Now that the LE L2CAP Connection Oriented Channel support has undergone a
decent amount of testing we can make it officially supported. This patch
removes the enable_lecoc module parameter which was previously needed to
enable support for LE L2CAP CoC.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Now that ATT sockets have been converted to use the new L2CAP_CHAN_FIXED
type there is no need to have an extra check for chan->psm in the
l2cap_chan_close function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The sport variable is used to track the allocation of the local PSM
database to ensure no two sockets take the same local PSM. It is
acquired upon bind() but needs to be freed up if the socket ends up
becoming a client one. This patch adds the clearing of the value when
l2cap_chan_connect is called.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The L2CAP specification requires us to disconnect an L2CAP channel if
the remote side gives us credits beyond 65535. This patch makes sure we
disconnect the channel in such a situation.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The L2CAP specification requires us to disconnect a channel if the
remote device sends us data when it doesn't have any credits to do so.
This patch makes sure that we send the appropriate L2CAP Disconnect
request in this situation.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There's a le_default_mps variable that can be modified through debugfs
but it was never actually used for determining our MPS value. This patch
fixes the MPS initialization to use the variable instead of a fixed
value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Fixed channels have the same source and destination CID. Ensure that the
values get properly initialized when receiving incoming connections and
deriving values from the parent socket.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

ATT channels are not connection oriented so having them use
L2CAP_CHAN_CONN_ORIENTED is quite confusing. Instead, use the new
L2CAP_CHAN_FIXED type and ensure that the MTU and CID values get
properly set.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

There's no reason why A2MP should need or deserve its on channel type.
Instead we should be able to group all fixed CID users under a single
channel type and reuse as much code as possible for them. Where CID
specific exceptions are needed the chan-scid value can be used.

This patch renames the current A2MP channel type to a generic one and
thereby paves the way to allow converting ATT and SMP (and any future
fixed channel protocols) to use the new channel type.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The only user of l2cap_seq_list_remove() was l2cap_seq_list_pop() which
only removes the head, meaning only the "else if (seq_list->head ==
seq)" branch was ever being used. This patch moves the code from this
branch straight into l2cap_seq_list_pop() and removes the (now useless)
l2cap_seq_list_remove().
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds a queue for incoming L2CAP data that's received before
l2cap_connect_cfm is called and processes the data once
l2cap_connect_cfm is called. This way we ensure that we have e.g. all
remote features before processing L2CAP signaling data (which is very
important for making the correct security decisions).

The processing of the pending rx data needs to be done through
queue_work since unlike l2cap_recv_acldata, l2cap_connect_cfm is called
with the hci_dev lock held which could cause potential deadlocks.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch moves the l2cap_conn_add, is_valid_psm and l2cap_chan_connect
functions further down in l2cap_core.c. The patch doesn't contain
anything else except the relocation of these functions. By moving the
functions further down the patch enables a subsequent patch that adds a
pending RX queue to be implemented without a forward declaration of a
function.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With the introduction of security level 4, the L2CAP sockets need to
be made aware of this new level. This change ensures that the pairing
requirements are set correctly for these connections.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

This is initial version of
http://tools.ietf.org/html/draft-ietf-6lo-btle-00

By default the 6LoWPAN support is not activated and user
needs to tweak /sys/kernel/debug/bluetooth/hci0/6lowpan
file.

The kernel needs IPv6 support before 6LoWPAN is usable.
Signed-off-by: NJukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If we receive an L2CAP command reject message over LE we should take
appropriate action on the corresponding channel. This is particularly
important when trying to interact with a remote pre-4.1 system using LE
CoC signaling messages. If we don't react to the command reject the
corresponding socket would not be notified until a connection timeout
occurs.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The range of valid LE PSMs is 0x0001-0x00ff so the check should be for
"less than or equal to" instead of "less than".
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since there's a nice convenient helper for calculating the minimum of
two values, let's use that one.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The values in l2cap_chan that are used for actually transmitting data
only need to be initialized right after we've received an L2CAP Connect
Request or just before we send one. The only thing that we need to
initialize though bind() and connect() is the chan->mode value. This way
all other initializations can be done in the l2cap_le_flowctl_init
function (which now becomes private to l2cap_core.c) and the
l2cap_le_flowctl_start function can be completely removed.

