Device role is always started along with ROC.
Couple them together by introducing new wl12xx_start_dev
and wl12xx_stop_dev functions.

By using these functions, we solve a bug that occured during
channel switch - we started the dev role on one channel, and
ROCed on a different one.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Injected packets are sent with no vif, causing the wl12xx
to NULL-dereference in multiple places.

Furthermore, injected packets are currently not sent at all,
as system_hlid doesn't belong to any specific role, so
wl1271_skb_dequeue() never return its packets.

Handle both these problems.
Reported-by: NLuciano Coelho <coelho@ti.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

There's no need to have the bus name included in the platform device
name that we create.  The core driver doesn't need to know about the
type of bus it uses.  Any differences between the buses that need to
be handled differently in the core, can be passed in the platform data
(as the pwr_in_suspend boolean does).

Use "wl12xx" for the device name in both bus drivers.  Rename the
platform driver name to "wl12xx_driver", just to differentiate from
the platform device names.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

mac80211 sets the carrier on an IBSS interface even when no network is
joined. Ignore garbage frames transmitted on a disconnected IBSS
interface without printing warnings.
Signed-off-by: NShahar Lev <shahar@wizery.com>
[merged with wlvif changes]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

To prevent a useless dependency between the spi module and the wl12xx
module, we need to replace the wl1271_error macros with dev_err.

At the same time, remove the SPI data hexdump, since this produces way
too much data and is not particularly useful.  There's no
print_hex_dump() equivalent for dynamic debug, so it's hard to control
when the dumps are printed out.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

To prevent a useless dependency between the sdio module and the wl12xx
module, we need to replace the wl1271_debug macros (and friends) for
dev_dbg and other equivalents.

At the same time, remove the SDIO data hexdump, since this produces
way too much data and is not particularly useful.  There's not
print_hex_dump() equivalent for dynamic debug, so it's hard to control
when the dumps are printed out.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Separate the debugging macros and other definitions to a new debug.h
file.  This is be needed because the sdio and spi modules don't need
to depend on the wl12xx module anymore, but still need to include
wl12xx.h.  Currently they do depend on it, because of the debugging
global that wl12xx exports.  A future patch will remove this
dependency.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

now that useless plat_dev is unnecessary,
we can remove it.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward ported and fixed sysfs file creation]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

after re-factoring a bunch of symbols are only
used inside main.c which allows us to mark
them as static.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Move all common parts from sdio.c and spi.c to main.c, since they now
can be handled as part of the platform driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[added a bunch of fixes and a new pdata element]
[moved some new code into main.c as well]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Nnow that we have a platform_device on both glue layers, add a
platform_driver to the core driver.

It's currently an empty platform_driver but more functionality will be
added on later patches.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[added platform_driver.driver initialization]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The platform device will be used to match the platform driver that
will be implemented by the core module.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[call platform_device_add() instead of platform_device_register()]
[store alloc'ed device platform directly in glue->core]
[fixed the length of memset(res...)]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The platform device will be used to match the platform driver that
will be implemented by the core module.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported, cleaned-up and rephrased commit message]
[call platform_device_add() instead of platform_device_register()]
[store alloc'ed device platform directly in glue->core]
[fixed the length of memset(res...)]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to fully abstract the bus, we need to save the device
structure *beside* wl1271, instead of inside it.

This will help re-structuring the driver so that we avoid the
duplicated code in the bus modules.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported and cleaned up and rephrased commit message]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

In order to fully abstract the bus, we need to save the device
structure *beside* wl1271, instead of inside it.

This will help re-structuring the driver so that we avoid the
duplicated code in the bus modules.
Signed-off-by: NFelipe Balbi <balbi@ti.com>
[forward-ported and cleaned up and rephrased commit message]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This module has been causing more trouble than being useful.  It only
tests the SDIO speed by connecting to the wl12xx chip and does some
throughput calculations.  It is an ugly quick hack and, if we really
want to have it as part of wl12xx we need to clean it up and implement
it properly.

A tarball of the code has been created and posted here, with some
instructions:

http://wireless.kernel.org/en/users/Drivers/wl12xx#SDIO_performance_test_moduleSigned-off-by: NLuciano Coelho <coelho@ti.com>

Currently, a single vif might starve all the other vifs.
Save the last vif we dequeued a packet from, and continue
with the following one using a round-robin policy.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add_interface might be called while the chip is
in elp. add elp_wakeup/sleep calls to handle it.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

allocate the rate policies dynamically, instead of using hardcoded
indexes. this is needed for proper multi-role configuration.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The recovery work should call stop() after it removed
all the existing interfaces.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl->vif is appropriate only when a single vif is being used.
Instead, pass wlvif as parameter or iterate through all
the vifs (e.g. when a global configuration was changed)

Leave wl->vif only to determine whether a vif was already
added (this check will be removed as well after both the
driver and fw will support multiple vifs)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

When mac80211 changes a global (hw) config, iterate
through all the relevant vifs and update them.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move power_level into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add channel into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

add band field into the per-interface data.

mac80211 configures some values (e.g. band, channel)
globally, while we configure them per-interface.

In order to make it easier to keep track of the
configured value for each value while keeping sync
with mac80211, save these values both globally
and per-vif.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Make the initialization flag per-vif, and add some checks for it.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

move WL1271_FLAG_PSM and WL1271_FLAG_PSM_REQUESTED into
per-vif flags.
These flags should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

This flag should be set per-vif, rather than globally.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Currently, the rx streaming doesn't support multi-vif
(the actual wlvif is taken from wl->vif, and the management
is global).

Make the rx streaming timers/works per-vif, and pass the
the actual vif as param.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The last security seq num has to be saved across reconfigs.
Add a new "persistent" struct into wlvif, which won't get
deleted on wl12xx_init_vif_data()
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Some events don't indicate the role they are intended for.
In these cases, iterate through all the relevant vifs,
and pass the event to each one of them.

This is only a workaround. future fw releases should indicate
the relevant role_id for such events.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

If there is an active AP role, stay always on.
Otherwise, allow chip to enter elp.

(Note that this is a global configuration, so if the
device is already configured according to our policy,
we don't have to configure it again)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Pass the wlvif associated with each skb as param.

Note that dummy packet doesn't belong to any
particular vif, so we pass NULL in this case.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

keep a list of all the vifs associated with our hw.
it will be later used in order to iterate through vifs.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>