Intel hw only has one MUX for encoders, so outputs are either not
cloneable or all in the same group of cloneable outputs. This neatly
simplifies the code and allows us to ditch some ugly if cascades in
the dp and hdmi init code (well, we need these if cascades for other
stuff still, but that can be taken care of in follow-up patches).

Note that this changes two things:
- dvo can now be cloned with sdvo, but dvo is gen2 whereas sdvo is
  gen3+, so no problem. Note that the old code had a bug and didn't
  allow cloning crt with dvo (but only the other way round).
- sdvo-lvds can now be cloned with sdvo-non-tv. Spec says this won't
  work, but the only reason I've found is that you can't use the
  panel-fitter (used for lvds upscaling) with anything else. But we
  don't use the panel fitter for sdvo-lvds. Imo this part of Bspec is
  a) rather confusing b) mostly as a guideline to implementors (i.e.
  explicitly stating what is already implicit from the spec, without
  always going into the details of why). So I think we can ignore this
  - worst case we'll get a bug report from a user with with sdvo-lvds
  and sdvo-tmds and have to add that special case back in.

Because sdvo lvds is a bit special explain in comments why sdvo LVDS
outputs can be cloned, but native LVDS and eDP can't be cloned - we
use the panel fitter for the later, but not for sdvo.

Note that this also uncoditionally initializes the panel_vdd work used
by eDP. Trying to be clever doesn't buy us anything (but strange bugs)
and this way we can kill the is_edp check.

v2: Incorporate review from Paulo
- Add in a missing space.
- Pimp comment message to address his concerns.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Splitting them up between pch and gmch variants just makes it harder
to find things. Especially since the hotplug bits are actually valid
on earlier chips, too.

v2: Fixed the comment as pointed out by Paulo Zanoni.
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When bug hunting, I found the interface to do_switch() overly
complicated and I believe festered the earlier bug. This aims to make
the code a little clearer.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the DP structure to shared location so that it can be used from
within the ddi module.

Changes from Paulo:
- Move less code to intel_drv.h
- Remove #include statement
- Replace a tab with a space in train_set
Signed-off-by: NShobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We now refuse to load on gen6+ if kms is not enabled:

commit 26394d92
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Mon Mar 26 21:33:18 2012 +0200

    drm/i915: refuse to load on gen6+ without kms

Which results in the drm core calling our lastclose function to clean
up the mess, but that one is neatly broken for such failure cases
since kms has been introduced in

commit 79e53945
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Fri Nov 7 14:24:08 2008 -0800

    DRM: i915: add mode setting support
Reported-and-tested-by: NPaulo Zanoni <przanoni@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fixes failures in transform feedback on gen7 because our SOL_RESET
flag was setting the transform feedback offsets in the old context
(occasionally happened to be ours) instead of the new context.
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Laurent Pinchart missed this when sending in is giant constify patch:

commit e811f5ae
Author: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Date:   Tue Jul 17 17:56:50 2012 +0200

    drm: Make the .mode_fixup() operations mode argument a const pointer

Acked-by; Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

LVDS is the first output where dpms on/off and prepare/commit don't
perfectly match. Now the idea behind this special case seems to be
that for simple resolution changes on the LVDS we don't need to stop
the pipe, because (at least on newer chips) we can adjust the panel
fitter on the fly.

There are a few problems with the current code though:
- We still stop and restart the pipe unconditionally, because the crtc
  helper code isn't flexible enough.
- We show some ugly flickering, especially when changing crtcs (this
  the crtc helper would actually take into account, but we don't
  implement the encoder->get_crtc callback required to make this work
  properly).

So it doesn't even work as advertised. I agree that it would be nice
to do resolution changes on LVDS (and also eDP) whithout blacking the
screen where the panel fitter allows to do that. But imo we should
implement this as a special case a few layers up in the mode set code,
akin to how we already detect simple framebuffer changes (and only
update the required registers with ->mode_set_base).

Until this is all in place, make our lives easier and just rip it out.

Also note that this seems to fix actual bugs with enabling the lvds
output, see:

http://lists.freedesktop.org/archives/intel-gfx/2012-July/018614.html

Cc: Takashi Iwai <tiwai@suse.de>
Cc: Giacomo Comes <comes@naic.edu>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Tested-by: NTakashi Iwai <tiwai@suse.de>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to check that "ctx" is a valid pointer before dereferencing it.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Otherwise we end up trying to unpin a freed object and BUG.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This prevents a WARN introduced with

  commit de2b9985
  Author: Daniel Vetter <daniel.vetter@ffwll.ch>
  Date:   Wed Jul 4 22:52:50 2012 +0200

      drm/i915: don't return a spurious -EIO from intel_ring_begin
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The issue is that we stale data in the CPU caches, when we come to
swap-out the object, the CPU may short-circuit the reads from those
cacheline and so corrupt the context object.

