The driver currently support only vlan priority zero. So map the
vlan priorities to zero flow in hardware.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce rgmii link status to handle link state events for 2u
cpsw hardware on K2G.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

2u cpsw hardware on K2G uses rgmii link to interface with Phy. So add
support for this interface in the code so that driver can be re-used
for 2u hardware.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As a preparatory patch to add support for 2u cpsw hardware found on
K2G SoC, make sgmii configuration conditional. This is required
since 2u uses RGMII interface instead of SGMII and to allow for driver
re-use.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver currently uses macro for NU and XBE hardwrae, while other
places for older hardware such as that on K2H/K SoC (version 1.4
of the cpsw hardware, it explicitly check for the ss_version
inline. Add a new macro for version 1.4 and use it to customize
code in the driver. While at it also fix similar issue with
checking XBE version by re-using existing macro IS_SS_ID_XGBE().
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch provide APIs to allow client drivers to support
probe deferral. On K2G SoC, devices can be probed only
after the ti_sci_pm_domains driver is probed and ready.
As drivers may get probed at different order, any driver
that depends on knav dma and qmss drivers, for example
netcp network driver, needs to defer probe until
knav devices are probed and ready to service. To do this,
add an API to query the device ready status from the knav
dma and qmss devices.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Navigator Subsystem (NAVSS) available on K2G SoC has a cut down
version of QMSS with less number of queues, internal linking ram
with lesser number of buffers etc.  It doesn't have status and
explicit push register space as in QMSS available on other K2 SoCs.
So define reg indices specific to QMSS on K2G. This patch introduces
"ti,66ak2g-navss-qm" compatibility to identify QMSS on K2G NAVSS
and to customize the dts handling code. Per Device manual,
descriptors with index less than or equal to regions0_size is in region 0
in the case of K2 QMSS where as for QMSS on K2G, descriptors with index
less than regions0_size is in region 0. So update the size accordingly in
the regions0_size bits of the linking ram size 0 register.
Signed-off-by: NMurali Karicheri <m-karicheri2@ti.com>
Signed-off-by: NWingMan Kwok <w-kwok2@ti.com>
Reviewed-by: NRob Herring <robh@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David Ahern says:

====================
net/ipv6: Separate data structures for FIB and data path

IPv6 uses the same data struct for both control plane (FIB entries) and
data path (dst entries). This struct has elements needed for both paths
adding memory overhead and complexity (taking a dst hold in most places
but an additional reference on rt6i_ref in a few). Furthermore, because
of the dst_alloc tie, all FIB entries are allocated with GFP_ATOMIC.

This patch set separates FIB entries from dst entries, better aligning
IPv6 code with IPv4, simplifying the reference counting and allowing
FIB entries added by userspace (not autoconf) to use GFP_KERNEL. It is
first step to a number of performance and scalability changes.

The end result of this patch set:
  - FIB entries (fib6_info):
        /* size: 208, cachelines: 4, members: 25 */
        /* sum members: 207, holes: 1, sum holes: 1 */

  - dst entries (rt6_info)
       /* size: 240, cachelines: 4, members: 11 */

Versus the the single rt6_info struct today for both paths:
      /* size: 320, cachelines: 5, members: 28 */

This amounts to a 35% reduction in memory use for FIB entries and a
25% reduction for dst entries.

With respect to locking FIB entries use RCU and a single atomic
counter with fib6_info_hold and fib6_info_release helpers to manage
the reference counting. dst entries use only the traditional dst
refcounts with dst_hold and dst_release.

FIB entries for host routes are referenced by inet6_ifaddr and
ifacaddr6. In both cases, additional holds are taken -- similar to
what is done for devices.

