Cadence I2C controller has bug wherein it generates invalid read transactions
after timeout in master receiver mode. This driver does not use the HW
timeout and this interrupt is disabled but the feature itself cannot be
disabled. Hence, this patch writes the maximum value (0xFF) to this register.
This is one of the workarounds to this bug and it will not avoid the issue
completely but reduces the chances of error.
Signed-off-by: NVishnu Motghare <vishnum@xilinx.com>
Signed-off-by: NHarini Katakam <harinik@xilinx.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

According to I2C specification the NACK should be handled as follows:
"When SDA remains HIGH during this ninth clock pulse, this is defined as the Not
Acknowledge signal. The master can then generate either a STOP condition to
abort the transfer, or a repeated START condition to start a new transfer."
[I2C spec Rev. 6, 3.1.6: http://www.nxp.com/documents/user_manual/UM10204.pdf]

Currently the Davinci i2c driver interrupts the transfer on receipt of a
NACK but fails to send a STOP in some situations and so makes the bus
stuck until next I2C IP reset (idle/enable).

For example, the issue will happen during SMBus read transfer which
consists from two i2c messages write command/address and read data:

S Slave Address Wr A Command Code A Sr Slave Address Rd A D1..Dn A P
<--- write -----------------------> <--- read --------------------->

The I2C client device will send NACK if it can't recognize "Command Code"
and it's expected from I2C master to generate STP in this case.
But now, Davinci i2C driver will just exit with -EREMOTEIO and STP will
not be generated.

Hence, fix it by generating Stop condition (STP) always when NACK is received.

This patch fixes Davinci I2C in the same way it was done for OMAP I2C
commit cda2109a ("i2c: omap: query STP always when NACK is received").
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NHein Tibosch <hein_tibosch@yahoo.es>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NWolfram Sang <wsa@the-dreams.de>
Cc: stable@kernel.org

It appears that some SCHEDULE_USER (asm for schedule_user) callers
in arch/x86/kernel/entry_64.S are called from RCU kernel context,
and schedule_user will return in RCU user context.  This causes RCU
warnings and possible failures.

This is intended to be a minimal fix suitable for 3.18.
Reported-and-tested-by: NDave Jones <davej@redhat.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Frédéric Weisbecker <fweisbec@gmail.com>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NAndy Lutomirski <luto@amacapital.net>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull i2c bugfixes from Wolfram Sang:
 "A few driver bugfixes for 3.18"

* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: omap: fix i207 errata handling
  i2c: designware: prevent early stop on TX FIFO empty
  i2c: omap: fix NACK and Arbitration Lost irq handling

Pull PCI fix from Bjorn Helgaas:
 "This fixes a Tegra20 regression that we introduced during the v3.18
  merge window"

* tag 'pci-v3.18-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  PCI: tegra: Use physical range for I/O mapping

Pull devicetree bugfix from Grant Likely:
 "One more bug fix for v3.18.  I debated whether or not to send you this
  merge request because we're at such a late rc.  The bug isn't critical
  in that there is only one system known to be affected and the patch is
  easy to backport.  The codepath is used by pretty much every DT based
  system, so there is risk a of regression (it /should/ be safe, but
  I've been bitten by stuff that should be safe before).  I've had it in
  linux-next for a week and haven't received any complaints.

  I think it probably should just be merged right away rather than
  waiting for the merge window and backporting.  It does fix a real bug
  and the code is theoretically safer after the change.  I can't think
  of any situation where it would be dangerous to reserve the DT memory
  an extra time.

