An LTTPR can be trained with training pattern 4 even if the DPCD
revision is < 1.4, but drm_dp_training_pattern_mask() would change
pattern 4 to pattern 3 on those DPCD revisions.

Since intel_dp_training_pattern() makes already sure that the proper
training pattern is used, all that needs to be masked out is the
scrambling disable flag, which is or'd to the mask later based on the
training pattern.

v2:
- Use a helper instead of open-coding the masking. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201007170917.1764556-2-imre.deak@intel.com

Extend the eDP panel power cycle delay wait on reboot handling
to cover all platforms. No reason to think that VLV/CHV are
in any way special since the documentation states that the
hardware power cycle delay goes back to its default value on
reset, and that may not be enough for all panels.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001151640.14590-4-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>

Recent update in documentation defeatured eDP HBR3 for EHL and JSL.

v2:
- Remove dead code in ehl_get_combo_buf_trans()

v3:
- Rebase

BSpec: 32247
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vidya Srinivas <vidya.srinivas@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005175447.93430-1-jose.souza@intel.com

Atm, if a full modeset is performed during the initial modeset the link
training will happen with uninitialized max DP rate and lane count. Make
sure the corresponding encoder state is initialized by adding an encoder
hook called during driver init and system resume.

A better alternative would be to store all states in the CRTC state and
make this state available for the link re-training code. Also instead of
the DPCD read in the hook there should be really a proper sink HW
readout in place. Both of these require a bigger rework, so for now opting
for this minimal fix to make at least full initial modesets work.

The patch is based on
https://patchwork.freedesktop.org/patch/101473/?series=10354&rev=3

v2: (Ville)
- s/sanitize_state/sync_state/
- No point in calling the hook when CRTC is disabled, remove the call.
- No point in calling the hook for MST, remove it.

v3: Check only DPCD_REV to avoid clobbering intel_dp->dpcd. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005230154.1477653-1-imre.deak@intel.com

Move the checks to decide whether a fastset is possible during the
initial commit to an encoder hook. This check is really encoder specific
and the next patch will also require this adding a DP encoder specific
check.

v2: Fix negated condition in gen11_dsi_initial_fastset_check().
v3: Make sure to call the hook for all encoders on the crtc. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201005215311.1475666-1-imre.deak@intel.com

On HP 800 G4 DM, if HDMI cable isn't plugged before boot, the HDMI port
becomes useless and never responds to cable hotplugging:
[    3.031904] [drm:lspcon_init [i915]] *ERROR* Failed to probe lspcon
[    3.031945] [drm:intel_ddi_init [i915]] *ERROR* LSPCON init failed on port D

Seems like the lspcon chip on the system only gets powered after the
cable is plugged.

Consilidate lspcon_init() into lspcon_resume() to dynamically init
lspcon chip, and make HDMI port work.

v6:
 - Rebase on latest for-linux-next.
v5:
 - Consolidate lspcon_resume() with lspcon_init().
 - Move more logic into lspcon code.
v4:
 - Trust VBT in intel_infoframe_init().
 - Init lspcon in intel_dp_detect().
v3:
 - Make sure it's handled under long HPD case.
v2:
 - Move lspcon_init() inside of intel_dp_hpd_pulse().

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/203Signed-off-by: NKai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200610075542.12882-1-kai.heng.feng@canonical.com

Now that we've plumbed the crtc state all the way down we can
eliminate the DP_TP_{CTL,STATUS} register offsets from intel_dp,
and instead we derive them directly from the crtc state.

And thus we can get rid of the nasty hack in intel_ddi_get_config()
which mutates intel_dp during the readout.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-12-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Get rid of mode crtc->config usage, and some ad-hoc intel_dp state
usage by plumbing the crtc state all the way down to the link training
code.