This set is the first of many changes to improve the scalability of the
IPv6 code. Follow on changes include:
- consolidating duplicate fib6_info references like IPv4 does with
  duplicate fib_info

- moving fib6_info into a slab cache to avoid allocation roundups to
  power of 2 (the 208 size becomes a 256 actual allocation)

- Allow FIB lookups without generating a dst (e.g., most rt6_lookup
  users just want to verify the egress device). Means moving dst
  allocation to the other side of fib6_rule_lookup which again aligns
  with IPv4 behavior

- using separate standalone nexthop objects which have performance
  benefits beyond fib_info consolidation

At this point I am not seeing any refcount leaks or underflows, no
oops or bug_ons, or warnings from kasan, so I think it is ready for
others to beat up on it finding errors in code paths I have missed.

v2 changes
- rebased to top of tree
- improved commit message on patch 7

v1 changes
- rebased to top of tree
- fix memory leak of metrics as noted by Ido
- MTU fixes based on pmtu tests (thanks Stefano Brivio for writing)

RFC v2 changes
- improved commit messages
- move common metrics code from dst.c to net/ipv4/metrics.c (comment
  from DaveM)
- address comments from Wei Wang and Martin KaFai Lau (let me know if
  I missed something)
- fixes detected by kernel test robots
  + added fib6_metric_set to change metric on a FIB entry which could
    be pointing to read-only dst_default_metrics
  + 0day testing found a problem with an intermediate patch; added
    dst_hold_safe on rt->from. Code is removed 3 patches later
- allow cacheinfo to handle NULL dst; means only expires is pushed to
  userspace
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Drop unneeded elements from rt6_info struct and rearrange layout to
something more relevant for the data path.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert all code paths referencing a FIB entry from
rt6_info to fib6_info.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Last step before flipping the data type for FIB entries:
- use fib6_info_alloc to create FIB entries in ip6_route_info_create
  and addrconf_dst_alloc
- use fib6_info_release in place of dst_release, ip6_rt_put and
  rt6_release
- remove the dst_hold before calling __ip6_ins_rt or ip6_del_rt
- when purging routes, drop per-cpu routes
- replace inc and dec of rt6i_ref with fib6_info_hold and fib6_info_release
- use rt->from since it points to the FIB entry
- drop references to exception bucket, fib6_metrics and per-cpu from
  dst entries (those are relevant for fib entries only)
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add fib6_info struct and alloc, destroy, hold and release helpers.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IPv6 FIB will only contain FIB entries with exception routes added to
the FIB entry. Once this transformation is complete, FIB lookups will
return a fib6_info with the lookup functions still returning a dst
based rt6_info. The current code uses rt6_info for both paths and
overloads the rt6_info variable usually called 'rt'.

This patch introduces a new 'f6i' variable name for the result of the FIB
lookup and keeps 'rt' as the dst based return variable. 'f6i' becomes a
fib6_info in a later patch which is why it is introduced as f6i now;
avoids the additional churn in the later patch.

In addition, remove RTF_CACHE and dst checks from fib6 add and delete
since they can not happen now and will never happen after the data
type flip.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most FIB entries can be added using memory allocated with GFP_KERNEL.
Add gfp_flags to ip6_route_add and addrconf_dst_alloc. Code paths that
can be reached from the packet path (e.g., ndisc and autoconfig) or
atomic notifiers use GFP_ATOMIC; paths from user context (adding
addresses and routes) use GFP_KERNEL.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The router discovery code has a FIB entry and wants to validate the
gateway has a neighbor entry. Refactor the existing dst_neigh_lookup
for IPv6 and create a new function that takes the gateway and device
and returns a neighbor entry. Use the new function in
ndisc_router_discovery to validate the gateway.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Continuing to wean FIB paths off of dst_entry, use a bool to hold
requests for certain dst settings. Add a helper to convert the
flags to DST flags when a FIB entry is converted to a dst_entry.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_pol_route_lookup is the lookup function for ip6_route_lookup and
rt6_lookup. At the moment it returns either a reference to a FIB entry
or a cached exception. To move FIB entries to a separate struct, this
lookup function needs to convert FIB entries to an rt6_info that is
returned to the caller.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ip6_null_entry will stay a dst based return for lookups that fail to
match an entry.

Add a new fib6_null_entry which constitutes the root node and leafs
for fibs. Replace existing references to ip6_null_entry with the
new fib6_null_entry when dealing with FIBs.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add expires to rt6_info for FIB entries, and add fib6 helpers to
manage it. Data path use of dst.expires remains.