  Summary from tag:

    Single bugfix for boot failure seen in the wild.  The memory reserve
    code tries to be clever about reserving the FDT, but it should just
    go ahead and reserve it unconditionally to avoid the problem of
    partial overlap described in the patch"

* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
  of/fdt: memblock_reserve /memreserve/ regions in the case of partial overlap

Pull block core regression fix from Jens Axboe:
 "Single fix for a regression introduced in this development cycle,
  where dm on top of dif/dix is broken.  From Darrick Wong"

* 'for-linus' of git://git.kernel.dk/linux-block:
  block: fix regression where bio_integrity_process uses wrong bio_vec iterator

Pull drm fixes from Dave Airlie:
 "Radeon and Nouveau fixes:

  So nouveau had a few regression introduced, Ben and Maarten finally
  tracked down the one that was causing problems on my MacBookPro, also
  nvidia gave some info on the an engine we were using incorrectly, so
  disable our use of it, and one regresion with pci hotplug affecting
  optimus users.

  Radeon has an oops fixs, sync fix, and one workaround to avoid broken
  functionality on 32-bit x86, this needs better root causing and a
  better fix, but the bandaid is a lot safer at this point"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
  drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
  drm/radeon: sync all BOs involved in a CS v2
  nouveau: move the hotplug ignore to correct place.
  drm/nouveau/gf116: remove copy1 engine
  drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
  drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it

Pull networking fixes from David Miller:

 1) Fill in ethtool link parameters for all link types in cxgb4, from
    Hariprasad Shenai.

 2) Fix probe regressions in stmmac driver, from Huacai Chen.

 3) Network namespace leaks on errirs in rtnetlink, from Nicolas
    Dichtel.

 4) Remove erroneous BUG check which can actually trigger legitimately,
    in xen-netfront.  From Seth Forshee.

 5) Validate length of IFLA_BOND_ARP_IP_TARGET netlink attributes, from
    Thomas Grag.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  cxgb4: Fill in supported link mode for SFP modules
  xen-netfront: Remove BUGs on paged skb data which crosses a page boundary
  sh_eth: Fix sleeping function called from invalid context
  stmmac: platform: Move plat_dat checking earlier
  sh_eth: Fix skb alloc size and alignment adjust rule.
  rtnetlink: release net refcnt on error in do_setlink()
  bond: Check length of IFLA_BOND_ARP_IP_TARGET attributes

Pull keyring/nfs fixes from James Morris:
 "From David Howells:

  The first one fixes the handling of maximum buffer size for key
  descriptions, fixing the size at 4095 + NUL char rather than whatever
  PAGE_SIZE happens to be and permits you to read back the full
  description without it getting clipped because some extra information
  got prepended.

  The second and third fix a bug in NFS idmapper handling whereby a key
  representing a mapping between an id and a name expires and causing
  EKEYEXPIRED to be seen internally in NFS (which prevents the mapping
  from happening) rather than re-looking up the mapping"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  KEYS: request_key() should reget expired keys rather than give EKEYEXPIRED
  KEYS: Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags
  KEYS: Fix the size of the key description passed to/from userspace

Merge misc fixes from Andrew Morton:
 "10 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  slab: fix nodeid bounds check for non-contiguous node IDs
  lib/genalloc.c: export devm_gen_pool_create() for modules
  mm: fix anon_vma_clone() error treatment
  mm: fix swapoff hang after page migration and fork
  fat: fix oops on corrupted vfat fs
  ipc/sem.c: fully initialize sem_array before making it visible
  drivers/input/evdev.c: don't kfree() a vmalloc address
  mm/vmpressure.c: fix race in vmpressure_work_fn()
  mm: frontswap: invalidate expired data on a dup-store failure
  mm: do not overwrite reserved pages counter at show_mem()

The bounds check for nodeid in ____cache_alloc_node gives false
positives on machines where the node IDs are not contiguous, leading to
a panic at boot time.  For example, on a POWER8 machine the node IDs are
typically 0, 1, 16 and 17.  This means that num_online_nodes() returns
4, so when ____cache_alloc_node is called with nodeid = 16 the VM_BUG_ON
triggers, like this:

  kernel BUG at /home/paulus/kernel/kvm/mm/slab.c:3079!
  Call Trace:
    .____cache_alloc_node+0x5c/0x270 (unreliable)
    .kmem_cache_alloc_node_trace+0xdc/0x360
    .init_list+0x3c/0x128
    .kmem_cache_init+0x1dc/0x258
    .start_kernel+0x2a0/0x568
    start_here_common+0x20/0xa8

