Unfortunately we don't know all panels and platforms out there and we
found internal prototypes without VBT proper set but where only
link in standby worked well.

So, before enable PSR by default let's instrument the PSR parameter
in a way that we can identify different panels out there that might
require or work better with link standby mode.

It is also useful to say that for backward compatibility I'm not
changing the meaning of this flag. So "0" still means disabled
and "1" means enabled with full support and maximum power savings.

v2: Use positive value instead of negative for different operation mode
    as suggested by Daniel.

v3: As Paulo suggested use 2 to force link standby and 3 to force link
    fully on. Also split the link_standby introduction in a separated patch.

v4: Use DRM_ERROR for link off request on platforms that don't support and
    Remove the quirk promise.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454356928-19779-1-git-send-email-rodrigo.vivi@intel.com

Link standby support has been deprecated with 'commit 89251b17
("drm/i915: PSR: deprecate link_standby support for core platforms.")'

The reason for that is that main link in full off offers more power
savings and on HSW and BDW implementations on source side had known
bugs with link standby.

However that same HSD report only mentions BDW and HSW and tells that
a fix was going to new platforms. Since on Skylake link standby
didn't cause the bad blank flickering screens seen on HSW and BDW
let's respect VBT again for this and future platforms.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

Current code not just block link_standby for non DDI platforms but also
block PSR from work on other ports B/C/D/E.

So, besides change any behaviour let's just fix the mess a bit here and
reuse HSW check to block the other ports and reduce the second if only to
link stadnby request.

Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>

The driver does not load firmware for unknown steppings, so these new
steppings must be added to the list.

Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454023163-25469-1-git-send-email-mathew.j.martineau@linux.intel.com

When we stop the sink CRC calculation we wait a while until the counter
is reset to zero and return -ETIMEDOUT. However the sink crc was
calculated already by this point so we just ignore this return at
the main function.

So, let's also ignore the message and put it as a debug message instead
of an error one. The message might still be useful when debuging
test failures so we could be able to know something was not going so
well with sink crc stop.

v2: Improve log message.

Reference: https://bugs.freedesktop.org/show_bug.cgi?id=93694
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454107499-29678-1-git-send-email-rodrigo.vivi@intel.com

The FBC fixes we've been doing in the last months required a lot of
refactor, so functions that were once big and called from different
spots are now small and called only once. IMHO now it's better to just
move the contents of these functions to their only callers since this
reduces the number of indirections while reading the code.

While at it, also improve the related comments a little bit.
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-26-git-send-email-paulo.r.zanoni@intel.com

We already make sure we run intel_fbc_update_update during modesets
and page flips, and this function takes care of deactivating FBC, so
it shouldn't be possible for us to reach the condition we check at
intel_fbc_work_fn. So instead of grabbing framebuffer references and
adding a lot of code to track when we need to free them, just don't
track anything at all since we shouldn't need to.

v2: Rebase.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-25-git-send-email-paulo.r.zanoni@intel.com

Make sure we do the pre_update - which also deactivates FBC - before
we actually schedule the page flip, just to make sure we don't
flip to the new FB with FBC still activated for the previous FB.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-24-git-send-email-paulo.r.zanoni@intel.com

We don't actually use fb_id anywhere. We already compare all
parameters that matter to the hardware: pixel format, stride,
fence_reg and ggtt_offset. The ID shouldn't make a difference.

Besides, we already update the FBC data at every modeset/flip, so this
can't change behind our backs.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-23-git-send-email-paulo.r.zanoni@intel.com

Our dmesg messages started being misleading after we converted to the
enable+activate model: we always print "Disabling FBC", even when
we're just deactivating it. So, for example, when I boot my machine
and do "dmesg | grep -i fbc", I see:
  [drm:intel_fbc_enable] Enabling FBC on pipe A
  [drm:set_no_fbc_reason] Disabling FBC: framebuffer not tiled or fenced
but then, if I read the debugfs file, I will see:
  $ sudo cat i915_fbc_status
  FBC enabled
  Compressing: yes
so we can conclude that dmesg is misleading, since FBC is actually
enabled. What happened is that we deactivated FBC due to fbcon not
being tiled, but when we silently reactivated it when the display
manager started. We don't print activation messages since there may be
way too many of these operations per second during normal desktop
usage.

