We may have the L-SIG length depending on the phy_data info type;
add it to radiotap when we do.

Move getting the phy_data out one layer up and the info type into
it so we can use this data more generically. We need to call the
iwl_mvm_rx_he() function for other reasons as well, so can't just
combine all of that into something like iwl_mvm_parse_phy_data().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware changed the PHY data API, so follow suit.
Some data is now available even for HT/VHT frames, so
the info type in the metadata was changed. This change
isn't backwards compatible, but
 1) the firmware with the old API was never released;
 2) the only overlap in the info type field is from the
    old type of TB to the new of HT, so this basically
    just means that with older FW and newer driver the
    data will be considered missing.

While at it, remove the extra code to set the LTF syms
corresponding to the streams and use the data from the
device instead - we don't really need this in any case
other than when we have it from the device.

As the new API gives use the spatial reuse 1-4 fields
for trigger-based PPDUs, also expose that to radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When removing the driver, the following flow can happen:
1. host command is in progress, for example at index 68.
2. RX interrupt is received with the response.
3. Before it is processed, the remove flow kicks in, and
   calls iwl_pcie_txq_unmap. The function cleans all DMA,
   and promotes the read pointer to 69.
4. RX thread proceeds with the processing, and is calling
   iwl_pcie_cmdq_reclaim, which will print this error:
   iwl_pcie_cmdq_reclaim: Read index for DMA queue txq id (0),
   index 4 is out of range [0-256] 69 69.

Detect this situation, and avoid the print. Change it to
warning while at it, to make such issues more noticeable
in the future.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.

Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Now that nvm_calib_ver is not checked in opmodes other than dvm, we
can remove it from all irrelevant configurations.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This function is only half-used by mvm (i.e. only the nvm_version part
matters, since the calibration version is irrelevant), so it's
pointless to export it from iwlwifi.  If mvm uses this function, it
has the additional complexity of setting the calib version to a bogus
value on all cfg structs.

To avoid this, move the function to dvm and make a simple comparison
of the nvm_version in mvm instead.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

These macros are useless because each one of them is used only once
and the element they are assigned to is already pretty clear about
what they mean, "nvm_hw_section_num".
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Using OTP_LOW_IMAGE_SIZE_FAMILY_8000/9000/22000 only obfuscates the
actual values, since these 3 are the same.  Redefine the values per
size so it's easier to understand and compare the different
configurations.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Call the previously introduced apply points entry
point when reaching an apply point.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add support for ini triggers.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When ini TLVs are loaded, dump data according to the
stored configuration.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The ht_params, nvm_ver, nvm_calib_ver and max_ht_ampdu_exponent
elements in 9000 devices are always the same.  Move them to the common
macro.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c: In function 'translate_rx_signal_stuff':
drivers/net/wireless/realtek/rtlwifi/rtl8821ae/trx.c:309:6: warning:
 variable 'type' set but not used [-Wunused-but-set-variable]

It never used since commit 21e4b072 ("rtlwifi: rtl8821ae: Move driver from
staging to regular tree")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

entry is released via usb_put_urb just after calling usb_submit_urb.
However, entry is used if the submission fails, resulting in a use after
free bug. The patch fixes this.
Signed-off-by: NPan Bian <bianpan2016@163.com>
ACKed-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/net/wireless/broadcom/b43/phy_n.c: In function 'b43_nphy_op_recalc_txpower':
drivers/net/wireless/broadcom/b43/phy_n.c:5898:7: warning:
 variable 'tx_pwr_state' set but not used [-Wunused-but-set-variable]

drivers/net/wireless/broadcom/b43/phy_n.c:6047:20: warning:
 variable 'tmp2' set but not used [-Wunused-but-set-variable]

'tx_pwr_state' never used since introduction in commit
8615eb28 ("b43: N-PHY: support setting custom TX power")

'tmp2' not used any more since commit c002831a ("b43: N-PHY: use helper
for checking IPA")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When CONFIG_NO_AUTO_INLINE is set, we get a false-postive warning
for the brcmf_fw_request_nvram_done() function, after gcc figures
out that brcmf_fw_nvram_from_efi() might not set the 'data_len'
variable, but fails to notice that it always returns NULL:

drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c: In function 'brcmf_fw_request_nvram_done':
drivers/net/wireless/broadcom/brcm80211/brcmfmac/firmware.c:560:11: error: 'data_len' may be used uninitialized in this function [-Werror=maybe-uninitialized]

Mark it 'inline' to force gcc to understand this.