To fix this, we instead compare the nodeid with MAX_NUMNODES, and
additionally make sure it isn't negative (since nodeid is an int).  The
check is there mainly to protect the array dereference in the get_node()
call in the next line, and the array being dereferenced is of size
MAX_NUMNODES.  If the nodeid is in range but invalid (for example if the
node is off-line), the BUG_ON in the next line will catch that.

Fixes: 14e50c6a ("mm: slab: Verify the nodeid passed to ____cache_alloc_node")
Signed-off-by: NPaul Mackerras <paulus@samba.org>
Reviewed-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: NPekka Enberg <penberg@kernel.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Modules can use this function for creating pool.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: Laura Abbott <lauraa@codeaurora.org>
Cc: Olof Johansson <olof@lixom.net>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Andrew Morton noticed that the error return from anon_vma_clone() was
being dropped and replaced with -ENOMEM (which is not itself a bug
because the only error return value from anon_vma_clone() is -ENOMEM).

I did an audit of callers of anon_vma_clone() and discovered an actual
bug where the error return was being lost.  In __split_vma(), between
Linux 3.11 and 3.12 the code was changed so the err variable is used
before the call to anon_vma_clone() and the default initial value of
-ENOMEM is overwritten.  So a failure of anon_vma_clone() will return
success since err at this point is now zero.

Below is a patch which fixes this bug and also propagates the error
return value from anon_vma_clone() in all cases.

Fixes: ef0855d3 ("mm: mempolicy: turn vma_set_policy() into vma_dup_policy()")
Signed-off-by: NDaniel Forrest <dan.forrest@ssec.wisc.edu>
Reviewed-by: NMichal Hocko <mhocko@suse.cz>
Cc: Konstantin Khlebnikov <koct9i@gmail.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Tim Hartrick <tim@edgecast.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Michel Lespinasse <walken@google.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: <stable@vger.kernel.org>	[3.12+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I've been seeing swapoff hangs in recent testing: it's cycling around
trying unsuccessfully to find an mm for some remaining pages of swap.

I have been exercising swap and page migration more heavily recently,
and now notice a long-standing error in copy_one_pte(): it's trying to
add dst_mm to swapoff's mmlist when it finds a swap entry, but is doing
so even when it's a migration entry or an hwpoison entry.

Which wouldn't matter much, except it adds dst_mm next to src_mm,
assuming src_mm is already on the mmlist: which may not be so.  Then if
pages are later swapped out from dst_mm, swapoff won't be able to find
where to replace them.

There's already a !non_swap_entry() test for stats: move that up before
the swap_duplicate() and the addition to mmlist.
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: Kelley Nielsen <kelleynnn@gmail.com>
Cc: <stable@vger.kernel.org>	[2.6.18+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

a) don't bother with ->d_time for positives - we only check it for
   negatives anyway.

b) make sure to set it at unlink and rmdir time - at *that* point
   soon-to-be negative dentry matches then-current directory contents

c) don't go into renaming of old alias in vfat_lookup() unless it
   has the same parent (which it will, unless we are seeing corrupted
   image)

[hirofumi@mail.parknet.co.jp: make change minimum, don't call d_move() for dir]
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>	[3.17.x]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ipc_addid() makes a new ipc identifier visible to everyone.  New objects
start as locked, so that the caller can complete the initialization
after the call.  Within struct sem_array, at least sma->sem_base and
sma->sem_nsems are accessed without any locks, therefore this approach
doesn't work.