Secondary, leaving the context object as being marked in the CPU write
domain whilst on the GPU active list is a bad idea and will throw
warnings later.

Note: Thanks to calling set_to_gtt_domain with write = false and not
setting any gpu write domain when putting a context object onto the
active list (when we switch away from it) the set_to_gtt_domain call
won't block.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Added a note to the commit message and a comment in the code
to explain the clever non-blocking trick.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we take the struct_mutex lock to access the command-stream, there is
a possibility that we may need to wait for a GPU hang and so should make
the lock both interruptible and error-checking.

References: https://bugs.freedesktop.org/show_bug.cgi?id=50069Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we enable/disable the CPU backlight registers we can't forget to
enable/disable the PCH backlight registers. Since we're using the CPU
registers we should also unset the override bit.

Fixes a regression on the following commit:
  drm/i915: properly enable the blc controller on the right pipe

The commit just deleted the code that sets the PCH registers, so it
was relying on the values set by the BIOS. I told my BIOS to boot on
the DVI monitor instead of the LVDS panel, so I noticed the bug.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we drop the breadcrumb request after a batch due to a signal for
example we aim to fix it up at the next opportunity. In this case we
emit a second batchbuffer with no waits upon the first and so no
opportunity to insert the missing request, so we need to emit the
missing flush for coherency. (Note that that invalidating the render
cache is the same as flushing it, so there should have been no
observable corruption.)

Note that beside simply adding the missing flush, avoiding potential
render corruption, this will also fix at least parts of the problem
introduced by some funny interaction of these two commits:

commit de2b9985
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Jul 4 22:52:50 2012 +0200

    drm/i915: don't return a spurious -EIO from intel_ring_begin

which allowed intel_ring_begin to return -ERESTARTSYS and

commit cc889e0f
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Wed Jun 13 20:45:19 2012 +0200

    drm/i915: disable flushing_list/gpu_write_list

which essentially disabled the flushing list.

The issue happens when we submit a batch & emit it, but get
interrupted (thanks to the first patch) while trying to emit the
flush. On the next batch we still assume that the full gpu domain
handling is in effect and hence compute the invalidate&flushing
domains. But thanks to the 2nd patch we totally ignore these and only
invalidate all gpu domains, presuming that any required flushes have
been issued already.  Which is wrong and eventually results in us
updating the new write_domain values with the computed
pending_write_domain values, which leaves an object with write_domain
== 0 on the gpu_write_list.

As soon as we try to unbind that object, things blow up.

Fix this by emitting the missing flush according to the new
ring->gpu_caches_dirty flag.

Note that this does _not_ fix all the current cases where we end up
with an object on the flushing_list that can't be flushed.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=52040Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
[danvet: Add bug explanation to commit message.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Or going from tiled to untiled may break.
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While debugging Haswell link train failures I observed that we never
try the maximum voltage configuration more than once consecutively. We
start the training, the monitor keeps telling us to increase the
voltage, then when we reach the maximum we just go back to the start
(because of the "memset" above "voltage_tries = 0"). When we reach
this point, we keep alternating between the maximum and the minimum
voltages until we give up.

The DP spec suggests that we should try the same voltage 5 times
before giving up. This patch makes us try the maximum voltage at
least 5 times before going back to the minimum voltages.

This patch does not fix any particular bug I'm aware of.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have way too much lying hardware to rely on a simple "does someone
answer on the ddc i2c address?" check. And now it's unused, so just
kill it.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Somehow detect_ddc manages to fall through all checks when we think
that something responds on the ddc i2c address, but the edid read
failed. Fix this up by explicitly checking for this case.

This fixes a regression on newer chips because since

commit aaa37730
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Sat Jun 16 15:30:32 2012 +0200

    drm/i915/crt: Do not rely upon the HPD presence pin

we use ddc detection also on hotplug capable platforms. And one of
these reads all 0s for any i2c transaction if nothing is connected to
the vga port.

v2: Implement Chris Wilson's review:
- simplify logic, default to "nothing detected"
- kill stale comment
- BUG_ON(!crt->type != ANALOG)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=51900Tested-by: NYang Guang <guang.a.yang@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I so totally suck.

This can cause a black screen if (for whatever reason) the bios
hasn't set this bit itself.

This regression has been introduced in

commit 7cf41601
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Jun 5 10:07:09 2012 +0200

    drm/i915: clear up backlight #define confusion on gen4+
Tested-by: NKenneth Graunke <kenneth@whitecape.org>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Having had to dive into the bspec to understand what each stage of the
workaround meant, and how that the ring broadcasting IDLE corresponded
with the GT powering down the ring (i.e. rc6) add comments to aide
the next reader.