One possible solution would be to change set_no_fbc_reason to
correctly differentiate between disable and deactivation, but we
removed support from printing activation/deactivation messages in the
past because they were too frequent. So instead of doing this, let's
just not print anything on dmesg, and leave the debugfs file if the
user needs to investigate something. We already print when we enable
and disable FBC anyway on a given pipe, so this should already help
triaging bugs.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-22-git-send-email-paulo.r.zanoni@intel.com

During FBC invalidation, don't call intel_fbc_deactivate if it's not
enabled. This doesn't fix any bug, but helps making the interface
saner.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-21-git-send-email-paulo.r.zanoni@intel.com

Move intel_fbc_enable to a place where it is called regardless of the
"modeset" variable, and make sure intel_fbc_enable can be called
multiple times without intel_fbc_disable being called.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-20-git-send-email-paulo.r.zanoni@intel.com

Instead of duplicating the calls for every platform, let's just put
them in the correct places inside intel_atomic_commit. This will also
make it easier for us to move the enable call in order to support
fasbtoot.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-19-git-send-email-paulo.r.zanoni@intel.com

This opens the possibility of implementing nicer schemes to choose the
CRTC, such as checking the amount of stolen memory available, or
choosing the best pipe on platforms that don't die FBC to pipe or
plane A.

This code was written for another refactor that I ended up discarding,
so I don't actually need it, but I figured this patch would be an
improvement on its own so I kept it on the series.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-18-git-send-email-paulo.r.zanoni@intel.com

We already have a dev variable, there's no need to access state->dev.
Also, I plan to add another dev_priv user here, so declare one for the
current user.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-17-git-send-email-paulo.r.zanoni@intel.com

Older FBC platforms have this restriction where FBC can't be enabled
if multiple pipes are enabled. In the current code, we disable FBC
before the second pipe becomes visible.

One of the problems with this code is that the current
multiple_pipes_ok() implementation just iterates through all CRTCs
looking at their states, but it doesn't make sure that the state
locks are grabbed. It also can't just grab the locks for every CRTC
since this would kill one of the biggest advantages of atomic
modesetting.

After the recent FBC changes, we now have the appropriate locks for
the given CRTC, so we can just try to maintain the state of each CRTC
and update it once intel_fbc_pre_update is called.

As a last note, I don't have gen 2/3 machines to test this code. My
current plan is to enable FBC on just the newer platforms, so this
patch is just an attempt to get the gen 2/3 code at least looking
sane, so if one day someone decide to fix FBC on these platforms, they
may have less work to do.

Not-tested-by: Paulo Zanoni <paulo.r.zanoni@intel.com> (only on HSW+)
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-16-git-send-email-paulo.r.zanoni@intel.com

Just to be sure nothing will survive a module unload. We need to do
this after the unlock in order to make sure the function won't get
stuck trying to grab the lock we already own while we wait for it to
finish.
Reported-by: NReported-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-15-git-send-email-paulo.r.zanoni@intel.com

Instead of:
 - intel_fbc_disable_crtc(crtc)
 - intel_fbc_disable(dev_priv)
we now have:
 - intel_fbc_disable(crtc)
 - intel_fbc_global_disable(dev_priv)

This is because all the other functions that take a CRTC are called
 - intel_fbc_something(crtc)
Instead of:
 - intel_fbc_something_crtc(crtc)

And I also hope that the word "global" is going to help make it more
explicit that "global" is the unusual case, not the opposite.
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-14-git-send-email-paulo.r.zanoni@intel.com

With the addition and usage of intel_fbc_pre_update,
intel_fbc_deactivate is not used anymore outside intel_fbc.c, so kill
the exported function and rename __intel_fbc_deactivate.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-13-git-send-email-paulo.r.zanoni@intel.com

We'll now call intel_fbc_pre_update instead of intel_fbc_deactivate
during atomic commits. This will continue to guarantee that we
deactivate FBC and it will also update the state checking structures
at the correct time. Then, later, at the point where we were calling
intel_fbc_update, we'll only need to call intel_fbc_post_update.

Also add the proper warnings in case we don't have the appropriate
locks. Daniel mentioned the warnings will have to be removed for async
commits, but let's keep them here while we can.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-12-git-send-email-paulo.r.zanoni@intel.com

So now pre_update will be responsible for unconditionally deactivating
FBC and updating the state cache, while post_update will be
responsible for checking if it can be enabled, then enabling it.

This is one more step into proper locking.