The transition is fairly straightforward: when working with fib entries,
rt->dst.expires is just rt->expires, rt6_clean_expires is replaced with
fib6_clean_expires, rt6_set_expires becomes fib6_set_expires, and
rt6_check_expired becomes fib6_check_expired, where the fib6 versions
are added by this patch.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similar to IPv4, add fib metrics to the fib struct, which at the moment
is rt6_info. Will be moved to fib6_info in a later patch. Copy metrics
into dst by reference using refcount.

To make the transition:
- add dst_metrics to rt6_info. Default to dst_default_metrics if no
  metrics are passed during route add. No need for a separate pmtu
  entry; it can reference the MTU slot in fib6_metrics

- ip6_convert_metrics allocates memory in the FIB entry and uses
  ip_metrics_convert to copy from netlink attribute to metrics entry

- the convert metrics call is done in ip6_route_info_create simplifying
  the route add path
  + fib6_commit_metrics and fib6_copy_metrics and the temporary
    mx6_config are no longer needed

- add fib6_metric_set helper to change the value of a metric in the
  fib entry since dst_metric_set can no longer be used

- cow_metrics for IPv6 can drop to dst_cow_metrics_generic

- rt6_dst_from_metrics_check is no longer needed

- rt6_fill_node needs the FIB entry and dst as separate arguments to
  keep compatibility with existing output. Current dst address is
  renamed to dest.
  (to be consistent with IPv4 rt6_fill_node really should be split
  into 2 functions similar to fib_dump_info and rt_fill_info)

- rt6_fill_node no longer needs the temporary metrics variable
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Defer setting dst input, output and error until fib entry is copied.

The reject path from ip6_route_info_create is moved to a new function
ip6_rt_init_dst_reject with a helper doing the conversion from fib6_type
to dst error.

The remainder of the new ip6_rt_init_dst is an amalgamtion of dst code
from addrconf_dst_alloc and the non-reject path of ip6_route_info_create.
The dst output function is always ip6_output and the input function is
either ip6_input (local routes), ip6_mc_input (multicast routes) or
ip6_forward (anything else).

A couple of places using dst.error are updated to look at rt6i_flags.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce fib6_nh structure and move nexthop related data from
rt6_info and rt6_info.dst to fib6_nh. References to dev, gateway or
lwtstate from a FIB lookup perspective are converted to use fib6_nh;
datapath references to dst version are left as is.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The RTN_ type for IPv6 FIB entries is currently embedded in rt6i_flags
and dst.error. Since dst is going to be removed, it can no longer be
relied on for FIB dumps so save the route type as fib6_type.

fc_type is set in current users based on the algorithm in rt6_fill_node:
  - rt6i_flags contains RTF_LOCAL: fc_type = RTN_LOCAL
  - rt6i_flags contains RTF_ANYCAST: fc_type = RTN_ANYCAST
  - else fc_type = RTN_UNICAST

Similarly, fib6_type is set in the rt6_info templates based on the
RTF_REJECT section of rt6_fill_node converting dst.error to RTN type.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code move only.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass network namespace reference into route add, delete and get
functions.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass net namespace to fib6_update_sernum. It can not be marked const
as fib6_new_sernum will change ipv6.fib6_sernum.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A later patch removes rt6i_table from rt6_info. Save the ipv6
table for a VRF in net_vrf. fib tables can not be deleted so
no reference counting or locking is required.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to keep expires time for IPv6 routes in a dump of FIB entries.
Update rtnl_put_cacheinfo to allow dst to be NULL in which case
rta_cacheinfo will only contain non-dst data.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move logic of fib_convert_metrics into ip_metrics_convert. This allows
the code that converts netlink attributes into metrics struct to be
re-used in a later patch by IPv6.

This is mostly a code move with the following changes to variable names:
  - fi->fib_net becomes net
  - fc_mx and fc_mx_len are passed as inputs pulled from fib_config
  - metrics array is passed as an input from fi->fib_metrics->metrics
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Send a netlink notification when userspace adds a manually configured
address if DAD is enabled and optimistic flag isn't set.
Moreover send RTM_DELADDR notifications for tentative addresses.