Thus: Move the ipc_addid() to the end of the initialization.
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Reported-by: NRik van Riel <riel@redhat.com>
Acked-by: NRik van Riel <riel@redhat.com>
Acked-by: NDavidlohr Bueso <dave@stgolabs.net>
Acked-by: NRafael Aquini <aquini@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If kzalloc() failed and then evdev_open_device() fails, evdev_open()
will pass a vmalloc'ed pointer to kfree.

This might fix https://bugzilla.kernel.org/show_bug.cgi?id=88401, where
there was a crash in kfree().
Reported-by: NChristian Casteyde <casteyde.christian@free.fr>
Belatedly-Acked-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Henrik Rydberg <rydberg@euromail.se>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NHariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These BUGs can be erroneously triggered by frags which refer to
tail pages within a compound page. The data in these pages may
overrun the hardware page while still being contained within the
compound page, but since compound_order() evaluates to 0 for tail
pages the assertion fails. The code already iterates through
subsequent pages correctly in this scenario, so the BUGs are
unnecessary and can be removed.

Fixes: f36c3747 ("xen/netfront: handle compound page fragments on transmit")
Cc: <stable@vger.kernel.org> # 3.7+
Signed-off-by: NSeth Forshee <seth.forshee@canonical.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In some android devices, there will be a "divide by zero" exception.
vmpr->scanned could be zero before spin_lock(&vmpr->sr_lock).

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=88051

[akpm@linux-foundation.org: neaten]
Reported-by: Nji_ang <ji_ang@163.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If a frontswap dup-store failed, it should invalidate the expired page
in the backend, or it could trigger some data corruption issue.
Such as:
 1. use zswap as the frontswap backend with writeback feature
 2. store a swap page(version_1) to entry A, success
 3. dup-store a newer page(version_2) to the same entry A, fail
 4. use __swap_writepage() write version_2 page to swapfile, success
 5. zswap do shrink, writeback version_1 page to swapfile
 6. version_2 page is overwrited by version_1, data corrupt.

This patch fixes this issue by invalidating expired data immediately
when meet a dup-store failure.
Signed-off-by: NWeijie Yang <weijie.yang@samsung.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Seth Jennings <sjennings@variantweb.net>
Cc: Dan Streetman <ddstreet@ieee.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Bob Liu <bob.liu@oracle.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Minor fixlet to perform the reserved pages counter aggregation for each
node, at show_mem()
Signed-off-by: NRafael Aquini <aquini@redhat.com>
Acked-by: NRik van Riel <riel@redhat.com>
Acked-by: NJohannes Weiner <jweiner@redhat.com>
Acked-by: NYasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A few more small fixes for 3.18.

* 'drm-fixes-3.18' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon: kernel panic in drm_calc_vbltimestamp_from_scanoutpos with 3.18.0-rc6
  drm/radeon: Ignore RADEON_GEM_GTT_WC on 32-bit x86
  drm/radeon: sync all BOs involved in a CS v2

I was unable too boot 3.18.0-rc6 because of the following kernel
panic in drm_calc_vbltimestamp_from_scanoutpos():

