Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 26 11月, 2018 11 次提交
  3. 25 11月, 2018 18 次提交
  5. 15 11月, 2018 1 次提交
    • N
      powerpc/64: Fix kernel stack 16-byte alignment · 66f93c5a
      由 Nicholas Piggin 提交于 
      Commit 4c2de74c ("powerpc/64: Interrupts save PPR on stack rather
than thread_struct") changed sizeof(struct pt_regs) % 16 from 0 to 8,
which causes the interrupt frame allocation on kernel entry to put the
kernel stack out of alignment.

Quadword (16-byte) alignment for the stack is required by both the
64-bit v1 ABI (v1.9 § 3.2.2) and the 64-bit v2 ABI (v1.1 § 2.2.2.1).

Add a pad field to fix alignment, and add a BUILD_BUG_ON to catch this
in future.

Fixes: 4c2de74c ("powerpc/64: Interrupts save PPR on stack rather than thread_struct")
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      66f93c5a
  7. 14 11月, 2018 1 次提交
  9. 12 11月, 2018 2 次提交
    • M
      powerpc/io: Fix the IO workarounds code to work with Radix · 43c6494f
      由 Michael Ellerman 提交于 
      Back in 2006 Ben added some workarounds for a misbehaviour in the
Spider IO bridge used on early Cell machines, see commit
014da7ff ("[POWERPC] Cell "Spider" MMIO workarounds"). Later these
were made to be generic, ie. not tied specifically to Spider.

The code stashes a token in the high bits (59-48) of virtual addresses
used for IO (eg. returned from ioremap()). This works fine when using
the Hash MMU, but when we're using the Radix MMU the bits used for the
token overlap with some of the bits of the virtual address.

This is because the maximum virtual address is larger with Radix, up
to c00fffffffffffff, and in fact we use that high part of the address
range for ioremap(), see RADIX_KERN_IO_START.

As it happens the bits that are used overlap with the bits that
differentiate an IO address vs a linear map address. If the resulting
address lies outside the linear mapping we will crash (see below), if
not we just corrupt memory.

  virtio-pci 0000:00:00.0: Using 64-bit direct DMA at offset 800000000000000
  Unable to handle kernel paging request for data at address 0xc000000080000014
  ...
  CFAR: c000000000626b98 DAR: c000000080000014 DSISR: 42000000 IRQMASK: 0
  GPR00: c0000000006c54fc c00000003e523378 c0000000016de600 0000000000000000
  GPR04: c00c000080000014 0000000000000007 0fffffff000affff 0000000000000030
         ^^^^
  ...
  NIP [c000000000626c5c] .iowrite8+0xec/0x100
  LR [c0000000006c992c] .vp_reset+0x2c/0x90
  Call Trace:
    .pci_bus_read_config_dword+0xc4/0x120 (unreliable)
    .register_virtio_device+0x13c/0x1c0
    .virtio_pci_probe+0x148/0x1f0
    .local_pci_probe+0x68/0x140
    .pci_device_probe+0x164/0x220
    .really_probe+0x274/0x3b0
    .driver_probe_device+0x80/0x170
    .__driver_attach+0x14c/0x150
    .bus_for_each_dev+0xb8/0x130
    .driver_attach+0x34/0x50
    .bus_add_driver+0x178/0x2f0
    .driver_register+0x90/0x1a0
    .__pci_register_driver+0x6c/0x90
    .virtio_pci_driver_init+0x2c/0x40
    .do_one_initcall+0x64/0x280
    .kernel_init_freeable+0x36c/0x474
    .kernel_init+0x24/0x160
    .ret_from_kernel_thread+0x58/0x7c

This hasn't been a problem because CONFIG_PPC_IO_WORKAROUNDS which
enables this code is usually not enabled. It is only enabled when it's
selected by PPC_CELL_NATIVE which is only selected by
PPC_IBM_CELL_BLADE and that in turn depends on BIG_ENDIAN. So in order
to hit the bug you need to build a big endian kernel, with IBM Cell
Blade support enabled, as well as Radix MMU support, and then boot
that on Power9 using Radix MMU.

