The dw_mmc driver does not take into account the processor may be in
big endian when writing the descriptors. Change the descriptors for
the 32bit IDMA to use __le32 and ensure they are suitably swapped
before writing.

Note, this has not been tested as the socfpga driver does not try to
use idma.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The dw_mmc driver does not use endian agnostic IO accessors, so fix
the use of __raw reads and writes to be the relaxed versions.

This fixes the dw_mmc driver initialisation on Altera socfpga in big endian.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Also check MMC OF properties. The controller supports MMC too.
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

rts5250 chip failed handle 64 bit ADMA for address below 4G.
Add 64 BIT quirks to disable this feature.
Signed-off-by: NMicky Ching <micky_ching@realsil.com.cn>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:

		mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
 				EXT_CSD_HPI_MGMT, 1,
 				card->ext_csd.generic_cmd6_time);

There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Modify the driver to handle GPIOs using the descriptor API.
Signed-off-by: NMylene JOSSERAND <josserand.mylene@gmail.com>
Reviewed-by: NAlexandre Courbot <acourbot@nvidia.com>
Tested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

strip the card dectet logic from cover detect isr and vice versa
the generic mmc_gpio_cd_irqt isr, uses 200ms on removal/insertion,
hence that should be fine here as well
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If dw_mci_init_slot() returns that we got a probe deferral then it may
leave slot->mmc as NULL.  That will cause dw_mci_enable_cd() to crash
when it calls mmc_gpio_get_cd().

Fix this by moving the call of dw_mci_enable_cd() until we're sure
that we're good.  Note that if we have more than one slot and one
defers (but the others don't) things won't work so well.  ...but
that's not a new thing and everyone has already agreed that multislot
support ought to be removed from dw_mmc eventually anyway since it is
unused, untested, and you can see several bugs like this by inspecting
the code.

Fixes: bcafaf5470f0 ("mmc: dw_mmc: Only enable CD after setup and only if needed")
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

In the Designware databook's description of the "Voltage Switch Normal
Scenario" it instructs us to set a timer and fail the voltage change
if we don't see the voltage change interrupt within 2ms.  Let's
implement that.  Without implementing this I have often been able to
reproduce a hang while trying to send CMD11 on an rk3288-based board
while constantly ejecting and inserting UHS cards.
Signed-off-by: NDoug Anderson <dianders@chromium.org>
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Enable card-read-threshold, when eMMC mode is HS400.
Refer to f1d2736c (mmc: dw_mmc: control card read threshold)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Currently those host drivers which have deployed runtime PM, deals with
the runtime PM reference counting entirely by themselves.

Since host drivers don't know when the core will send the next request
through some of the host_ops callbacks, they need to handle runtime PM
get/put between each an every request.

In quite many cases this has some negative effects, since it leads to a
high frequency of scheduled runtime PM suspend operations. That due to
the runtime PM reference count will normally reach zero in-between
every request.

We can decrease that frequency, by enabling the core to deal with
runtime PM reference counting of the host device. Since the core often
knows that it will send a seqeunce of requests, it makes sense for it
to keep a runtime PM reference count during these periods.

More exactly, let's increase the runtime PM reference count by invoking
pm_runtime_get_sync() from __mmc_claim_host(). Restore that action by
invoking pm_runtime_mark_last_busy() and pm_runtime_put_autosuspend()
in mmc_release_host(). In this way a runtime PM reference count will be
kept during the complete cycle of a claim -> release host.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NAdrian Hunter <adrian.hunter@intel.com>
Acked-by: NKonstantin Dorfman <kdorfman@codeaurora.org>

board-rx51 has no card detect pin in the mmc slot, but can detect that
the (cell-phone) cover has been removed and the card is accessible.
The semantics between cover/card detect differ, the gpio on the slot
informs you after the card has been removed, cover removal does not
necessarily mean that the card has been removed.
This means different code paths are necessary. To complete this we
also want different fields in the platform data for cover and card
detect. This separation is not pushed all the way down into struct
omap2_hsmmc_info which is used to initialize the platform data.
If we did that we had to go over all board files and set the new
gpio_cod pin to -EINVAL. If we forget one board or some out-of-tree
archicture forgets that the default '0' is used which is a valid pin
number.
Signed-off-by: NAndreas Fenkart <afenkart@gmail.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

These callbacks have been set to deprecated for some time. The last
user (omap_hsmmc) has moved away from using them, which thus enables
us to completely remove them.
Signed-off-by: NNeilBrown <neil@brown.name>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The ->enable|disable() callbacks are only used to get and put runtime
PM references. Currently omap_hsmmc's ->set_ios() already does this
itself.

Other host drivers deals with runtime PM without using the
->enable|disable() callbacks and thus do the runtime PM reference
counting themselves. Apply that approach for omap_hsmmc as well and
then discard the ->enable|disable() callbacks.
Signed-off-by: NNeilBrown <neil@brown.name>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some versions of this controller do not advertise their 3.0v and
8bit bus-width support capabilities. It is required to explicitly
set these capabilities for the specific controller versions.
Signed-off-by: NGeorgi Djakov <georgi.djakov@linaro.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Signed-off-by: NBjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Change the __raw IO functions to endian agnostic relaxed ones to allow
the driver to function on big endian ARM systems.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().

To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NNeilBrown <neil@brown.name>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When the sunxi mmc-controller code was initially merged MMC_CAP_SDIO_IRQ was
not added to the host caps because of issues with some sdio wifi modules.