    [drm] Initialized drm 1.1.0 20060810
    [drm] radeon kernel modesetting enabled.
    [drm] initializing kernel modesetting (RV100 0x1002:0x515E 0x15D9:0x8080).
    [drm] register mmio base: 0xC8400000
    [drm] register mmio size: 65536
    radeon 0000:0b:01.0: VRAM: 128M 0x00000000D0000000 - 0x00000000D7FFFFFF (16M used)
    radeon 0000:0b:01.0: GTT: 512M 0x00000000B0000000 - 0x00000000CFFFFFFF
    [drm] Detected VRAM RAM=128M, BAR=128M
    [drm] RAM width 16bits DDR
    [TTM] Zone  kernel: Available graphics memory: 3829346 kiB
    [TTM] Zone   dma32: Available graphics memory: 2097152 kiB
    [TTM] Initializing pool allocator
    [TTM] Initializing DMA pool allocator
    [drm] radeon: 16M of VRAM memory ready
    [drm] radeon: 512M of GTT memory ready.
    [drm] GART: num cpu pages 131072, num gpu pages 131072
    [drm] PCI GART of 512M enabled (table at 0x0000000037880000).
    radeon 0000:0b:01.0: WB disabled
    radeon 0000:0b:01.0: fence driver on ring 0 use gpu addr 0x00000000b0000000 and cpu addr 0xffff8800bbbfa000
    [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
    [drm] Driver supports precise vblank timestamp query.
    [drm] radeon: irq initialized.
    [drm] Loading R100 Microcode
    radeon 0000:0b:01.0: Direct firmware load for radeon/R100_cp.bin failed with error -2
    radeon_cp: Failed to load firmware "radeon/R100_cp.bin"
    [drm:r100_cp_init] *ERROR* Failed to load firmware!
    radeon 0000:0b:01.0: failed initializing CP (-2).
    radeon 0000:0b:01.0: Disabling GPU acceleration
    [drm] radeon: cp finalized
    BUG: unable to handle kernel NULL pointer dereference at 000000000000025c
    IP: [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    PGD 0
    Oops: 0000 [#1] SMP
    Modules linked in:
    CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.18.0-rc6-4-default #2649
    Hardware name: Supermicro X7DB8/X7DB8, BIOS 6.00 07/26/2006
    task: ffff880234da2010 ti: ffff880234da4000 task.ti: ffff880234da4000
    RIP: 0010:[<ffffffff8150423b>]  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
    RSP: 0000:ffff880234da7918  EFLAGS: 00010086
    RAX: ffffffff81557890 RBX: 0000000000000000 RCX: ffff880234da7a48
    RDX: ffff880234da79f4 RSI: 0000000000000000 RDI: ffff880232e15000
    RBP: ffff880234da79b8 R08: 0000000000000000 R09: 0000000000000000
    R10: 000000000000000a R11: 0000000000000001 R12: ffff880232dda1c0
    R13: ffff880232e1518c R14: 0000000000000292 R15: ffff880232e15000
    FS:  0000000000000000(0000) GS:ffff88023fc40000(0000) knlGS:0000000000000000
    CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
    CR2: 000000000000025c CR3: 0000000002014000 CR4: 00000000000007e0
    Stack:
     ffff880234da79d8 0000000000000286 ffff880232dcbc00 0000000000002480
     ffff880234da7958 0000000000000296 ffff880234da7998 ffffffff8151b51d
     ffff880234da7a48 0000000032dcbeb0 ffff880232dcbc00 ffff880232dcbc58
    Call Trace:
     [<ffffffff8151b51d>] ? drm_vma_offset_remove+0x1d/0x110
     [<ffffffff8152dc98>] radeon_get_vblank_timestamp_kms+0x38/0x60
     [<ffffffff8152076a>] ? ttm_bo_release_list+0xba/0x180
     [<ffffffff81503751>] drm_get_last_vbltimestamp+0x41/0x70
     [<ffffffff81503933>] vblank_disable_and_save+0x73/0x1d0
     [<ffffffff81106b2f>] ? try_to_del_timer_sync+0x4f/0x70
     [<ffffffff81505245>] drm_vblank_cleanup+0x65/0xa0
     [<ffffffff815604fa>] radeon_irq_kms_fini+0x1a/0x70
     [<ffffffff8156c07e>] r100_init+0x26e/0x410
     [<ffffffff8152ae3e>] radeon_device_init+0x7ae/0xb50
     [<ffffffff8152d57f>] radeon_driver_load_kms+0x8f/0x210
     [<ffffffff81506965>] drm_dev_register+0xb5/0x110
     [<ffffffff8150998f>] drm_get_pci_dev+0x8f/0x200
     [<ffffffff815291cd>] radeon_pci_probe+0xad/0xe0
     [<ffffffff8141a365>] local_pci_probe+0x45/0xa0
     [<ffffffff8141b741>] pci_device_probe+0xd1/0x130
     [<ffffffff81633dad>] driver_probe_device+0x12d/0x3e0
     [<ffffffff8163413b>] __driver_attach+0x9b/0xa0
     [<ffffffff816340a0>] ? __device_attach+0x40/0x40
     [<ffffffff81631cd3>] bus_for_each_dev+0x63/0xa0
     [<ffffffff8163378e>] driver_attach+0x1e/0x20
     [<ffffffff81633390>] bus_add_driver+0x180/0x240
     [<ffffffff81634914>] driver_register+0x64/0xf0
     [<ffffffff81419cac>] __pci_register_driver+0x4c/0x50
     [<ffffffff81509bf5>] drm_pci_init+0xf5/0x120
     [<ffffffff821dc871>] ? ttm_init+0x6a/0x6a
     [<ffffffff821dc908>] radeon_init+0x97/0xb5
     [<ffffffff810002fc>] do_one_initcall+0xbc/0x1f0
     [<ffffffff810e3278>] ? __wake_up+0x48/0x60
     [<ffffffff8218e256>] kernel_init_freeable+0x18a/0x215
     [<ffffffff8218d983>] ? initcall_blacklist+0xc0/0xc0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
     [<ffffffff818a78fe>] kernel_init+0xe/0xf0
     [<ffffffff818c0c3c>] ret_from_fork+0x7c/0xb0
     [<ffffffff818a78f0>] ? rest_init+0x80/0x80
    Code: 45 ac 0f 88 a8 01 00 00 3b b7 d0 01 00 00 49 89 ff 0f 83 99 01 00 00 48 8b 47 20 48 8b 80 88 00 00 00 48 85 c0 0f 84 cd 01 00 00 <41> 8b b1 5c 02 00 00 41 8b 89 58 02 00 00 89 75 98 41 8b b1 60
    RIP  [<ffffffff8150423b>] drm_calc_vbltimestamp_from_scanoutpos+0x4b/0x320
     RSP <ffff880234da7918>
    CR2: 000000000000025c
    ---[ end trace ad2c0aadf48e2032 ]---
    Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009