Some userspace applications (e.g. NetworkManager) are interested in
addr netlink events albeit the address is still in tentative state,
however events are not sent if DAD process is not completed.
If the address is added and immediately removed userspace listeners
are not notified. This behaviour can be easily reproduced by using
veth interfaces:

$ ip -b - <<EOF
> link add dev vm1 type veth peer name vm2
> link set dev vm1 up
> link set dev vm2 up
> addr add 2001:db8:a:b:1:2:3:4/64 dev vm1
> addr del 2001:db8:a:b:1:2:3:4/64 dev vm1
EOF

This patch reverts the behaviour introduced by the commit f784ad3d
("ipv6: do not send RTM_DELADDR for tentative addresses")
Suggested-by: NThomas Haller <thaller@redhat.com>
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support to display pause settings
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like tos inherit, ttl inherit should also means inherit the inner protocol's
ttl values, which actually not implemented in vxlan yet.

But we could not treat ttl == 0 as "use the inner TTL", because that would be
used also when the "ttl" option is not specified and that would be a behavior
change, and breaking real use cases.

So add a different attribute IFLA_VXLAN_TTL_INHERIT when "ttl inherit" is
specified with ip cmd.
Reported-by: NJianlin Shi <jishi@redhat.com>
Suggested-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NHangbin Liu <liuhangbin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NCSI driver defines a generic ncsi_channel_filter struct that can be
used to store arbitrarily formatted filters, and several generic methods
of accessing data stored in such a filter.
However in both the driver and as defined in the NCSI specification
there are only two actual filters: VLAN ID filters and MAC address
filters. The splitting of the MAC filter into unicast, multicast, and
mixed is also technically not necessary as these are stored in the same
location in hardware.

To save complexity, particularly in the set up and accessing of these
generic filters, remove them in favour of two specific structs. These
can be acted on directly and do not need several generic helper
functions to use.

This also fixes a memory error found by KASAN on ARM32 (which is not
upstream yet), where response handlers accessing a filter's data field
could write past allocated memory.

[  114.926512] ==================================================================
[  114.933861] BUG: KASAN: slab-out-of-bounds in ncsi_configure_channel+0x4b8/0xc58
[  114.941304] Read of size 2 at addr 94888558 by task kworker/0:2/546
[  114.947593]
[  114.949146] CPU: 0 PID: 546 Comm: kworker/0:2 Not tainted 4.16.0-rc6-00119-ge156398bfcad #13
...
[  115.170233] The buggy address belongs to the object at 94888540
[  115.170233]  which belongs to the cache kmalloc-32 of size 32
[  115.181917] The buggy address is located 24 bytes inside of
[  115.181917]  32-byte region [94888540, 94888560)
[  115.192115] The buggy address belongs to the page:
[  115.196943] page:9eeac100 count:1 mapcount:0 mapping:94888000 index:0x94888fc1
[  115.204200] flags: 0x100(slab)
[  115.207330] raw: 00000100 94888000 94888fc1 0000003f 00000001 9eea2014 9eecaa74 96c003e0
[  115.215444] page dumped because: kasan: bad access detected
[  115.221036]
[  115.222544] Memory state around the buggy address:
[  115.227384]  94888400: fb fb fb fb fc fc fc fc 04 fc fc fc fc fc fc fc
[  115.233959]  94888480: 00 00 00 fc fc fc fc fc 00 04 fc fc fc fc fc fc
[  115.240529] >94888500: 00 00 04 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[  115.247077]                                             ^
[  115.252523]  94888580: 00 04 fc fc fc fc fc fc 06 fc fc fc fc fc fc fc
[  115.259093]  94888600: 00 00 06 fc fc fc fc fc 00 00 04 fc fc fc fc fc
[  115.265639] ==================================================================
Reported-by: NJoel Stanley <joel@jms.id.au>
Signed-off-by: NSamuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding a dns_resolver key whose payload contains a very long option name
resulted in that string being printed in full.  This hit the WARN_ONCE()
in set_precision() during the printk(), because printk() only supports a
precision of up to 32767 bytes:

    precision 1000000 too large
    WARNING: CPU: 0 PID: 752 at lib/vsprintf.c:2189 vsnprintf+0x4bc/0x5b0

Fix it by limiting option strings (combined name + value) to a much more
reasonable 128 bytes.  The exact limit is arbitrary, but currently the
only recognized option is formatted as "dnserror=%lu" which fits well
within this limit.