Also, since the l2cap_sock_init function initializes the imtu and omtu
to adequate values these do not need to be part of l2cap_le_flowctl_init.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds entries to debugfs to control the values used for the
MPS and Credits for LE Flow Control Mode.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

LE PSM values have different ranges than those for BR/EDR. The valid
ranges for fixed, SIG assigned values is 0x0001-0x007f and for dynamic
PSM values 0x0080-0x00ff. We need to ensure that bind() and connect()
calls conform to these ranges when operating on LE CoC sockets.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

LE CoC used differend CIC ranges than BR/EDR L2CAP. The start of the
range is the same (0x0040) but the range ends at 0x007f (unlike BR/EDR
where it goes all the way to 0xffff).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The outgoing MTU should only be set upon channel creation to the initial
minimum value (23) or from a remote connect req/rsp PDU.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

It doesn't make sense to have an MPS value greater than the configured
MTU value since we will then not be able to fill up the packets to their
full possible size. We need to set the MPS both in flowctl_init()
as well as flowctl_start() since the imtu may change after init() but
start() is only called after we've sent the LE Connection Request PDU
which depends on having a valid MPS value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

If the peer gives us zero credits in its connection request or response
we must call the suspend channel callback so the BT_SK_SUSPEND flag gets
set and user space is blocked from sending data to the socket.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Unlike BR/EDR, for LE when we're in the BT_CONNECT state we may or may
not have already have sent the Connect Request. This means that we need
some extra tracking of the request. This patch adds an extra channel
flag to prevent the request from being sent a second time.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

When receiving fragments over an LE Connection oriented Channel they
need to be collected up and eventually merged into a single SDU. This
patch adds the necessary code for collecting up the fragment skbs to the
channel context and passing them to the recv() callback when the entire
SDU has been received.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds segmentation support for outgoing data packets. Packets
are segmented based on the MTU and MPS values. The l2cap_chan struct
already contains many helpful variables from BR/EDR Enhanced L2CAP which
can be used for this.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Since LE CoC support needs to be enabled through a module option for now
we need to reject any related signaling PDUs in addition to rejecting
the creation of LE CoC sockets (which we already do).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary discipline for reacting to LE L2CAP
Credits packets, sending those packets, and modifying the known credits
accordingly.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We should return credits to the remote side whenever they fall below a
certain level (in our case under half of the initially given amount).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds tracking of L2CAP connection oriented channel local and
remote credits to struct l2cap_chan and ensures that connect requests
and responses contain the right values.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LE connection oriented channels have their own mode with its own
data transfer rules. In order to implement this properly we need to
distinguish L2CAP channels operating in this mode from other modes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch makes the error handling and return logic of l2cap_le_sig_cmd
consistent with its BR/EDR counterpart.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The normal L2CAP Disconnect request and response are also used for LE
connection oriented channels. Therefore, we can simply use the existing
handler functions for terminating LE based L2CAP channels.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Sending of the L2CAP Disconnect request should also be performed for LE
based channels. The proper thing to do is therefore to look at whether
there's a PSM specified for the channel instead of looking at the link
type.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary boiler plate code to handle receiving
L2CAP connect requests over LE and respond to them with a proper connect
response.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We'll need to have a separate code path for LE based connection
rejection so it's cleaner to move out the response construction code
into its own function (and later a second one for LE).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary code to send an LE L2CAP Connect Request
and handle its response when user space has provided us with an LE
socket with a PSM instead of a fixed CID.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Once connection oriented L2CAP channels over LE are supported they will
need a completely separate handling from BR/EDR channels.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LE signaling PDU length is already calculated in the
l2cap_le_sig_channel function so we can just pass the value to the
various handler functions to avoid unnecessary recalculations (byte
order conversions). Right now the only user is the connection parameter
update procedure, but as new LE signaling operations become available
(for connection oriented channels) they will also be able to make use of
the value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>