We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We should not have multiple line files in sysfs, this moves the data to
debugfs instead, like the UHCI driver.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch hands over the port to the companion when the
hub_port_connect_change fails.
Signed-off-by: NBalaji Rao <balajirrao@gmail.com>
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Continue is not needed at the bottom of a loop.

The semantic patch implementing this change is as follows:

@@
@@

for (...;...;...) {
   ...
   if (...) {
     ...
-   continue;
   }
}
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Convert from class_device to device for drivers/usb/core.
Signed-off-by: NTony Jones <tonyj@suse.de>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Move the tps65010 header file from the OMAP arch directory to the
more generic <linux/i2c/...> directory, and remove the spurious
dependency of this driver on OMAP.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

I2C driver IDs are optional, so if you don't need one, just omit it.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>

Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:

http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html

This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix.  The drivers will still bind against
the older names also.
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: Neric miao <eric.miao@marvell.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The OHCI IRQ handler has an optimisation that avoids reading some
chip registers when the controller reports that the interrupt was
triggered *only* because completed requests were written into the
controller's "done list" and handed to the host.

This mechanism can't be used on some controllers.  Among others, it
fails for the SA1111 and the AMCC 440EP PowerPC processor.

This patch removes the optimisation and makes the code clearer.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Host controller IRQs are supposed to be serviced with interrupts
disabled.  This patch (as1026) adds an IRQF_DISABLED flag to all the
controller drivers that lack it.  It also replaces the
spin_lock_irqsave() and spin_unlock_irqrestore() calls in uhci_irq()
with simple spin_lock() and spin_unlock().

This fixes Bugzilla #9335.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

A recent patch added software synchronization during EHCI startup,
so ports aren't switched away from the companion controllers after
resets have started.  This patch adds a short delay letting hardware
finish that port switching before any new resets begin ... so both
ends of that hardware race window are closed.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: Dave Miller <davem@davemloft.net>
Cc: Dely Sy <dely.l.sy@intel.com>
Cc: stable <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a bug introduced by
commit b22817b3.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Buesch <mb@bu3sch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove various newly-introduced compiler warnings for OHCI.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

fix ssb_ohci_probe() build bug:

 drivers/built-in.o: In function `ssb_ohci_probe':
 ohci-hcd.c:(.text+0xbff39): undefined reference to `ssb_device_enable'
 ohci-hcd.c:(.text+0xbff6f): undefined reference to `ssb_admatch_base'
 ohci-hcd.c:(.text+0xbff8b): undefined reference to `ssb_admatch_size'
 ohci-hcd.c:(.text+0xbffe5): undefined reference to `ssb_device_disable'
 [...]

the reason was that this Kconfig combination was allowed:

 CONFIG_SSB=m
 CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_SSB=y

the fix is to require a modular USB_OHCI_HCD build when SSB is modular.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1003) changes uhci-hcd to treat the URB_ISO_ASAP flag
the same as other host controller drivers, namely, to schedule an Iso
URB for the first available time slot that hasn't already expired.
URBs in which the flag isn't set will be scheduled for the first slot
following the last URB, even if it has expired.

This fixes a problem reported by Martin Bachem.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NAdrian Bunk <bunk@kernel.org>

Found these while looking at printk uses.

Add missing newlines to dev_<level> uses
Add missing KERN_<level> prefixes to multiline dev_<level>s
Fixed a wierd->weird spelling typo
Added a newline to a printk
Signed-off-by: NJoe Perches <joe@perches.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Greg KH <greg@kroah.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: James Smart <James.Smart@Emulex.Com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ohci_bus_{suspend,resume} exists only if we have CONFIG_PM; do the same
thing as other subdrivers...
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order.  If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused.  The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds SSB bus glue for the USB OHCI HCD. 
Signed-off-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleanup: references to two PM routines (and HCD entry points)
that no longer exist are swapped with their replacements.

Evidently au1xxx and ppc-soc EHCI support doesn't get compiled
with power management very much, or these build bugs would have
been patched long ago.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add OHCI big endian frame_no quirk.  The frame_no value stored in the
HCCA is a 16 bit field at a specific offset, but since not all CPUs can
do 16-bit memory accesses it's used as a 32 bit field.  And that's why
big-endian OHCI must shift 16 bits ... unless the spec is not followed.

Currently there's one MPC52xx platform that doesn't need the shift. This
patch adds a new "big endian frame_no" quirk to control that at runtime.
Signed-off-by: NValentine Barshak <vbarshak@ru.mvista.com>
Acked-by: NDale Farnsworth <dale@farnsworth.org>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that accessed register of this controller after
having called iounmap().
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that does not work in the big endian machine.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fixed the problem that does not work in the case of bRequest = 0x05 in
Class or Vendor Request.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The ELAN U132 Host Controller Driver uses the semaphore sw_lock as
mutex. Use the mutex API instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator.  Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as977) reorganizes the way r8a66597-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

Parts of this patch were written by Yoshihiro Shimoda.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as976) reorganizes the way sl811-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

The patch also improves the handling of faults during the status stage
of a control transfer, since it no longer needs to retain the error
information from the earlier stages.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as975) reorganizes the way ohci-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as974) reorganizes the way ehci-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

The patch also simplifies the handling of -EREMOTEIO, since the only
use of that code is to set the do_status flag.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as972) changes ohci-hcd so that after an error occurs, the
remaining TDs for the URB will be skipped over entirely instead of
going through the donelist.  This enables the driver to give back the
URB as soon as the error is detected, avoiding the need to store the
error status in urb->status.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more.  To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses.  The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.

By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (968) changes the way uhci-hcd reports status for
Isochronous URBs.  Until now urb->status has been set to the last
detected error code.  But other HCDs don't do this; they leave the
status set to 0 and report errors only in the individual iso packet
descriptors.  So this patch removes the extra computation and makes
uhci-hcd behave like the others.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as967) makes a few relatively minor changes to the
r8a66597 driver:

	finish_request() does nothing but call done(), so merge the
	two routines.

	Detect and report -EOVERFLOW errors.

	Fix the calculation that checks for short packets.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

It is not necessary to powerdown the ports on ehci_pci_reinit() when the
chip reset already did that.  Removing this saves 20ms during restart
after poweroff paths (which OLPC uses a lot).

To ensure driver startup then behaves consistently, force a reset during
driver startup.  (Not doing this was an accident of some previous changes
to the init sequence.)

Make the corresponding change in the PS3 support.  It's not clear what
ehci-fsl should do here; it has similar code to the PS3.
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Cc: <rvinson@mvista.com>
Acked-by: NGeoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>