Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 24 1月, 2011 1 次提交
  3. 21 1月, 2011 7 次提交
  5. 20 1月, 2011 4 次提交
  7. 19 1月, 2011 14 次提交
  9. 18 1月, 2011 3 次提交
  11. 17 1月, 2011 1 次提交
    • N
      net: Make NETCONSOLE_DYNAMIC depend on CONFIGFS_FS · d9f9ab51
      由 Nicholas Bellinger 提交于 
      This patch fixes the following kconfig error after changing
CONFIGFS_FS -> select SYSFS:

fs/sysfs/Kconfig:1:error: recursive dependency detected!
fs/sysfs/Kconfig:1:	symbol SYSFS is selected by CONFIGFS_FS
fs/configfs/Kconfig:1:	symbol CONFIGFS_FS is selected by NETCONSOLE_DYNAMIC
drivers/net/Kconfig:3390:	symbol NETCONSOLE_DYNAMIC depends on SYSFS
Signed-off-by: NNicholas A. Bellinger <nab@linux-iscsi.org>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: James Bottomley <James.Bottomley@suse.de>
      d9f9ab51
  13. 16 1月, 2011 8 次提交
  15. 15 1月, 2011 2 次提交
    • D
      GRETH: resolve SMP issues and other problems · 0f73f2c5
      由 Daniel Hellstrom 提交于 
      Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
   unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
   temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
   descriptors were available after a SKB been scheduled by XMIT. Instead
   the TX queue is stopped first when not enough descriptors are available
   upon entering XMIT.

It was hard to split up this patch in smaller pieces since all are tied
together somehow.

Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.

By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.

TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.

Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      0f73f2c5
    • D
      GRETH: handle frame error interrupts · 1ca23434
      由 Daniel Hellstrom 提交于 
      Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: NDaniel Hellstrom <daniel@gaisler.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      1ca23434