It turns out that these issues have nothing to do with using sdio-irq support,
they also happen with oob interrupts. Since the hardware supports sdio-irq
everywhere, and since the one reason to not claim the capability is gone,
add MMC_CAP_SDIO_IRQ to the default host caps.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The driver co-allocates sdhci_iproc_host with sdhci_pltfm_host and so to
access it we need to use sdhci_pltfm_priv() and not pltfm_host->priv.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sdhci_request function should consider a non-removable device
always present.
Call the correct logic already available in sdhci_do_get_cd function.

This fixes some logic paths where MMC requests are being made to
non-removable devices that do not have the card detect pin connected
on the hardware as it is non-removable.
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Move the member for card_int_gpio into the struct spear_sdhci.

In this way we eliminate the last user of the struct sdhci_plat_data,
which enables us to remove the exported header for sdhci-spear.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This driver is used on SoCs which are using CONFIG_OF. By adding a
compile dependency in the Kconfig, it enables us to simplify some code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since there no users of the struct sdhci_host, but the shdci host
drivers themselves, let's move the definition of it to the local sdhci
header.

The exported sdhci header then becomes empty, so let's remove it.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Since commit cd1e6504 ("of/device: Don't register disabled
devices"), the disabled device will not be registered at all. So
we don't need to do the check again in the platform device driver.

And the check in the current code is useless even if we really
run into a disabled device. In this case, it just doesn't parse
the dtb for the infos such as quirks or clock, but it will continue
to try to init the disabled device after that check. So just remove it.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Setup a different set of sdhci_ops for tegra114 and later so that
the write_w callback is only used on tegra114. This allows us to
remove the NVQUIRK_SHADOW_XFER_MODE_REG and simply the logic
in tegra_sdhci_writew.
Suggested-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A command end interrupt should not be processed between command issue
and setting of wait_for flag. It expects already the flag to be set.
Therefore the exclusive control was added.
Signed-off-by: NKouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If interruption of command already occurred, mrq pointer in dev_err()
would refer to NULL, because the host-state is changed to STATE_IDLE
and mrq pointer is changed to NULL by interrupt handler.
Therefore dev_err is moved after checking STATE_IDLE.
Signed-off-by: NKouichi Tomita <kouichi.tomita.yn@renesas.com>
Signed-off-by: NYoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It was brought to my attention that the sdhci-pxav3 driver is needed
on a few more ARM machines than I initially thought. Add the missing
architectures to the dependency list.

Credits to Peter Robinson for noticing my mistake and reporting.
Reported-by: NPeter Robinson <pbrobinson@gmail.com>
Signed-off-by: NJean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The alloc() and free() hooks required each pwrseq implementation to set
host->pwrseq themselves. This is error-prone and could be done at a
higher level if alloc() was changed to return a pointer to a struct
mmc_pwrseq instead of an error code.

This patch performs this change and moves the burden of maintaining
host->pwrseq from the power sequence hooks to the pwrseq code.
Signed-off-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sunxi mmc driver tries to calculate a dma address by using pointer
arithmetic, which causes a warning when dma_addr_t is wider than a pointer:

drivers/mmc/host/sunxi-mmc.c: In function 'sunxi_mmc_init_idma_des':
drivers/mmc/host/sunxi-mmc.c:296:35: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
  struct sunxi_idma_des *pdes_pa = (struct sunxi_idma_des *)host->sg_dma;
                                   ^

To avoid this warning and to simplify the logic, this changes
the code to avoid the cast and calculate the correct address
manually. The behavior should be unchanged.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NDavid Lanzendörfer <david.lanzendoerfer@o2s.ch>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add IPROC SDHCI driver for IPROC family of Broadcom devices.
Acked-by: NRay Jui <rjui@broadcom.com>
Signed-off-by: NCorneliu Doban <cdoban@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

For CMD53 in block mode, the host does not need to stop the transfer,
as it stops when the block count (present in CMD53) is reached.
Signed-off-by: NCorneliu Doban <cdoban@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add quirk to handle broken auto-CMD23.
Some controllers do not respond after the first auto-CMD23 is issued.

This allows CMD23 to still work (mandatory for the faster UHS-I mode)
rather than disabling CMD23 entirely via SDHCI_QUIRK2_HOST_NO_CMD23.

Signed-off by: Corneliu Doban <cdoban@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Static checkers suggest that probably we intended to put curly braces
around the writel() to make it part of the else path.  But, I think
actually the indenting is off and the code works fine as is.

The stray tab was introduced in 0322191e ('mmc: sdhci-esdhc-imx: add
sd3.0 SDR clock tuning support')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NDong Aisheng <b29396@freescale.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

If CONFIG_DEBUG_SLAB=y:

    sh_mobile_sdhi ee100000.sd: Got CD GPIO
    sh_mobile_sdhi ee100000.sd: Got WP GPIO
    platform ee100000.sd: Driver sh_mobile_sdhi requests probe deferral
    ...
    Slab corruption (Not tainted): kmalloc-1024 start=ed8b3c00, len=1024
    2d0: 00 00 00 00 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  ....kkkkkkkkkkkk
    Prev obj: start=ed8b3800, len=1024
    000: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk
    010: 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b 6b  kkkkkkkkkkkkkkkk

Struct tmio_mmc_host is embedded inside struct mmc_host, and thus is
freed by the call to mmc_free_host(). Hence it must not be written to
afterwards, as that will corrupt freed (and perhaps already reused)
memory.

Fixes: 94b110af ("mmc: tmio: add tmio_mmc_host_alloc/free()")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>