Unfortunately we do have to keep some cached state in intel_dp so
that we can do the "does the link need retraining?" checks from
the short hpd handler.

v2: Add intel_crtc_state forward declaration
v3: Don't kill the PHY test code totally since it's
    now in the hotplug work where we can get at the states
v4: Don't resurrect the debug scrambling disable bit (Imre)
    Use intel_dp_mst_is_master_trans() (Imre)
Reviewed-by: NImre Deak <imre.deak@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201001111053.24451-1-ville.syrjala@linux.intel.com

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-10-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-9-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-8-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-7-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Make the mess inside the buf trans funcs a bit more manageable by
splitting along the lines of output type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929233449.32323-6-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The HDMI vs. not-HDMI check got inverted whem the bogus encoder->type
checks were eliminated. So now we're using 0 as the link rate on DP
and potentially non-zero on HDMI, which is exactly the opposite of
what we want. The original bogus check actually worked more correctly
by accident since if would always evaluate to true. Due to this we
now always use the RBR/HBR1 vswing table and never ever the HBR2+
vswing table. That is probably not a good way to get a high quality
signal at HBR2+ rates. Fix the check so we pick the right table.

Cc: stable@vger.kernel.org
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Fixes: 94641eb6 ("drm/i915/display: Fix the encoder type check")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200930223642.28565-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NVandita Kulkarni <vandita.kulkarni@intel.com>

DP 1.3 adds some extra control knobs for DP->HDMI protocol conversion.
Let's use that to configure the "HDMI mode" (ie. infoframes vs. not)
based on the capabilities of the sink.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-13-ville.syrjala@linux.intel.comReviewed-by: NLyude Paul <lyude@redhat.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Non-HDMI sinks shouldn't be sent infoframes. Check for that when
using LSPCON.

FIXME: How do we turn off infoframes once enabled? Do we even
       have to?
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200904115354.25336-3-ville.syrjala@linux.intel.comReviewed-by: NLyude Paul <lyude@redhat.com>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Make a clean split between hpd pins for DDI vs. TC. This matches
how the actual hardware is split.

And with this we move the DDI/PHY->HPD pin mapping into the encoder
init instead of having to remap yet again in the interrupt code.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-11-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

Currently DP/HDMI/DDI encoders init their hpd_pin from the
connector init. Let's move it to the encoder init so that
we don't need to add platform specific junk to the connector
init (which is shared by all g4x+ platforms).
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200630215601.28557-10-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

In order to act upon content_protection property changes, we'll need to
implement the .update_pipe() hook. We can re-use intel_ddi_update_pipe
for this
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-10-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-11-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-11-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-11-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-11-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-11-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-12-sean@poorly.run #v7

Changes in v2:
-None
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-None
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-12-sean@poorly.run

This patch is required for HDCP over MST. If a port is being used for
multiple HDCP streams, we don't want to fully disable HDCP on a port if
one of them is disabled. Instead, we just disable the HDCP signalling on
that particular pipe and exit early. The last pipe to disable HDCP will
also bring down HDCP on the port.

In order to achieve this, we need to keep a refcount in intel_digital_port
and protect it using a new hdcp_mutex.

Cc: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191203173638.94919-8-sean@poorly.run #v1
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-9-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-9-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-9-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-9-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-9-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-10-sean@poorly.run #v7

Changes in v2:
-Move the toggle_signalling call into _intel_hdcp_disable so it's called from check_work
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-Split minor intel_hdcp_disable refactor into separate patch (Ramalingam)
Changes in v8:
-None
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-10-sean@poorly.run

Instead of using intel_dig_port's encoder pipe to determine which
transcoder to toggle signalling on, use the cpu_transcoder field already
stored in intel_hdmi.