It has helped me to add a NULL pointer check that was suggested at
http://lists.freedesktop.org/archives/dri-devel/2014-October/070663.html

I am not familiar with the code. But the change looks sane
and we need something fast at this stage of 3.18 development.
Suggested-by: NHelge Deller <deller@gmx.de>
Signed-off-by: NPetr Mladek <pmladek@suse.cz>
Tested-by: NPetr Mladek <pmladek@suse.cz>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=84627Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

Not just the userspace relocs, otherwise we won't wait
for a swapped out page tables to be swapped in again.

v2: rebased on Alex current drm-fixes-3.18
Signed-off-by: NChristian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

bio integrity handling is broken on a system with LVM layered atop a
DIF/DIX SCSI drive because device mapper clones the bio, modifies the
clone, and sends the clone to the lower layers for processing.
However, the clone bio has bi_vcnt == 0, which means that when the sd
driver calls bio_integrity_process to attach DIX data, the
for_each_segment_all() call (which uses bi_vcnt) returns immediately
and random garbage is sent to the disk on a disk write.  The disk of
course returns an error.

Therefore, teach bio_integrity_process() to use bio_for_each_segment()
to iterate the bio_vecs, since the per-bio iterator tracks which
bio_vecs are associated with that particular bio.  The integrity
handling code is effectively part of the "driver" (it's not the bio
owner), so it must use the correct iterator function.

v2: Fix a compiler warning about abandoned local variables.  This
patch supersedes "block: bio_integrity_process uses wrong bio_vec
iterator".  Patch applies against 3.18-rc6.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Merge tag 'keys-fixes-20141201' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into for-linus

Introduced in b440bde7, however it was added to
the wrong function in nouveau.

https://bugzilla.kernel.org/show_bug.cgi?id=86011
Cc: Bjorn Helgaas <bhelgaas@google.com>
CC: stable@vger.kernel.org  # v3.15+
Signed-off-by: NDave Airlie <airlied@redhat.com>

Just a couple of fixes for the fallout from the fence rework.

* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6:
  drm/nouveau/gf116: remove copy1 engine
  drm/nouveau: prevent stale fence->channel pointers, and protect with rcu
  drm/nouveau/fifo/g84-: ack non-stall interrupt before handling it

Indications are that no GF116's actually have a copy engine there, but
actually have the decompression engine. This engine can be made to do
copies, but that should be done separately.

Unclear why this didn't turn up on all GF116's, but perhaps the
non-mobile ones came with enough VRAM to not trigger ttm migrations in
test scenarios.

Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=85465
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=59168
Cc: stable@vger.kernel.org
Signed-off-by: NIlia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Tested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Closes a very unlikely race that can occur if another NonStallInterrupt
method passes between checking fences and acking the previous interrupt.

With this change, the interrupt will re-fire under such conditions.
Tested-by: NTobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Pull ext4 bugfix from Ted Ts'o:
 "Fix an ext4 metadata checksum regression introduced in v3.18-rc3"

* tag 'ext4_for_linus_urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  jbd2: fix regression where we fail to initialize checksum seed when loading

When we're enabling journal features, we cannot use the predicate
jbd2_journal_has_csum_v2or3() because we haven't yet set the sb
feature flag fields!  Moreover, we just finished loading the shash
driver, so the test is unnecessary; calculate the seed always.

Without this patch, we fail to initialize the checksum seed the first
time we turn on journal_checksum, which means that all journal blocks
written during that first mount are corrupt.  Transactions written
after the second mount will be fine, since the feature flag will be
set in the journal superblock.  xfstests generic/{034,321,322} are the
regression tests.

(This is important for 3.18.)
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.coM>
Reported-by: NEric Whitney <enwlinux@gmail.com>
Signed-off-by: NTheodore Ts'o <tytso@mit.edu>

Commit 0b0b0893 ("of/pci: Fix the conversion of IO ranges into IO
resources") changed how I/O resources are parsed from DT.  Rather than
containing the physical address of the I/O region, the addresses will now
be in I/O address space.

On Tegra the union of all ranges is used to expose a top-level memory-
mapped resource for the PCI host bridge.  This helps to make /proc/iomem
more readable.

Combining both of the above, the union would now include the I/O space
region.  This causes a regression on Tegra20, where the physical base
address of the PCIe controller (and therefore of the union) is located at
physical address 0x80000000.  Since I/O space starts at 0, the union will
now include all of system RAM which starts at 0x00000000.

This commit fixes this by keeping two copies of the I/O range: one that
represents the range in the CPU's physical address space, the other for the
range in the I/O address space.  This allows the translation setup within
the driver to reuse the physical addresses.  The code registering the I/O
region with the PCI core uses both ranges to establish the mapping.

Fixes: 0b0b0893 ("of/pci: Fix the conversion of IO ranges into IO resources")
Reported-by: NMarc Zyngier <marc.zyngier@arm.com>
Tested-by: NMarc Zyngier <marc.zyngier@arm.com>
Suggested-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>

Since the keyring facility can be viewed as a cache (at least in some
applications), the local expiration time on the key should probably be viewed
as a 'needs updating after this time' property rather than an absolute 'anyone
now wanting to use this object is out of luck' property.

Since request_key() is the main interface for the usage of keys, this should
update or replace an expired key rather than issuing EKEYEXPIRED if the local
expiration has been reached (ie. it should refresh the cache).

