There are control flow that sh_cmt_set_next() does double
spin-lock. The callers sh_cmt_{start,stop}() already have
lock. But another callers sh_cmt_clock_event_{start,next}()
does not.

Now sh_cmt_set_next() does not lock by itself. All the
callers should hold spin-lock before calling it.

[damm@opensource.se: use __sh_cmt_set_next() to simplify code]
[damm@opensource.se: added stable, suitable for v2.6.35 + v2.6.36]
Cc: stable@kernel.org
Signed-off-by: NTakashi YOSHII <takashi.yoshii.zj@renesas.com>
Signed-off-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  lguest: populate initial_page_table
  lguest: restore boot speed
  lguest: fix crash lguest_time_init

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ryusuke/nilfs2:
  nilfs2: fix regression of garbage collection ioctl

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: define separate EVIOCGKEYCODE_V2/EVIOCSKEYCODE_V2
  Input: wacom - add another Bamboo Pen ID (0xd4)

Two x86 patches broke lguest:
1) v2.6.35-492-g72d7c3b3, which changed x86 to use the memblock allocator.

In lguest, the host places linear page tables at the top of mem, which
used to be enough to get us up to the swapper_pg_dir page tables.  With
the first patch, the direct mapping tables used that memory:

Before: kernel direct mapping tables up to 4000000 @ 7000-1a000
After: kernel direct mapping tables up to 4000000 @ 3fed000-4000000

I initially fixed this by lying about the amount of memory we had, so
the kernel wouldn't blatt the lguest boot pagetables (yuk!), but then...

2) v2.6.36-rc8-54-gb40827fa, which made x86 boot use initial_page_table.

This was initialized in a part of head_32.S which isn't executed by
lguest; it is then copied into swapper_pg_dir.  So we have to initialize
it; and anyway we switch to it before we blatt the old tables, so that
fixes the previous damage as well.

For the moment, I cut & pasted the code into lguest's boot code, but
next merge window I will merge them.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Cc: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
To: x86@kernel.org

lguest is dumb and drops *all* the pagetables for set_pte (which is
only used for kernel mapping manipulation, so it's OK without highmem).

But it's used a lot in boot, too.  As a guest optimization, we
suppressed this flushing until the first page switch.  Now we have
initial_page_table, that happens much earlier, so extend the heuristic
to wait until we switch to something other than the swapper_pg_dir or
initial_page_table.

As measured on my laptop under kvm, this dropped the time-to-mount-root
from 48 seconds to 4.3 seconds.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

fe25c7fc "x86: lguest: Convert to new irq chip functions" converted
enable_lguest_irq() to take a struct irq_data *, but didn't fix the one
internal caller.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
To: x86@kernel.org

On 2.6.37-rc1, garbage collection ioctl of nilfs was broken due to the
commit 263d90ce ("nilfs2: remove own inode hash used for GC"),
and leading to filesystem corruption.

The patch doesn't queue gc-inodes for log writer if they are reused
through the vfs inode cache.  Here, gc-inode is the inode which
buffers blocks to be relocated on GC.  That patch queues gc-inodes in
nilfs_init_gcinode() function, but this function is not called when
they don't have I_NEW flag.  Thus, some of live blocks are wrongly
overrode without being moved to new logs.

This resolves the problem by moving the gc-inode queueing to an outer
function to ensure it's done right.
Signed-off-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ghash-intel - ghash-clmulni-intel_glue needs err.h

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
  ext4: fix typo which broke '..' detection in ext4_find_entry()
  ext4: Turn off multiple page-io submission by default

Without this, gcc 4.5 won't compile xen-netfront and xen-blkfront, where
this is being used to specify array sizes.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Signed-off-by: NJeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: David Miller <davem@davemloft.net>
Cc: Stable Kernel <stable@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The MSM main git tree has changed over to this new address.
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The install_special_mapping routine (used, for example, to setup the
vdso) skips the security check before insert_vm_struct, allowing a local
attacker to bypass the mmap_min_addr security restriction by limiting
the available pages for special mappings.

bprm_mm_init() also skips the check, and although I don't think this can
be used to bypass any restrictions, I don't see any reason not to have
the security check.

  $ uname -m
  x86_64
  $ cat /proc/sys/vm/mmap_min_addr
  65536
  $ cat install_special_mapping.s
  section .bss
      resb BSS_SIZE
  section .text
      global _start
      _start:
          mov     eax, __NR_pause
          int     0x80
  $ nasm -D__NR_pause=29 -DBSS_SIZE=0xfffed000 -f elf -o install_special_mapping.o install_special_mapping.s
  $ ld -m elf_i386 -Ttext=0x10000 -Tbss=0x11000 -o install_special_mapping install_special_mapping.o
  $ ./install_special_mapping &
  [1] 14303
  $ cat /proc/14303/maps
  0000f000-00010000 r-xp 00000000 00:00 0                                  [vdso]
  00010000-00011000 r-xp 00001000 00:19 2453665                            /home/taviso/install_special_mapping
  00011000-ffffe000 rwxp 00000000 00:00 0                                  [stack]