This is particularly important for MST.
Suggested-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-6-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-6-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-6-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-6-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-6-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-6-sean@poorly.run #v7

Changes in v2:
-Added to the set
Changes in v3:
-s/hdcp/hdmi/ in commit msg (Ram)
Changes in v4:
-Rebased on intel_de_(read|write) change
Changes in v5:
-Update hdcp->cpu_transcoder in intel_hdcp_enable so it works with pipe != 0
Changes in v6:
-None
Changes in v7:
-None
Changes in v8:
-None
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-6-sean@poorly.run

HDCP signalling should not be left on, WARN if it is

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NRamalingam C <ramalingam.c@intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191212190230.188505-4-sean@poorly.run #v2
Link: https://patchwork.freedesktop.org/patch/msgid/20200117193103.156821-4-sean@poorly.run #v3
Link: https://patchwork.freedesktop.org/patch/msgid/20200218220242.107265-4-sean@poorly.run #v4
Link: https://patchwork.freedesktop.org/patch/msgid/20200305201236.152307-4-sean@poorly.run #v5
Link: https://patchwork.freedesktop.org/patch/msgid/20200429195502.39919-4-sean@poorly.run #v6
Link: https://patchwork.freedesktop.org/patch/msgid/20200623155907.22961-4-sean@poorly.run #v7

Changes in v2:
-Added to the set in lieu of just clearing the bit
Changes in v3:
-None
Changes in v4:
-None
Changes in v5:
-Change WARN_ON to drm_WARN_ON
Changes in v6:
-None
Changes in v7:
-Rebased, variable name changed from 'ctl' to 'val'
Changes in v8:
-None
Signed-off-by: NRamalingam C <ramalingam.c@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200818153910.27894-4-sean@poorly.run

Update with latest tuning in the table.

v3: Fix values of to last columns.

BSpec: 21257
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-3-jose.souza@intel.com

Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.

v2: Only use icl_combo_phy_ddi_translations_edp_hbr3 if low_vswing is
set as EHL combo phy supports HBR3 (Matt R)
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-2-jose.souza@intel.com

Reusing icl_get_combo_buf_trans() for eDP was causing the wrong table
being used when the eDP port don't support low power voltage swing table.
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Cc: Lee Shawn C <shawn.c.lee@intel.com>
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200826201549.83658-1-jose.souza@intel.com

Changes in the configuration could cause PSR to be compatible and
enabled so driver must also be able to disable DRRS when doing
fastsets.

v2: Fixed name of DRRS compute function (Anshuman)

Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/173
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/209
Cc: Srinivas K <srinivasx.k@intel.com>
Cc: Hariom Pandey <hariom.pandey@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825171331.17971-2-jose.souza@intel.com

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

This new HBR2 table for TGL-U and TGL-Y is required to pass
DisplayPort compliance.

BSpec: 49291
Cc: Khaled Almahallawy <khaled.almahallawy@intel.com>
Reviewed-by: Khaled Almahallawy<khaled.almahallawy@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200807192629.64134-2-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

If HTI (also sometimes called HDPORT) is enabled at startup, it may be
using some of the PHYs and DPLLs making them unavailable for general
usage.  Let's read out the HDPORT_STATE register and avoid making use of
resources that HTI is already using.

v2:
 - Fix minor checkpatch warnings

v3:
 - Just readout HDPORT_STATE register once during init and then parse it
   later as needed.
 - Add a 'has_hti' device info flag to track whether we should readout
   HDPORT_STATE or not.  We can skip the platform/flag tests later since
   the hti_state in dev_priv will remain 0 for platforms it does not
   apply to.
 - Move PLL masking into icl_get_combo_phy_dpll() since at the moment
   RKL is the only platform that has HTI.  (Jose)

Bspec: 49189
Bspec: 53707
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-5-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

RKL uses a slightly different bit layout for the DPCLKA_CFGCR0 register.

v2:
 - Fix inverted mask application when updating ICL_DPCLKA_CFGCR0
 - Checkpatch style fixes

Bspec: 50287
Cc: Aditya Swarup <aditya.swarup@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200716220551.2730644-2-matthew.d.roper@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Hours Of Battery Life is a new GEN12+ power-saving feature that allows
supported motherboards to use a special voltage swing table for eDP
panels that uses less power.