For absolute conditions where refreshing the cache probably doesn't help, the
key can be negatively instantiated using KEYCTL_REJECT_KEY with EKEYEXPIRED
given as the error to issue.  This will still cause request_key() to return
EKEYEXPIRED as that was explicitly set.

In the future, if the key type has an update op available, we might want to
upcall with the expired key and allow the upcall to update it.  We would pass
a different operation name (the first column in /etc/request-key.conf) to the
request-key program.

request_key() returning EKEYEXPIRED is causing an NFS problem which Chuck
Lever describes thusly:

	After about 10 minutes, my NFSv4 functional tests fail because the
	ownership of the test files goes to "-2". Looking at /proc/keys
	shows that the id_resolv keys that map to my test user ID have
	expired. The ownership problem persists until the expired keys are
	purged from the keyring, and fresh keys are obtained.

	I bisected the problem to 3.13 commit b2a4df20 ("KEYS: Expand
	the capacity of a keyring"). This commit inadvertantly changes the
	API contract of the internal function keyring_search_aux().

	The root cause appears to be that b2a4df20 made "no state check"
	the default behavior. "No state check" means the keyring search
	iterator function skips checking the key's expiry timeout, and
	returns expired keys.  request_key_and_link() depends on getting
	an -EAGAIN result code to know when to perform an upcall to refresh
	an expired key.

This patch can be tested directly by:

	keyctl request2 user debug:fred a @s
	keyctl timeout %user:debug:fred 3
	sleep 4
	keyctl request2 user debug:fred a @s

Without the patch, the last command gives error EKEYEXPIRED, but with the
command it gives a new key.
Reported-by: NCarl Hetherington <cth@carlh.net>
Reported-by: NChuck Lever <chuck.lever@oracle.com>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Tested-by: NChuck Lever <chuck.lever@oracle.com>

Simplify KEYRING_SEARCH_{NO,DO}_STATE_CHECK flags to be two variations of the
same flag.  They are effectively mutually exclusive and one or the other
should be provided, but not both.

Keyring cycle detection and key possession determination are the only things
that set NO_STATE_CHECK, except that neither flag really does anything there
because neither purpose makes use of the keyring_search_iterator() function,
but rather provides their own.

For cycle detection we definitely want to check inside of expired keyrings,
just so that we don't create a cycle we can't get rid of.  Revoked keyrings
are cleared at revocation time and can't then be reused, so shouldn't be a
problem either way.

For possession determination, we *might* want to validate each keyring before
searching it: do you possess a key that's hidden behind an expired or just
plain inaccessible keyring?  Currently, the answer is yes.  Note that you
cannot, however, possess a key behind a revoked keyring because they are
cleared on revocation.

keyring_search() sets DO_STATE_CHECK, which is correct.

request_key_and_link() currently doesn't specify whether to check the key
state or not - but it should set DO_STATE_CHECK.

key_get_instantiation_authkey() also currently doesn't specify whether to
check the key state or not - but it probably should also set DO_STATE_CHECK.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Tested-by: NChuck Lever <chuck.lever@oracle.com>

When a key description argument is imported into the kernel from userspace, as
happens in add_key(), request_key(), KEYCTL_JOIN_SESSION_KEYRING,
KEYCTL_SEARCH, the description is copied into a buffer up to PAGE_SIZE in size.
PAGE_SIZE, however, is a variable quantity, depending on the arch.  Fix this at
4096 instead (ie. 4095 plus a NUL termination) and define a constant
(KEY_MAX_DESC_SIZE) to this end.

When reading the description back with KEYCTL_DESCRIBE, a PAGE_SIZE internal
buffer is allocated into which the information and description will be
rendered.  This means that the description will get truncated if an extremely
long description it has to be crammed into the buffer with the stringified
information.  There is no particular need to copy the description into the
buffer, so just copy it directly to userspace in a separate operation.
Reported-by: NChristian Kastner <debian@kvr.at>
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Tested-by: NChristian Kastner <debian@kvr.at>