sas_control_complete.  This code will create a link list of pending
target resets if there is no more available request in the hipriority
request queue.  The list is stored in ioc->delayed_tr_list.

(2) All callback handler return type is changed from void to u8.
Now _base_interrupt will check for return type of callback handlers to
take decision of message frame is already freed or not.
In genral,
Return 1 meaning mf should be freed from _base_interrupt
       0 means the mf is freed from function.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

1) create a pool of high priority message frames in the region of memory
between message frames and chains.  The modifications are in
_base_allocate_memory_pools.  Also create a seperate pool of memory for
internal commands located near the same region of memory.  The pool of high
priority message frames is restriced by the facts->HighPriorityCredit.

2) Create additional API for accessing request message frames. New function
mpt2sas_base_get_smid_hpr is for highpriority request. New function
mpt2sas_base_get_smid_scsiio for SCSI_IO, passing in the scsi command
pointer.  The mpt2sas_base_get_smid function is for requesting internal
commands.

3) Added new function _base_get_cb_idx to obtain the callback
index from one of the three pools of request message frames.

4) Removed wrapper functions _scsih_scsi_lookup_set and
_scsih_scsi_lookup_getclear. These were removed because this handling was
moved into mpt2sas_base_get_smid_scsiio and mpt2sas_base_free_smid.

5) The function mpt2sas_base_free_smid is modified so the request message
frames are put back on one of the three pools of request message frames.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Update the copyright year to 2009 through out the code.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Added new file for MPI2 header version history.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Drivers header are updated to the MPI2 REV K headers.
Renamed VF_ID to msix_index in all call back handlers.
VF_ID is removed from all request descriptor.
Signed-off-by: NKashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add new driver for Brocade Hardware
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add missing kernel-doc notation in scsi_transport_fc.c:

Warning(drivers/scsi/scsi_transport_fc.c:3593): No description found for parameter 'q'
Warning(drivers/scsi/scsi_transport_fc.c:3700): No description found for parameter 'q'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Add support for 32-byte READ/WRITE as well as DIF Type 2 protection.

Reject protected 10/12/16 byte READ/WRITE commands when Type 2 is
enabled.

Verify Type 2 reference tag according to Expected Initial LBA in 32-byte
CDB.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Disks formatted with DIF Type 2 reject READ/WRITE 6/10/12/16 commands
when protection is enabled.  Only the 32-byte variants are supported.

Implement support for issusing 32-byte READ/WRITE and enable Type 2
drives in the protection type detection logic.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

We would leak a scsi_data_buffer if the free_list command was of the
protected variety.
Reported-by: NBoaz Harrosh <bharrosh@panasas.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

So far we have only issued DIF commands if CONFIG_BLK_DEV_INTEGRITY is
enabled.  However, communication between initiator and target should be
independent of protection information DMA.  There are DIF-only host
adapters coming out that will be able to take advantage of this.

Move the relevant DIF bits to sd.c.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The checksum format is orthogonal to whether the protection information
is being passed on beyond the HBA or not.  It is perfectly valid to use
a non-T10 CRC with WRITE_STRIP and READ_INSERT.

Consequently it no longer makes sense to explicitly refer to the
conversion in the protection operation.  Update sd_dif and lpfc
accordingly.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Acked-by: NIhab Hamadi <Ihab.Hamadi@Emulex.Com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

A target reset when I/O is ongoing might result
an eventual device offline, as scsi_eh_completed_normally()
might return ADD_TO_MLQUEUE in addition to the
advertised SUCCESS, FAILED, and NEEDS_RETRY.