Still we can fix the bug, so let's do that. We simply use fewer bits
for the token, taking the union of the restrictions on the address
from both Hash and Radix, we end up with 8 bits we can use for the
token. The only user of the token is iowa_mem_find_bus() which only
supports 8 token values, so 8 bits is plenty for that.

Fixes: 566ca99a ("powerpc/mm/radix: Add dummy radix_enabled()")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      43c6494f
    • M
      powerpc/mm/64s: Fix preempt warning in slb_allocate_kernel() · c8b00bb7
      由 Michael Ellerman 提交于 
      With preempt enabled we see warnings in do_slb_fault():

  BUG: using smp_processor_id() in preemptible [00000000] code: kworker/u33:0/98
  futex hash table entries: 4096 (order: 3, 524288 bytes)
  caller is do_slb_fault+0x204/0x230
  CPU: 5 PID: 98 Comm: kworker/u33:0 Not tainted 4.19.0-rc3-gcc-7.3.1-00022-g1936f094 #138
  Call Trace:
    dump_stack+0xb4/0x104 (unreliable)
    check_preemption_disabled+0x148/0x150
    do_slb_fault+0x204/0x230
    data_access_slb_common+0x138/0x180

This is caused by the get_paca() in slb_allocate_kernel(), which
includes a call to debug_smp_processor_id().

slb_allocate_kernel() can only be called from do_slb_fault(), and in
that path interrupts are hard disabled and so we can't be preempted,
but we can't update the preempt flags (in thread_info) because that
could cause an SLB fault.

So just use local_paca which is safe and doesn't cause the warning.

Fixes: 48e7b769 ("powerpc/64s/hash: Convert SLB miss handlers to C")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      c8b00bb7
  11. 07 11月, 2018 1 次提交
    • S
      KVM: PPC: Move and undef TRACE_INCLUDE_PATH/FILE · 28c5bcf7
      由 Scott Wood 提交于 
      TRACE_INCLUDE_PATH and TRACE_INCLUDE_FILE are used by
<trace/define_trace.h>, so like that #include, they should
be outside #ifdef protection.

They also need to be #undefed before defining, in case multiple trace
headers are included by the same C file.  This became the case on
book3e after commit cf4a6085 ("powerpc/mm: Add missing tracepoint for
tlbie"), leading to the following build error:

   CC      arch/powerpc/kvm/powerpc.o
In file included from arch/powerpc/kvm/powerpc.c:51:0:
arch/powerpc/kvm/trace.h:9:0: error: "TRACE_INCLUDE_PATH" redefined
[-Werror]
  #define TRACE_INCLUDE_PATH .
  ^
In file included from arch/powerpc/kvm/../mm/mmu_decl.h:25:0,
                  from arch/powerpc/kvm/powerpc.c:48:
./arch/powerpc/include/asm/trace.h:224:0: note: this is the location of
the previous definition
  #define TRACE_INCLUDE_PATH asm
  ^
cc1: all warnings being treated as errors
Reported-by: NChristian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: NScott Wood <oss@buserror.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      28c5bcf7
  13. 06 11月, 2018 3 次提交
  15. 05 11月, 2018 1 次提交
    • A
      powerpc/powernv/npu: Remove NPU DMA ops · 3182215d
      由 Alistair Popple 提交于 
      The NPU IOMMU is setup to mirror the parent PCIe device IOMMU
setup. Therefore it does not make sense to call dma operations such as
dma_map_page(), etc. directly on these devices. The existing dma_ops
simply print a warning if they are ever called, however this is
unnecessary and the warnings are likely to go unnoticed.

It is instead simpler to remove these operations and let the generic
DMA code print warnings (eg. via a NULL pointer deref) in cases of
buggy drivers attempting dma operations on NVLink devices.
Signed-off-by: NAlistair Popple <alistair@popple.id.au>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      3182215d
  17. 02 11月, 2018 1 次提交
  19. 01 11月, 2018 1 次提交