Signed-off-by: NRémi Cardona <remi.cardona@smartjog.com>
Reviewed-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Drivers must not rely on cpu_is_omap* macros (they will soon become
private). Use the ISP revision instead to identify the hardware.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Clock enable (disable) is split in two operations, prepare and enable
(disable and unprepare). Perform both when enabling/disabling the ISP
clocks.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Support both grayscale (Y8) and Bayer (SBGGR8, SGBRG8, SGRBG8 and
SRGGB8) formats.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use the dev_* message logging API instead of raw printk.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

No longer assume pad number 0 is the source pad of the external entity. Find
the source pad from the external entity and use it instead.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Configure CSI-2 phy based on platform data in the ISP driver. For that, the
new V4L2_CID_IMAGE_SOURCE_PIXEL_RATE control is used. Previously the same
was configured from the board code.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add PHY routing configuration for both 3430 and 3630. Also add register bit
definitions of CSIRXFE and CAMERA_PHY_CTRL registers on OMAP 3430 and 3630,
respectively.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the registers used to configure the CSI-2 receiver PHY on OMAP3430 and
3630 and map them in the ISP driver. The register is part of the control
block but it only is needed by the ISP driver.
Signed-off-by: NSakari Ailus <sakari.ailus@iki.fi>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The OMAP3ISP_*_REG_OFFSET, OMAP3ISP_*_REG_BASE and OMAP3ISP_*_REG macros
are not needed. Remove them.
The only exception is the OMAP3ISP_HIST_REG_BASE address. Replace it
with the memory address received through platform resources.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 buffers use the monotonic clock, while statistics buffers use wall
time. This makes it difficult to correlate video frames and statistics.
Switch statistics buffers to the monotonic clock to fix this.
Reported-by: NAntoine Reversat <a.reversat@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

V4L2 integer controls are stored in signed 32-bit values. However, UVC
controls can be either signed or unsigned. Take the UVC control
signedness into account when clamping the control value to the min-max
range.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The MEDIA_ENT_FL_DEFAULT identifies entities that are considered as
default for their group and type. For video nodes, it identifies the
node that application should use by default.
UVC devices don't report which output terminal should be considered as
the default, use the first one. Most devices have a single output
terminal anyway.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The proper error code is -ENOTTY instead of -EINVAL.
This issue was found by the v4l2-compliance tool.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Set the capabilities field to global capabilities, and the device_caps
field to the video node capabilities.
This issue was found by the v4l2-compliance tool.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Return the default format in that case.
This issue was found by the v4l2-compliance tool.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The proper return code according to the V4L2 specification is -EACCES,
not -EINVAL.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When one of the requested controls doesn't exist the error_idx field
must reflect that situation. For G_EXT_CTRLS and S_EXT_CTRLS, error_idx
must be set to the control count. For TRY_EXT_CTRLS, it must be set to
the index of the unexisting control.
This issue was found by the v4l2-compliance tool.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This just adds the usbid to the rtl28xxu driver, that's all that's
needed to make the stick work for DVB.
Signed-off-by: NJuergen Lock <nox@jelal.kn-bremen.de>
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It was a bad idea, as comment also says, to write some "don't care"
registers as 0xff value. Fix it.
Signed-off-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds V4L2 driver for Samsung S3C24XX/S3C64XX SoC series
camera interface. The driver exposes a subdev device node for CAMIF
pixel resolution and crop control and two video capture nodes - for
the "codec" and "preview" data paths. It has been tested on Mini2440
(s3c2440) and Mini6410 (s3c6410) board with gstreamer and mplayer.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NTomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: NAndrey Gusakov <dron0gus@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The right solution is to remove the architecture dependency on
dma_common_get_sgtable(). Revert this patch to apply the right one.

This reverts commit 93049b93.

When one input buffer has multiple frames, it should be fed
again to the hardware with the remaining bytes. Removed the
check for P frame in this scenario as this condition can come with
all frame types.
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Signed-off-by: NARUN MANKUZHI <arun.m@samsung.com>
Acked-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Modified the function s5p_mfc_get_dec_y_adr_v6 to access the
decode Y address register instead of display Y address.
Signed-off-by: NSunil Mazhavanchery <sunilm@samsung.com>
Signed-off-by: NArun Kumar K <arun.kk@samsung.com>
Acked-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

vfl_dir should be set to VFL_DIR_M2M so valid ioctls for this
mem-to-mem device can be properly determined in the v4l2 core.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Macros used to set input and output RGB type aren't correct.
Updating the macros as per register manual.
Signed-off-by: NShaik Ameer Basha <shaik.ameer@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this may cause driver resources not to be released.
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this may cause driver resources not to be released.
This patch is required for stable kernels v3.5+.
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Use uninterruptible mutex_lock in the release() file op to make
sure all resources are properly freed when a process is being
terminated. Returning -ERESTARTSYS has no effect for a terminating
process and this caused driver resources not to be released. Not
releasing the buffer queue also prevented other drivers to free
memory, e.g. in MMAP -> USERPTR scenario.
This patch is required for stable kernels v3.6+.
Reported-by: NKamil Debski <k.debski@samsung.com>
Reported-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Make sure when fimc and fimc-lite capture video node is registered
it has valid pipeline_ops assigned to it. Otherwise when a video
node is opened right after is was registered there, might be an
attempt to use ops that are just being assigned, after function
v4l2_device_register_subdev() returns.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

As reported by Stephen:

> After merging the v4l-dvb tree, today's linux-next build (x86_64
> allmodconfig) failed like this:
>
> ERROR: "dma_common_get_sgtable" [drivers/media/v4l2-core/videobuf2-dma-contig.ko] undefined!
>
> Caused by commit 9ef2cbeb ("[media] v4l: vb2-dma-contig: add support
> for DMABUF exporting").  dma_common_get_sgtable() is called from the
> inline dma_get_sgtable_attrs() and dma_get_sgtable_attrs() is "called
> from" dma_get_sgtable().  dma_common_get_sgtable() is only defined if
> ARCH_HAS_DMA_DECLARE_COHERENT_MEMORY is set which depends on
> CONFIG_HAVE_GENERIC_DMA_COHERENT being set which it isn't for this build.

The simplest fix is to just not support DMABUF with vb2-contig, on archs
where this symbol doesn't exist. Some latter patch can rewrite it to
support this outside -arm.
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch enhances s5p-mfc with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch enhances s5p-tv with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch enhances s5p-fimc with support for DMABUF exporting via
VIDIOC_EXPBUF ioctl.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Most operations on DMA and DMABUF framework require the size of a buffer to be
page aligned. This patch guarantees the requirement is satisfied for all
vb2-dma-contig buffers.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The DMA transfer must be aligned to a specific value. If userptr is not aligned
to DMA requirements then unexpected corruptions of the memory may occur before
or after a buffer.  To prevent such situations, all unligned userptr buffers
are rejected at VIDIOC_QBUF.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds taking reference to the device for MMAP buffers.
Such buffers, may be exported using DMABUF mechanism. If the driver that
created a queue is unloaded then the queue is released, the device might be
released too.  However, buffers cannot be released if they are referenced by
DMABUF descriptor(s). The device pointer kept in a buffer must be valid for the
whole buffer's lifetime. Therefore MMAP buffers should take a reference to the
device to avoid risk of dangling pointers.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds support for exporting a dma-contig buffer using
DMABUF interface.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds extension to videobuf2-core. It allow to export an mmap buffer
as a DMABUF file descriptor.
Signed-off-by: NTomasz Stanislawski <t.stanislaws@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Tested-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>