Fixes: ce2e6db5 ("brcmfmac: Add support for getting nvram contents from EFI variables")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

AOS is a part of the SDIOD core that becomes active when the rest of
SDIOD is sleeping to keep SDIO bus alive responding to reduced set of
commands.

Transaction between AOS and SDIOD is not protected, and if cmd 52 is
received in AOS and in the middle of response state changed from AOS to
SDIOD, response is corrupted and it causes to SDIO Host controller to
hang.

Command decode for below chips are disabled in this commit:
 - 4339
 - 4345
 - 4354
 - 4373
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NWright Feng <wright.feng@cypress.com>
Signed-off-by: NDouble Lo <double.lo@cypress.com>
Signed-off-by: NMadhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use chipcommon sr_control0 register to check 4373 sr support.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The number of words that the read FIFO has to contain except
the end of frame before sends data back to the host.
Max watermark = (512B - 2* (BurstLength))/4 =
(512 - 128)/4 = 384/4 = 0x60
so if burst length (i.e. BurstLength = 64) is increased,
watermark has to be reduced. This is the optimal setting for this chip.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NNaveen Gupta <naveen.gupta@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

GCI core is needed for ULP operation. Allow GCI core enumuration with
below changes:
 - Allow GCI to be added to core list even when it doesn't have a wrapper.
 - Allow 8K address space size.
 - Don't overwrite the address value when an additional size descriptor
   is in place.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

CYW43012 is a 1x1 802.11a/b/g/n Dual-Band HT20, 256-QAM/Turbo QAM. It
is an Ultra Low Power WLAN+BT combo chip.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NPraveen Babu C <praveen.chandran@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Along with F2 watermark (existing) configuration, F1 MesBusyCtrl
should be enabled & sdio device RX FIFO watermark should be
configured to avoid overflow errors.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NMadhan Mohan R <madhanmohan.r@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We got SDIO_CRC_ERROR with 4373 on SDR104 when doing bi-directional
throughput test. Enable watermark to 256 to guarantee the operation
stability.
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NWright Feng <wright.feng@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the raw 4354 PCIe device ID for unprogrammed Cypress boards.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Signed-off-by: NWinnie Chang <winnie.chang@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware inform the driver about tx status by normal tx status signal
or compressed tx status signal. This patch adds support to handle the
compressed tx status signal.
Signed-off-by: NChung-Hsien Hsu <stanley.hsu@cypress.com>
Signed-off-by: NChi-Hsien Lin <chi-hsien.lin@cypress.com>
Signed-off-by: NWright Feng <wright.feng@cypress.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The frameburst feature can enable per-packet framebursting in firmware
side and get higher TX throughput in High Throughput(HT) mode. To enhance
TX throughput, we enable frameburst mode in default firmware setting.
Signed-off-by: NWright Feng <wright.feng@cypress.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The credit numbers are static and tunable per chip in firmware side.
However the credit number may be changed that is based on packet pool
length and will send BRCMF_E_FIFO_CREDIT_MAP event to notify host driver
updates the credit numbers during interface up.
The purpose of this patch is making host driver has ability of updating
the credit numbers when receiving the BRCMF_E_FIFO_CREDIT_MAP event.
Signed-off-by: NWright Feng <wright.feng@cypress.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Comparing the existing TX_BITRATE parsing code (in
mwifiex_parse_htinfo()) with the RX bitrate histograms in debugfs.c, it
appears that the rxpd_rate and rxpd_htinfo fields have the same format.
At least, they give reasonable results when I parse them this way.

