Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current driver is assuming that SSI id = SCU id.
But, now, it can get correct SSI/SCU from
rsnd_dai_stream. use it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

struct rsnd_dai_stream used list for mod list.
It added only odd flexibility to current driver, and
it is a factor which makes extendibility difficult.
rsnd use mod array instead of list from now.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd SSIU/SSI/SCU/SRU path is set
when playback/capture starts up.
But it is meaningless method, since the path is based
on platform and can be set in probe() timing.
This patch sets the path on probe() timing.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

struct rsnd_dai is called as "rdai",
but its size has been called as "dai_nr".
Unify these as "rdai"
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

priv has rcar_snd_info pointer.
having priv and info in same time is verbose.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

core.c is the only user of rsnd_mod_call() macro.
Move it to core.c from rsnd.h
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

DIV_EN register enable bit is required when you use Gen2 SRC
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current for_each_rsnd_xxx macro will read out-of-array's
memory after last loop operation.
It was not good C language operation, and the binary which was
compiled by (at least) gcc 4.8.1 is broken
This patch tidyup these issues
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound Gen2 has SRC (= Sampling Rate Converter)
which needs 2 DMAC.
The data path image when you use SRC on Gen2 is

[mem] -> Audio-DMAC -> SRC -> Audio-DMAC-peri-peri -> SSIU -> SSI

This patch support SRC and DMAEnine.
It is tested on R-Car H2 Lager board
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas Gen2 sound will use 2 DMAC
which are Audio-DMAC, and Audio-DMAC-peri-peri.
Current driver has callback function for each DMAC,
because it assumed each DMAC needs special settings.
But it became clear that these can share settings.
This patch removes unnecessary callback
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound IP Gen1/Gen2 are similar, but different.
This patch extracts Gen1/Gen2 common and dependency parts,
and create Gen1/Gen2 ops to control it.

According to this structure, SSIU setup which
has been implemented on ssi.c can be moved to scu.c
(SRU/SSIU/SCU should be implemented on scu.c)
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SCU needs SSI direction if Gen2.
Add rsnd_ssi_is_play() function for it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SRC clock and timing setting register
exist in SRU and ADG on Gen1.
But, these are merged into ADG on Gen2.
Current driver is supporting Gen1 SRC only
at this point, but, above settings are
set as different function.
This patch merges these as preparation of Gen2 support.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_scu_hpbif_is_enable() is used only scu.c now.
It can be local macro
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

*priv pointer exists under rsnd_mod,
and, it can get rsnd_mod pointer from rsnd_dma.
remove duplicate rsnd_dma :: priv
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, SSI_MODE0/1 are controlled under scu.c
ssiu is no longer needed on ssi.c
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SRU (Gen1) / SCU (Gen2) / SSIU (Gen2) are controlled under scu.c.
(SCU + SSIU (Gen2) was SRU (Gen1))
And register of SSI_MODE0/1 are mapped on these IP.
But these have been implemented under ssi.c on this driver.
The naming is very confusable,
but it should be implemented under scu.c
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd driver is using ssi local
rsnd_rdai_is_clk_master() for checking clock master.
But it can be rsnd_dai_is_clk_master(), and share in each file
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

rsnd_mod debug information is implemented
in each callback functions now.
But, it can be implemented in rsnd_mod_call(),
and share this code.
This patch adds it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Gen1:SRU has only 1 BUSIF_MODE,
but Gen2:SSIU/SCU has SRCm_BUSIF_MODE, and SSIn_BUSIF_MODE.
This patch rename current BUSIF_MODE to SRC_BUSIF_MODE.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds SRC support to Renesas sound driver.
SRC converts sampling rate between codec <-> cpu.
It needs special codec chip,
or very simple DA/AD converter to use it.
This patch was tested via ak4554 codec,
and supports Gen1 only at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

INT_ENABLE is needed only Gen2.
rsnd_mod_write() do nothing on Gen1, but it is confusable.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound has SRC (= Sampling Rate Converter),
but, the HW implementation depends on its generation.
It was part of SRU on Gen1, and SCU on Gen2.
This SCU needs DMA transfer to use it.
Current rsnd driver is using it as DMA transfer buffer
(= no rate convert), and Gen1 is only supported at this point.

This patch cleanup it with focusing about SRC and Gen2 part.

rsnd_scu_set_route() is needed only Gen1.

This patch renames it to rsnd_scu_set_route_if_gen1()
and it adds comment to rsnd_reg member
in order to clarify it is used for Gen1.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Use correct register name which appears in the datasheet
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds Gen2 sound support for Renesas R-Car.
But, it is supporting PIO transfer only at this point
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

AUDIO_CLK_SEL4/5 are not used
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Because these are signed they can either be 0 or -1 instead of 0 and 1
as intended.  It doesn't cause a problem from what I can see, but it's
dangerous and Sparse complains:

	sound/soc/sh/rcar/rsnd.h:177:25:
		error: dubious one-bit signed bitfield
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current SSI needs RSND_SSI_DEPENDENT flag to
decide dependent/independent mode.
And SCU needs RSND_SCU_USE_HPBIF flag
to decide HPBIF is enable/disable.
But these 2 means same things.

This patch adds new rsnd_scu_hpbif_is_enable()
function, and merges above methods.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rcar is using rsnd_is_gen1/gen2() to checking its
IP generation, but it needs data mask.
This patch fixes it up.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

adg.c only used rsnd_priv_read/write/bset()
which is the only user of NULL mod.
but, it can be removed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds BUSIF support for R-Car sound DMAEngine transfer.
The sound data will be transferred via FIFO which can cover blank time
which will happen when DMA channel is switching.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car Sound driver will support DMA transfer in the future,
then, SSI/SRU/SRC will use it.
Current R-Car can't use soc-dmaengine-pcm.c since its DMAEngine
doesn't support dmaengine_prep_dma_cyclic(),
and SSI needs double plane transfer (which needs special submit) on DMAC.
This patch adds common DMAEngine method for it
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd driver is using struct rsnd_dai_platform_info
so that indicate sound DAI information (playback/capture SSI ID).
But, SSI settings were also required separately.
Thus, platform settings was very un-understandable.
This patch adds dai_id to SSI
settings, and removed rsnd_dai_platform_info.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)

As 1st protype, this patch adds SSI feature on this driver.
But, it is PIO sound playback support only at this point.
The DMA transfer, and capture feature will be supported in the future
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)

This patch adds ADG feature which controls sound clock
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)

This patch adds SCU feature on this driver.
But, it defines SCU style only, does nothing at this point.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)

The main difference between Gen1 and Gen2 are
1) register offset, 2) data path

In order to control Gen1/Gen2 by same method,
this patch adds gen.c.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuit is different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2)
(Actually, there are many difference in Generation1 chips)

Gen1 series consists of SRU/SSI/ADG, and
Gen2 series consists of SCU/SSIU/SSI/ADG.

In order to control these by same method,
these are treated as "mod" on this driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas R-Car series sound circuit consists of SSI and its peripheral.
But this peripheral circuits are different between
R-Car Generation1 (E1/M1/H1) and Generation2 (E2/M2/H2).
(Actually, there are many difference in Generation1 chips)

Basically, for the future, Renesas R-Car series will use
Gen2 style sound circuit, but driver should care Gen1 also.
The main differences between Gen1 and Gen2 peripheral
are 1) register offset, 2) data path.

This patch adds basic (core) feature for R-Car
series sound driver as prototype
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>