If monitor interface is enabled in co-exist mode, only local traffic are
captured. It's caused by missing monitor vdev in co-exist mode. So,
monitor mode clean up is done with separate Monitor APIs. For this,
introduce flags monitor_started and monitor_vdev_created.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: NMiles Hu <milehu@codeaurora.org>
Signed-off-by: NMiles Hu <milehu@codeaurora.org>
Co-developed-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NSeevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-4-jouni@codeaurora.org

Add separate APIs for monitor_vdev_create/monitor_vdev_delete
and monitor_vdev_start/monitor_vdev_stop.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: NMiles Hu <milehu@codeaurora.org>
Signed-off-by: NMiles Hu <milehu@codeaurora.org>
Co-developed-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: NSeevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-3-jouni@codeaurora.org

In 4addr, AP wired backbone to STA wired backbone ping fails due to ARP
request not getting answered. Here 4addr ARP multicast packet is sent in
3addr, so that 4addr STA not honouring the 3addr ARP multicast packet.
Fix this issue by sending out multicast packet in 4addr format, firmware
expects peer meta flag instead of vdev meta flag in Tx descriptor.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01641-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-2-jouni@codeaurora.org

Ath11k FW requires peer parameter WMI_PEER_USE_4ADDR to be set for
4-addr peers allowing 4-address frame transmission to those peers.

Add ath11k driver callback for sta_set_4addr() to queue new workq
set_4addr_wk only once based on new boolean, use_4addr_set.

sta_set_4addr() will be called during 4-addr STA association cases
applicable for both AP and STA modes.

In ath11k_sta_set_4addr_wk(),

AP mode:
        WMI_PEER_USE_4ADDR will be set for the corresponding
        associated 4-addr STA(s)

STA mode:
        WMI_PEER_USE_4ADDR will be set for the AP to which the
        4-addr STA got associated.

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-1
Signed-off-by: NSathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-1-jouni@codeaurora.org

This patch is to add support for WCN6855. For station mode,
WCN6855 is able to connect to an AP, and ping works well.
For AP mode, hostapd is able to bringup an SAP interface with
WCN6855, a normal station can connect to this AP and
ping works well.

Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NBaochen Qiang <bqiang@codeaurora.org>
Signed-off-by: NJouni Malinen <jouni@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210511162214.29475-7-jouni@codeaurora.org

There are multiple occurrances of the misspelling of requeued in
the drivers with symbol names and debug text. Fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210423134133.339751-1-colin.king@canonical.com

When AP goes down without any indication to STA, firmware detects
missing beacon, and sends wmi roam event with reason BEACON_MISS
to the host.

Added support for STA mode to trigger disassociation from AP,
on receiving this event from firmware.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01717-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NLavanya Suresh <lavaks@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1614340859-28867-1-git-send-email-lavaks@codeaurora.org

Define host CE configuration for QCN9074 since the max CE count is six.
Available MSI interrupt is five so cannot able to map the ce_id directly
for the msi_data_idx. Added get_ce_msi_idx ops in ath11k_hif_ops to get
the CE MSI idx which is used to initialize the CE ring.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-10-git-send-email-akolli@codeaurora.org

Three window slots can be configure. First window slot
dedicate for dynamic selection and remaining two slots
dedicate for static selection. To optimise the window
selection, frequent registers (UMAC, CE) are configure
in static window slot. so that we minimise the window
selection. Other registers are configure in dynamic window
slot. Get the window start address from the respective
offset and access the read/write register.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-7-git-send-email-akolli@codeaurora.org

Add MHI config for QCN9074 also populate ath11k_hw_params for QCN9074.

Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-6-git-send-email-akolli@codeaurora.org

Tx descriptor search index field should be updated with hw peer id
and not by AST Hash as per the HW/FW recommendation. Incorrect search
index causes throughput degradation in all scenario for all the
platforms. so updated the search index field with hw peer id, which
is a common change applicable for all the platforms. Also no need of these
configuration for non station type. seen 10% throughput increase in WDS
traffic with this change.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612410960-9120-1-git-send-email-periyasa@codeaurora.org

Removed the duplicated peer related function declaration
from core.h since those functions are already declared in peer.h

Founded in code review.

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: NKarthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1608304793-20612-1-git-send-email-periyasa@codeaurora.org

Now that all the needed pieces are in place implement suspend support QCA6390
PCI devices. All other devices will return -EOPNOTSUPP during suspend. The
suspend is implemented by switching the firmware to WoW mode during suspend, so
the firmware will be running on low power mode while host is in suspend.