Notice that intel_fbc_flush now calls post_update directly. The FBC
flush can only happen for drawing operations - since we explicitly
ignore the flips -, so the FBC state is not expected to have changed
at this point. With this we can just run post_update, which will make
sure we won't deactivate+reactivate FBC as would be the case now if we
called pre_update + post_update.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-11-git-send-email-paulo.r.zanoni@intel.com

Per the new atomic locking rules, we need to cache the CRTC, plane and
FB state structures we use so we can access them later without needing
more locks. So do this.

Notice that there are some pieces of the FBC code that look at things
that are only computed during the modeset, so we can't just can't
precompute whether FBC can be activated during the update_state_cache
stage. We may be able to do this later.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-10-git-send-email-paulo.r.zanoni@intel.com

We unconditionally disable/update FBC even during the page flip
IOCTLs, and an unconditional disable/update at every atomic commit
touching the primary plane shouldn't impact PC state residency
noticeably. Besides, the code that checks for rotation is a good hint
that we may be forgetting something else, so let's leave all the
decisions to intel_fbc.c, making the code much safer.

Once we have the code to properly make FBC enable/update decisions
based on atomic states, with proper locking, then we'll be able to
evaluate whether it will be worth trying to optimize the cases where a
disable isn't needed.

v2: Upstream moved and now our patch needs to remove dev_priv.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406837-10511-1-git-send-email-paulo.r.zanoni@intel.com

If frontbuffer_bits doesn't match the current frontbuffer, there's no
reason to recompress or update FBC.

There was a plan to make the FBC test suite catch this type of
problem, but it never got implemented due to being low priority.

While at it, also implement Ville's suggestion and use
plane->frontbuffer_bit instead of INTEL_FRONTBUFFER_PRIMARY.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-8-git-send-email-paulo.r.zanoni@intel.com

Before this patch, page flips would call intel_frontbuffer_flip() and
intel_frontbuffer_flip_complete(), which would call intel_fbc_flush(),
which would call intel_fbc_update(). The problem is that drawing
operations also trigger intel_fbc_flush() calls, so it's not
guaranteed that we have the CRTC and FB locks grabbed when
intel_fbc_flush() happens, since the call trace may come from the
rendering path.

We're trying to make the FBC code grab the appropriate CRTC/FB locks,
so split the drawing and the flipping logic in order to achieve that
in later patches. So now the frontbuffer tracking code is just going
to be used for frontbuffer drawing, and intel_fbc_update() is going to
be used directly for actual page flips.

As a note, we don't need to call intel_fbc_flip() during the two
places where we call intel_frontbuffer_flip() since in one of them we
already have an intel_fbc_update() call, and in the other we have the
planes disabled.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-7-git-send-email-paulo.r.zanoni@intel.com

We say "dev_priv->fbc.something" way too many times in our code while
we could be saying just "fbc->something" with a previous declaration
of fbc. This has been bothering me for a while but I didn't want to
patch it since I wanted to fix the real problems first. But as I add
more code I keep thinking about it, especially since it makes the code
easier to read and it can make us fit 80 columns easier, so let's just
do the change now.

While at it, also rename from i915_fbc to intel_fbc because the whole
FBC code uses intel_fbc.

v2: Rebase after the work_fn changes.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406763-10400-1-git-send-email-paulo.r.zanoni@intel.com

The early return inside __intel_fbc_update does not completely check
all the parameters that affect the FBC register values. For example,
we currently lack looking at crtc->adjusted_y (for the fence Y offset)
and all the parameters that affect the CFB size (for i8xx).

Instead of just adding the missing parameters to the check and hoping
that any changes to the fbc_activate functions also come with a
matching change to the __intel_fbc_update check, introduce a new
structure where we store these parameters and use the structure at the
fbc_activate function. Of course, it's still possible to access
everything from dev_priv in those functions, but IMHO the new code
will be harder to break.

v2: Rebase.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-5-git-send-email-paulo.r.zanoni@intel.com

Make our enable/activate checking model more explicit, especially
since we now have intel_fbc_can_activate().
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-4-git-send-email-paulo.r.zanoni@intel.com

Extract all the code that checks if the FBC configuration is valid to
its own function, making __intel_fbc_update() much simpler.
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453210558-7875-3-git-send-email-paulo.r.zanoni@intel.com

Instead of waiting for 50ms, just wait until the next vblank, since
it's the minimum requirement. The whole infrastructure of FBC is based
on vblanks, so waiting for X vblanks instead of X milliseconds sounds
like the correct way to go. Besides, 50ms may be less than a vblank on
super slow modes that may or may not exist.