And since the register "is used to control all aspects of PSMI and power
saving functions" that makes it quite interesting to inspect with
regards to RC6 hangs, so add it to the error-state.

v2: Rediscover the piece of magic, set the RNCID to 0 before waiting for
the ring to wake up.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

It never quite worked despite the numerous workarounds, yet I still see
people trying to use this hardware and filing bug reports. As we no
longer even try to implement the workarounds, since 6a233c78
(drm/i915/ringbuffer: kill snb blt workaround), simply disable the ring.

v2: Add a message to inform the user about the limited capabilities of
their pre-production hardware.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This initializes power wells within the modeset_init_hw routine.
Testing has shown that this works for both driver load time and for
suspend-resume code paths.
Signed-off-by: NEugeni Dodonov <eugeni.dodonov@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There is little point waking up every 10ms to service an interrupt which
we then promptly ignore. So only program the the PMIER to enable
interrupts for those events which we do handle, not all of them!
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Eugeni Dodonov <eugeni.dodonov@intel.com>
Cc: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There were some fields missed. Daniel pointed this out in review, and I
know I fixed it, but something happened somehow and some time.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

*sigh* the docs had it spelled wrong, corrected it, and then proceeded
to re-do the original error. The original code preserved this history,
and this patch attempts to keep in sync with the current docs.
Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Userspace uses long in quite a few places more than the kernel. Which
gives me neat proof that I'm the only guy on this side of the galaxy
who ever tried to run glxgears on a 64bit machine with sis graphics on
linux.

Note that the longs in drm_sis_mem_t aren't aligned properly, so this
won't even work with 32bit userspace on 64bit kernel as-is. Hence the
patch can't break that, either.

Nope, I'm not nuts enough to write the 32bit ioctl compat layer for
this and test it with some wine app. Even though hunting the ebay
dungeons for a sis card actually supported by the mesa drivers casts
some doubts on this ...
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With the last patch to ditch DMA_QUEUE support, we should be able
to call the dma cleanup uncoditionally, even when the master has
disappeared.

Do so because it just makes more sense.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Absolutely unused. All the values are only ever initialized and
then used at most in some debug printout functions.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Only one driver (i810) even sets that flag. Now the actual locking
code uncoditionally promotes lock->context to an unsigned int.

Closer inspection of the userspace reveals that the drm lock context
is defined as an unsigned int (at least on linux). I suspect we just
have a strange case of signedness confusion going on.

Tested on my i815, doesn't seem to break anything.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

All leftover users either haven't set DRIVER_HAVE_DMA, in which
case this will never be called, or use the drm_core implementation.

Call that directly in the only callsite.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The reclaim_buffers function of the savage driver actually wants to run
with the hw_lock held - at least there are printks in the call-chain
to that effect. But the drm core only calls reclaim_buffers as used
by savage _after_ forcefully dropping the hwlock (in case it's still
hold by the closing fd).

So do the same idlelock dance as for the other dma drivers and hope
that papers over any issues.

v2: Don't let the idlelock linger around.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Tested-by: NTormod Volden <debian.tormod@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

i810 was the last user of this code, with that gone, kill it.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 6e877b57,
reinstating the original commit:

commit 87499ffd
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date:   Tue Oct 25 23:51:24 2011 +0200

    drm/i810: cleanup reclaim_buffers

    My dear old i815 always hits the deadlocked on reclaim_buffers
    warning. Switch over to the idlelock duct-tape on hope that
    works better. I've fired up my i815 and now closing glxgears doesn't
    take 5 seconds anymore. \o/

The original problem with that was that I've moved it ahead in the
series so that it could be included despite some patches not being
ready quite yet. The little problem is that this patch required some
of the previous rework to work correctly.

Now that everything is in the right order again, this actually works
on my i810 and does speed up closing gl apps as the original commit
claimed. Without hanging the machine, as the revert says.
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The only two users are now folded into the drivers preclose functions,
so this is unused.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Like for via.

v2: Actually drop the idlelock again if taken.

v3: Fixup.

v4: Fixup the "has master" vs. "is master" confusion the refactor
introduced.

v5: Drop the idlelock in the early return path.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

A few things
- kill reclaim_buffers, it's never ever called because via does not set
  DRIVER_HAVE_DMA
- inline the idlelock dance into the buffer reclaim logic and make it
  a simple preclose cleanup function
- directly call the the dma_quiescent function and kill the needless
  if check.

v2: Actually drop the idlelock when we take it. Reported by James
Simmons.

v3: Rebased onto latest drm-next.

v4: Fixup the refactor.

v5: More fixup the refactor - I've accidentally changed the check for
any master to checking whether the closing fd is the master.

v6: Don't forget to drop the idlelock in the early return path, too.
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This ports over the dpms code from udlfb, and should mean
a better chance of turning on some udl devices.
Signed-off-by: NDave Airlie <airlied@redhat.com>