At the moment we are not able to shutdown and fully power off the device due to
bugs in MHI subsystem, so WoW mode is a workaround for the time being.

During suspend we enable WoW mode, disable CE irq and DP irq, then put MHI to
suspend state.  During resume, driver resumes MHI firstly, then enables CE irq
and dp IRQ, and sends WoW wakeup command to firmware.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-11-git-send-email-kvalo@codeaurora.org

Implement wow enable ane wow wakeup commands which are needed for suspend.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-9-git-send-email-kvalo@codeaurora.org

When ath11k sends suspend command to firmware, firmware will
return suspend_complete events and add handlers for those.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1607708150-21066-6-git-send-email-kvalo@codeaurora.org

QMI sequence fails if caldata file is not available.
It is observed that 'rmmod ath11k' fails if qmi message fails.
With this patch rmmod/insmod is working.

Logs:
Direct firmware load for IPQ8074/caldata.bin failed with error -2
Falling back to user helper
qmi failed to load CAL: IPQ8074/caldata.bin
qmi failed to load board data file:-11

Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01699-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1606916215-24643-1-git-send-email-akolli@codeaurora.org

It is rather easy to add more entries to ath11k_skb_cb while forgetting the
size limit of ieee80211_tx_info->driver_data. So just check this during the
build to reduce the change of accidental buffer overflow in the skbuff->cb.
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-3-sven@narfation.org

The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.

But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a

  ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0

or (slightly worse) in a kernel oops.

Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.

Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2

Fixes: d5c65159 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org

Unused structure ath11k_vdev_stop_status is removed.
'ath11k_mac_get_ar_vdev_stop_status' api has been replaced
with 'ath11k_mac_get_ar_by_vdev_id' inside vdev_stopped_event.
Signed-off-by: NRitesh Singh <ritesi@codeaurora.org>
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-4-git-send-email-mkenna@codeaurora.org

Peer creation in firmware fails, if last peer deletion
is still in progress.
Hence, add wait for the event after deleting every peer
from host driver to synchronize with firmware.
Signed-off-by: NRitesh Singh <ritesi@codeaurora.org>
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-3-git-send-email-mkenna@codeaurora.org

When the interface is added immediately after removing the
interface, vdev deletion in firmware might not have been
completed.

Hence, add vdev_delete_resp_event and wait_event_timeout
to synchronize with firmware.
Signed-off-by: NRitesh Singh <ritesi@codeaurora.org>
Signed-off-by: NMaharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1605514143-17652-2-git-send-email-mkenna@codeaurora.org

Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.

Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.

Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1
Signed-off-by: NP Praneesh <ppranees@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org

cold boot calibration is the process to calibrate all the channels
during the boot-up to avoid the calibration delay during the
channel change.
During the boot-up, firmware started in cold boot calibration mode
Firmware calibrate all channels and generate CalDb(DDR).
Subsequent wifi bringup will reuse the same CalDb.
Firmware is restarted in normal mode to continue the normal operation.

caldb memory address send to firmware through the QMI message.Firmware
use this address to store the caldb data and use it until next reboot.

This will give the improvement during the channel change. But it is
increasing the boot-up time(up to 15sec depend on number of radios).
So if the user want to reduce the boot-up time and accepting for channel
change delay, user can disable this feature using the module param
cold_boot_cal=0.

Tested-on: IPQ8074 WLAN.HK.2.4.0.1-01162-QCAHKSWPL_SILICONZ-1
Signed-off-by: NGovindaraj Saminathan <gsamin@codeaurora.org>
Co-developed-by: NSowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: NSowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1602862111-14063-1-git-send-email-ssreeela@codeaurora.org

Board Data File (BDF) is loaded upon driver boot-up procedure. The right
board data file is identified on IPQ6018 using bus, qmi-chip-id and
qmi-board-id.

The problem, however, can occur when the (default) board data file cannot
fulfill with the vendor requirements and it is necessary to use a different
board data file.

This problem was already solved on ath10k by adding a ",variant=.*" at the
end of the board name. The same functionality must also be provided for
ath11k.