So this patch adds support for RX_BITRATE to our station info dump.

Along the way, I add legacy bitrate parsing into the same function,
using the debugfs code (mwifiex_histogram_read() and
mwifiex_adjust_data_rate()) as reference.

Additionally, to satisfy the requirements of
NL80211_STA_INFO_RX_BITRATE, I skip logging the bitrate of multicast
packets. This shouldn't add a lot of overhead to the RX path, as there
are already several similar 802.3 header checks in this same codepath.
We can also bias the branch behavior to favor unicast, as that's the
common performance-sensitive case.

I'd consider this support somewhat experimental, as I have zero
documentation from Marvell. But the existing driver code gives me good
reason to think this is correct.

I've tested this on a few different 802.11{a,b,g,n,ac} networks, and the
reported bitrates look good to me.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This function converts some firmware-specific parameters into cfg80211
'rate_info' structures. It currently assumes it's dealing only with TX
bitrate, but the RX bitrate looks to be the same, so refactor this
function to be reusable.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently, snippets of this file look like:

rx rates (in Mbps): 0=1M   1=2M2=5.5M  3=11M   4=6M   5=9M  6=12M
7=18M  8=24M  9=36M  10=48M  11=54M12-27=MCS0-15(BW20) 28-43=MCS0-15(BW40)
44-53=MCS0-9(VHT:BW20)54-63=MCS0-9(VHT:BW40)64-73=MCS0-9(VHT:BW80)
...
noise_flr[--96dBm] = 22
noise_flr[--95dBm] = 149
noise_flr[--94dBm] = 9
noise_flr[--93dBm] = 2

We're missing some spaces, and we're adding a minus sign ('-') on values
that are already negative signed integers.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are two defects: (1) passing a NULL bss to
mwifiex_save_hidden_ssid_channels will result in NULL dereference,
(2) using bss after dropping the reference to it via cfg80211_put_bss.
To fix them, the patch moves the buggy code to the branch that bss is
not NULL and puts it before cfg80211_put_bss.
Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

first batch of mt76 patches for 4.21

* use the same firmware for mt76x2e and mt76x2u
* mt76x2 fixes
* mt76x0 fixes
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2

kvalo: fixed a conflict in drivers/net/wireless/mediatek/mt76/mt76x2/pci_main.c
and a build problem in drivers/net/wireless/mediatek/mt76/mt76x02_util.c

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Acked-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use DEFINE_SHOW_ATTRIBUTE macro to simplify the code.
Signed-off-by: NYangtao Li <tiny.windzz@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tariq Toukan says:

====================
mlx4_core cleanups

This patchset by Erez contains cleanups to the mlx4_core driver.

Patch 1 replaces -EINVAL with -EOPNOTSUPP for unsupported operations.
Patch 2 fixes some coding style issues.

Series generated against net-next commit:
97e6c858 net: usb: aqc111: Initialize wol_cfg with memset in aqc111_suspend
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 3 checkpatch errors within mlx4/main.c:
- Unnecessary mlx4_debug_level global variable initialization to 0.
- Prohibited space before comma.
- Whitespaces instead of tab.
Signed-off-by: NErez Alfasi <ereza@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Functions __set_port_type and mlx4_check_port_params returned
-EINVAL while the proper return code is -EOPNOTSUPP as a
result of an unsupported operation. All drivers should generate
this and all users should check for it when detecting an
unsupported functionality.
Signed-off-by: NErez Alfasi <ereza@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Logic of phy_device_create() requests PHY modules according to PHY ID
but for C45 PHYs we use different field for the IDs.

Let's also request the modules for these IDs.

Changes from v1:
- Only request C22 modules if C45 are not present (Andrew)
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Joao Pinto <joao.pinto@synopsys.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>