Also ratelimit the printks.

Reproducer:

    perl -e 'print "#", "A" x 1000000, "\x00"' | keyctl padd dns_resolver desc @s

This bug was found using syzkaller.
Reported-by: NMark Rutland <mark.rutland@arm.com>
Fixes: 4a2d7892 ("DNS: If the DNS server returns an error, allow that to be cached [ver #2]")
Signed-off-by: NEric Biggers <ebiggers@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavide Caratti <dcaratti@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics such as InHdrErrors should be counted on the ingress
netdev rather than on the dev from the dst, which is the egress.
Signed-off-by: NStephen Suryaputra <ssuryaextr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

BPF core gets access to __inet6_bind via ipv6_bpf_stub_impl, so it is
not invoked directly outside of af_inet6.c. Make it static and move
inet6_bind after to avoid forward declaration.
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jesper Dangaard Brouer says:

====================
XDP redirect memory return API

Submitted against net-next, as it contains NIC driver changes.

This patchset works towards supporting different XDP RX-ring memory
allocators.  As this will be needed by the AF_XDP zero-copy mode.

The patchset uses mlx5 as the sample driver, which gets implemented
XDP_REDIRECT RX-mode, but not ndo_xdp_xmit (as this API is subject to
change thought the patchset).

A new struct xdp_frame is introduced (modeled after cpumap xdp_pkt).
And both ndo_xdp_xmit and the new xdp_return_frame end-up using this.

Support for a driver supplied allocator is implemented, and a
refurbished version of page_pool is the first return allocator type
introduced.  This will be a integration point for AF_XDP zero-copy.

The mlx5 driver evolve into using the page_pool, and see a performance
increase (with ndo_xdp_xmit out ixgbe driver) from 6Mpps to 12Mpps.

The patchset stop at 16 patches (one over limit), but more API changes
are planned.  Specifically extending ndo_xdp_xmit and xdp_return_frame
APIs to support bulking.  As this will address some known limits.

V2: Updated according to Tariq's feedback
V3: Updated based on feedback from Jason Wang and Alex Duyck
V4: Updated based on feedback from Tariq and Jason
V5: Fix SPDX license, add Tariq's reviews, improve patch desc for perf test
V6: Updated based on feedback from Eric Dumazet and Alex Duyck
V7: Adapt to i40e that got XDP_REDIRECT support in-between
V8:
 Updated based on feedback kbuild test robot, and adjust for mlx5 changes
 page_pool only compiled into kernel when drivers Kconfig 'select' feature
V9:
 Remove some inline statements, let compiler decide what to inline
 Fix return value in virtio_net driver
 Adjust for mlx5 changes in-between submissions
V10:
 Minor adjust for mlx5 requested by Tariq
 Resubmit against net-next
V11: avoid leaking info stored in frame data on page reuse
====================
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bpf infrastructure and verifier goes to great length to avoid
bpf progs leaking kernel (pointer) info.

For queueing an xdp_buff via XDP_REDIRECT, xdp_frame info stores
kernel info (incl pointers) in top part of frame data (xdp->data_hard_start).
Checks are in place to assure enough headroom is available for this.

This info is not cleared, and if the frame is reused, then a
malicious user could use bpf_xdp_adjust_head helper to move
xdp->data into this area.  Thus, making this area readable.

This is not super critical as XDP progs requires root or
CAP_SYS_ADMIN, which are privileged enough for such info.  An
effort (is underway) towards moving networking bpf hooks to the
lesser privileged mode CAP_NET_ADMIN, where leaking such info
should be avoided.  Thus, this patch to clear the info when
needed.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Changing API ndo_xdp_xmit to take a struct xdp_frame instead of struct
xdp_buff.  This brings xdp_return_frame and ndp_xdp_xmit in sync.

This builds towards changing the API further to become a bulk API,
because xdp_buff is not a queue-able object while xdp_frame is.

V4: Adjust for commit 59655a5b ("tuntap: XDP_TX can use native XDP")
V7: Adjust for commit d9314c47 ("i40e: add support for XDP_REDIRECT")
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>