The device tree requires an additional string to define the variant name

    wifi@c000000 {
        status = "okay";
        qcom,ath11k-calibration-variant = "Cigtech-WF-188";
    };

This would create the boarddata identifier for the board-2.bin search

 *  bus=ahb,qmi-chip-id=0,qmi-board-id=18,variant=Cigtech-WF-188
Signed-off-by: NSven Eckelmann <sven@narfation.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201015131501.1939685-2-sven@narfation.org

Add packet log support for QCA6390, otherwise the data connection will stall
within a minute or so.  Enable it via debugfs and use trace-cmd to capture the
pktlogs.

echo 0xffff 1 > /sys/kernel/debug/ath11k/qca6390\ hw2.0/mac0/pktlog_filter

The mon status ring doesn't support interrupt so far, so host starts
a timer to reap this ring. The timer handler also reaps the
rxdma_err_dst_ring in case of monitor mode.

As QCA6390 requires bss created ahead of starting vdev, so check
vdev_start_delay for monitor mode.

For QCA6390, it uses wbm_desc_rel_ring to return descriptors.
It also uses rx_refill_buf_ring to fill mon buffer instead of
rxdma_mon_buf_ring.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601463073-12106-2-git-send-email-kvalo@codeaurora.org

IPQ8074 HW uses rproc with AHB as underlying hif layer.
Move rproc references from common core layer to target
hif layer. Remove IS_ENABLED check for CONFIG_REMOTEPROC
as it's not required anymore.

No functional changes. Compile tested only.
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600090615-18904-1-git-send-email-govinds@codeaurora.org

Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.

To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0

To enable software crypto:
insmod ath11k.ko crypto_mode=1

These modes could be helpful in debugging crypto related issues.

Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: NManikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: NVenkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com

IPQ6018 has one 5G and one 2G radio with 2x2,
shares ipq8074 configurations.

Tested on: IPQ6018 hw1.0 AHB WLAN.HK.2.2-02134-QCAHKSWPL_SILICONZ-1
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746cb68b63-c2bc31ec-a31e-442e-a572-26f4c045c06b-000000@us-west-2.amazonses.com

Move target CE config and target CE service config to hw_params.
No functional changes.

Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00009-QCAHKSWPL_SILICONZ-1
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746cb685d9-6bedeccb-29a1-4d32-8664-fcfe7d105f4a-000000@us-west-2.amazonses.com

For QCA6390 firmware, bss peer must be created before vdev_start, so delay
vdev_start until bss peer is created.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-6-git-send-email-kvalo@codeaurora.org

For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.

Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org

For QCA6390, only one pdev is created and only one HW is registered to
mac80211. This one pdev manages both 2G radio and 5G radio.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597576599-8857-10-git-send-email-kvalo@codeaurora.org

PCI devices like QCA6390 load the board file differently, add support for that
and the method is chosen using bus_params variables.

Add support to create board name for different targets.  This board name is
used to parse the board data from board-2.bin for ahb/pci based targets.

As struct target_mem_chunk::vaddr was changed from 'u32' to 'u32 *' in
ath11k_qmi_assign_target_mem_chunk() vaddr assignments were changed to NULL to
avoid a compilation warning. IPQ8074 does not use the vaddr field for anything
so that change does not affect functionality.

At the moment this only supports board files with BIN type. Support for ELF
type, which seems to be more popular on QCA6390 devices, needs to be added later.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-3-git-send-email-kvalo@codeaurora.org

PCI devices like QCA6390 have a separate firmware image for the m3
micro-controller. Add support to load the firmware using m3.bin file.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-2-git-send-email-kvalo@codeaurora.org

QCA6390 and other PCI devices use MHI based firmware loading and do not use
remoteproc, so enable it only for AHB devices.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NGovind Singh <govinds@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-11-git-send-email-kvalo@codeaurora.org

This is needed to initialise hw_params before MHI registration starts. MHI
needs location of firmware directory and that's delivered via hw_params.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-8-git-send-email-kvalo@codeaurora.org

This is needed for splitting ahb and pci modules as they have different ring
mask settings.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-4-git-send-email-kvalo@codeaurora.org

Define own firmware directory and settings for QCA6390.

Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: NCarl Huang <cjhuang@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597309466-19688-3-git-send-email-kvalo@codeaurora.org

The downside of using defines in struct ath11k_hw_params.fw.dir is that it's
easy to get it wrong as the full path is not visible. So drop the use of
defines and instead create the patch runtime using a static inline function
ath11k_core_create_firmware_path(). Hopefully this reduces the chances of using
incorrect firmware path.

No functional changes. Compile tested only.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-8-git-send-email-kvalo@codeaurora.org

To avoid duplicating the logic how the full firmware path is created create a
common function ath11k_core_firmware_request() and convert also qmi.c to use it.

Also remove a useless info print, it's more like a debug message anyway.

No functional changes. Compile tested only.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1592316055-24958-7-git-send-email-kvalo@codeaurora.org