There are some small improvements in PC state residency (due to the
fact that we're now using 16ms for the common modes instead of 50ms),
but the biggest advantage is still the correctness of being
vblank-based instead of time-based.

v2:
  - Rebase after changing the patch order.
  - Update the commit message.
v3:
  - Fix bogus vblank_get() instead of vblank_count() (Ville).
  - Don't forget to call drm_crtc_vblank_{get,put} (Chris, Ville)
  - Adjust the performance details on the commit message.
v4:
  - Don't grab the FBC mutex just to grab the vblank (Maarten)
Signed-off-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453406585-10233-1-git-send-email-paulo.r.zanoni@intel.com

No functional change
Signed-off-by: NMat Martineau <mathew.j.martineau@linux.intel.com>
Fixes: f8d03ea0 ("drm/i915: increase the tries for HDMI hotplug live status checking")
Link: http://patchwork.freedesktop.org/patch/msgid/1454023325-26265-1-git-send-email-mathew.j.martineau@linux.intel.comSigned-off-by: NJani Nikula <jani.nikula@intel.com>

The test for the qemu q35 south bridge added by commit
"39bfcd52 drm/i915: more virtual south bridge detection"
also matches on real hardware.  Having the check for
virtual systems last in the list is not enough to avoid
that ...

Refine the check by additionally verifying the pci
subsystem id to see whenever it *really* is qemu.

[ v2: fix subvendor tyops ]
Reported-and-tested-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Tested-by: NBruno Wolff III <bruno@wolff.to>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453719748-10944-1-git-send-email-kraxel@redhat.com

The fb_modifiers and cpp arguments passed to intel_tile_width() in
intel_fill_fb_ggtt_view() got accidentally swapped around. I'm pretty
sure I fixed this already, but could be I lost the fix accidentally
during some rebases or something. Anyway, fix it up for real.

Fixes: d9b3288e ("drm/i915: change intel_fill_fb_ggtt_view() to use the real tile size")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-8-git-send-email-ville.syrjala@linux.intel.com
Testcase: igt/kms_rotation_crc/primary-rotation-90
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Cc: drm-intel-fixes@lists.freedesktop.org

We more or less randomly call the "bytes per pixel" value
'cpp', 'bytes_per_pixel', 'pixel_size', or even 'bpp'. Let's just pick
one and stick to it. I've chosen 'cpp'.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Using 'unsigned long' for ggtt offsets doesn't make much sense. Use
'u32' instead since we've not yet seen a >4GiB ggtt.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

intel_rotate_fb_obj_pages() doens't need the entire gtt view, just the
rotation info suffices.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Pass stride in addition to width and height to rotate_pages(). For now
width and stride are the same, but once framebuffer offsets enter the
scene that may no longer be the case.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Also rename 'rotation_info' to 'rotated' to match the view type exactly,
this should avoid confusion which union members is valid for each view
type.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453316739-13296-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the error-handling paths of i915_gem_do_execbuffer() and
intel_crtc_page_flip(), the local pointer-to-request variables
were expected to be either valid pointers or NULL. Since

  26827088 drm/i915: simplify allocation of driver-internal requests

they could also be ERR_PTR() values, so the tests need to be
updated to accommodate this case.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453978089-29127-1-git-send-email-tvrtko.ursulin@linux.intel.com

In GuC mode LRC pinning lifetime depends exclusively on the
request liftime. Since that is terminated by the seqno update
that opens up a race condition between GPU finishing writing
out the context image and the driver unpinning the LRC.

To extend the LRC lifetime we will employ a similar approach
to what legacy ringbuffer submission does.

We will start tracking the last submitted context per engine
and keep it pinned until it is replaced by another one.

Note that the driver unload path is a bit fragile and could
benefit greatly from efforts to unify the legacy and exec
list submission code paths.

At the moment i915_gem_context_fini has special casing for the
two which are potentialy not needed, and also depends on
i915_gem_cleanup_ringbuffer running before itself.

v2:
 * Move pinning into engine->emit_request and actually fix
   the reference/unreference logic. (Chris Wilson)

 * ring->dev can be NULL on driver unload so use a different
   route towards it.

v3:
 * Rebase.
 * Handle the reset path. (Chris Wilson)
 * Exclude default context from the pinning - it is impossible
   to get it right before default context special casing in
   general is eliminated.

v4:
 * Rebased & moved context tracking to
   intel_logical_ring_advance_and_submit.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Issue: VIZ-4277
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nick Hoath <nicholas.hoath@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1453976997-25424-1-git-send-email-tvrtko.ursulin@linux.intel.com