So here if supported by HW, OEM will set it in VBT and i915 will try
to train link with HOBL vswing table if link training fails it fall
back to the original table.

intel_ddi_dp_preemph_max() was optimized to only check the HOBL flag
instead of do something like is done in intel_ddi_dp_voltage_max()
because it is only called after the first entry of the voltage swing
table was loaded so the HOBL flag is valid at that point.

v3:
- removed a few parameters of icl_ddi_combo_vswing_program() that
can be taken from encoder

v4:
- using the HOBL vswing table until training fails completely (Ville)

v5:
- not reducing lane or link rate when link training fails with HOBL
active
- duplicated the HOBL voltage swing entry to match DP spec requirement

v6:
- removed the optional VS 3 & pre-emp 0 from HOBL table
- changed from u8:1 to bool to store hobl_failed/active

BSpec: 49291
BSpec: 49399
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Animesh Manna <animesh.manna@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200715175637.33763-1-jose.souza@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

The value we program to DDI_BUF_CTL changes at the following places:
- At enabling/disabling the output to configure the port width etc, and
  to enable/disable the DDI BUF function.
- At the beginning/end of link re-training to disable/re-enable the DDI
  BUF function.
- On HSW/BDW/SKL to change the voltage swing/pre-emph levels.

Except of the above the value we program to the DDI_BUF_CTL register
(intel_dp->DP) doesn't change, so no need to reprogram the register when
changing the link training patterns (which is programmed via the
DP_TP_CTL register on DDI platforms).

v2:
- Fix the commit message wrt. voltage/pre-emph level values in
  intel_dp->DP. (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-2-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

According to BSpec this flag should not be changed while the DDI
function is enabled. On BDW+ the DP_TP_CTL register spec also states it
explicitly that the HW takes care of enabling/disabling the scrambling
for training patterns (and it must stay enabled for normal pixel
output). Assume that this HW automatic handling of scrambling is also
true for HSW.

BSpec: 8013, 7557, 50484
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200714153141.10280-1-imre.deak@intel.comSigned-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

This information can be get directly from intel_encoder so no need
of those parameters.
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708205512.21625-2-jose.souza@intel.com

intel_encoder will be needed inside of vswing functions in a future
patch, so here doing this change in all vswing functions since HSW.
Signed-off-by: NJosé Roberto de Souza <jose.souza@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708205512.21625-1-jose.souza@intel.com

Based on the platform, Bspec expects us to wait or poll with
timeout for DDI BUF IDLE bit to be set to 0 (non idle) or get active
after enabling DDI_BUF_CTL.

v2:
* Based on platform, fixed delay or poll (Ville)
* Use a helper to do this (Imre, Ville)
v3:
* Add a new function _active for DDI BUF CTL to be non idle (Ville)
v4:
* Use the timeout for GLK (Ville)
v5:
* Add bspec quote, change timeout to 500us (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-2-manasi.d.navare@intel.com

Modify the helper to add a fixed delay or poll with timeout
based on platform specification to check for either Idle bit
set (DDI_BUF_CTL is idle for disable case)

v2:
* Use 2 separate functions or idle and active (Ville)
v3:
* Change the timeout to 16usecs (Ville)
v4:
* Change the timeout 8, follow spec (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Signed-off-by: NManasi Navare <manasi.d.navare@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701221052.8946-1-manasi.d.navare@intel.com

We have a mix of dport, intel_dport, intel_dig_port and dig_port to
reference a intel_digital_port struct. Numbers are around

5	intel_dport
36	dport
479	intel_dig_port
352	dig_port

Since we already removed the intel_ prefix from most of our other
structs, do the same here and prefer dig_port.

v2: rename everything in i915, not just a few display sources and
reword commit message (from Matt Roper)
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200701045054.23357-1-lucas.demarchi@intel.com

We don't need intel_dig_port and dig_port to refer to the same thing.
Prefer the latter.

v2: fix coding style
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200626234834.26864-2-lucas.demarchi@intel.com

The spec requires enabling the MST Virtual Channel payload allocation
- in a separate step - after the transcoder is enabled, follow this.

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200623082411.3889-1-imre.deak@intel.com