Which is unfortunate as scsi_send_eh_cmnd() will
therefore map ADD_TO_MLQUEUE to FAILED instead of
the more appropriate NEEDS_RETRY.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Running sg_luns on s390x with CONFIG_DEBUG_PAGEALLOC enabled fails
with EFAULT from the SG_IO ioctl. The EFAULT is the result from
copy_to_user failing in this call chain:

sg_ioctl
sg_new_read
sg_finish_rem_req
blk_rq_unmap_user
__blk_rq_unmap_user
bio_uncopy_user
__bio_copy_iov
copy_to_user

The sg driver calls sg_remove_scat to free the memory pages before
calling blk_rq_unmap_user that tries to copy the data back to
userspace. Change the order to first call blk_rq_unmap_user before
freeing the pages in sg_remove_scat.
Acked-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: stable@kernel.org
Signed-off-by: NChristof Schmitt <christof.schmitt@de.ibm.com>
Acked-by: NDouglas Gilbert <dgilbert@interlog.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

On certain cases, UDF disc doesn't report capacity correctly via
READ_CAPACITY but TOC or trackinfo contains valid information which
can be obtained using cdrom_get_last_written().  ide-cd considers both
values and uses the larger one.  Do the same in sr.  This fixes
bko#9668.

 http://bugzilla.kernel.org/show_bug.cgi?id=9668Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NMilan Kocian <milan.kocian@wq.cz>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

5706/5708/5709 devices allow driver/user to set page size. By default it is
set to 4096.  Current drivers do not program this register based on
architecture type (e.g. x86 = 4K, IA64 = 16K) and by choice lets device use
the defaults. So while mapping connection context memory (doorebll registers),
driver has to match page size used by the device. Included change fixes the
issue we uncovered during IA64 testing
Signed-off-by: NAnil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

Most code changes were made to support RR44xx adapters.
- add more PCI device ID.
- using PCI BAR[2] to access RR44xx IOP.
- using PCI BAR[0] to check and clear RR44xx IRQ.
Signed-off-by: NHighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

The function mode_select_handle_sense returns SCSI_DH_OK even when there is a sense code which is incorrect. Removing it so that it returns SCSI_DH_IO when there is sense that is not handled by this function.
Signed-off-by: NBabu Moger <babu.moger@lsi.com>
Reviewed-by: NVijay Chauhan <vijay.chauhan@lsi.com>
Reviewed-by: NBob Stankey <Robert.stankey@lsi.com>
Reviewed-by: NChandra Seetharaman <sekharan@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

1.Changed driver prints to use scmd_printk, sdev_printk
2.Changed dev_err calls to scmd_printk for scsi related print messages
Signed-off-by: NAnil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

This is support for Areca SAS/SATA HBA, ARC-1300/1320, which quipped with
88SE6440/88SE9480 respectively.

Signed-off-by: Nick Cheng< nick.cheng@areca.com.tw >
Cc: Ke Wei <kewei.mv@gmail.com>
Signed-off-by: NJames Bottomley <James.Bottomley@suse.de>

[akpm@linux-foundation.org: fix KVM]
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code

But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* remove asm/atomic.h inclusion from kref.h -- not needed, linux/types.h
  is enough for atomic_t
* remove linux/kref.h inclusion from files which do not need it.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make all seq_operations structs const, to help mitigate against
revectoring user-triggerable function pointers.

This is derived from the grsecurity patch, although generated from scratch
because it's simpler than extracting the changes from there.
Signed-off-by: NJames Morris <jmorris@namei.org>
Acked-by: NSerge Hallyn <serue@us.ibm.com>
Acked-by: NCasey Schaufler <casey@schaufler-ca.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

fix the following 'make includecheck' warning:

  drivers/scsi/ibmvscsi/ibmvscsi.c: asm/firmware.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247067016.4382.78.camel@ht.satnam>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>

fix the following 'make includecheck' warning:

  drivers/scsi/fcoe/libfcoe.c: linux/netdevice.h is included more than once.
Signed-off-by: NJaswinder Singh Rajput <jaswinderrajput@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
LKML-Reference: <1247066936.4382.76.camel@ht.satnam>

Let attribute group vectors be declared "const".  We'd
like to let most attribute metadata live in read-only
sections... this is a start.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>