It's worth noting that Red Hat are shipping with mmap_min_addr set to
4096.
Signed-off-by: NTavis Ormandy <taviso@google.com>
Acked-by: NKees Cook <kees@ubuntu.com>
Acked-by: NRobert Swiecki <swiecki@google.com>
[ Changed to not drop the error code - akpm ]
Reviewed-by: NJames Morris <jmorris@namei.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add missing header file:

arch/x86/crypto/ghash-clmulni-intel_glue.c:256: error: implicit declaration of function 'IS_ERR'
arch/x86/crypto/ghash-clmulni-intel_glue.c:257: error: implicit declaration of function 'PTR_ERR'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The desire to keep old names for the EVIOCGKEYCODE/EVIOCSKEYCODE while
extending them to support large scancodes was a mistake. While we tried
to keep ABI intact (and we succeeded in doing that, programs compiled
on older kernels will work on newer ones) there is still a problem with
recompiling existing software with newer kernel headers.

New kernel headers will supply updated ioctl numbers and kernel will
expect that userspace will use struct input_keymap_entry to set and
retrieve keymap data. But since the names of ioctls are still the same
userspace will happily compile even if not adjusted to make use of the
new structure and will start miraculously fail in the field.

To avoid this issue let's revert EVIOCGKEYCODE/EVIOCSKEYCODE definitions
and add EVIOCGKEYCODE_V2/EVIOCSKEYCODE_V2 so that userspace can explicitly
select the style of ioctls it wants to employ.
Reviewed-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NJarod Wilson <jarod@redhat.com>
Acked-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: It is likely that WORKER_NOT_RUNNING is true
  MAINTAINERS: Add workqueue entry
  workqueue: check the allocation of system_unbound_wq

* 'for-linus' of git://neil.brown.name/md:
  md: protect against NULL reference when waiting to start a raid10.
  md: fix bug with re-adding of partially recovered device.
  md: fix possible deadlock in handling flush requests.
  md: move code in to submit_flushes.
  md: remove handling of flush_pending in md_submit_flush_data

There is a possibility that the last word of a transaction will be lost
if data is not ready.  Re-read in poll_transfer() to solve this issue
when poll_mode is enabled.

Verified on SPI touch screen device.
Signed-off-by: NMajor Lee <major_lee@wistron.com>
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This gets caught by the new sanity check code. Instead of the slash use a
different symbol. This was originally found by Major Lee who proposed a
rather more complex patch which changed the name according to the chip
type.

On the basis that we are in a late -rc and making Linus grumpy isn't always
a good idea (however fun) this is a simple alternative.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

There should be a check for the NUL character instead of '0'.

Fortunately the only thing that cares about this is NFS serving, which
is why we didn't notice this in the merge window testing.
Reported-by: NPhil Carmody <ext-phil.2.carmody@nokia.com>
Signed-off-by: NAaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: N"Theodore Ts'o" <tytso@mit.edu>

* 'sh-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: wire up accept4 syscall (non-multiplexed path)
  sh: Enable deprecated IRQ chip APIs for MFD and GPIOLIB drivers.

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP2: PRCM: fix some SHIFT macros that were actually bitmasks
  OMAP2+: PM/serial: fix console semaphore acquire during suspend
  OMAP1: SRAM: fix size for OMAP1611 SoCs
  arm: omap2: io: fix clk_get() error check
  arm: plat-omap: counter_32k: use IS_ERR() instead of NULL check
  omap: nand: remove hardware ECC as default
  omap: zoom: wl1271 slot is MMC_CAP_POWER_OFF_CARD
  omap: PM debug: fix wake-on-timer debugfs dependency

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: 6535/1: V6 MPCore v6_dma_inv_range and v6_dma_flush_range RWFO fix
  ARM: 6534/1: Make CONFIG_FPE_NWFPE depend on !CONFIG_THUMB2_KERNEL
  ARM: 6533/1: Thumb-2: Make CONFIG_THUMB2_KERNEL depend on !CPU_V6
  Change bcmring Maintainer list.
  ARM: Update mach-types
  ARM: 6528/1: Use CTR for the I-cache line size on ARMv7
  ARM: 6527/1: Use CTR instead of CCSIDR for the D-cache line size on ARMv7
  ARM: pxa/palm: fix ifdef around gen_nand driver registration
  ARM: pxa: fix pxa2xx-flash section mismatch
  ARM: mmp2: remove not used clk_rtc

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
  sparc: Write to prom console using indirect buffer.
  sparc: Delete prom_*getchar().
  sparc: Pass buffer pointer all the way down to prom_{get,put}char().
  sparc: Do not export prom_nb{get,put}char().
  sparc64: Delete prom_setcallback().
  sparc64: Unexport prom_service_exists().
  sparc: Kill prom devops_{32,64}.c
  sparc: Remove prom_pathtoinode()
  sparc64: Delete prom_puts() unused.
  SPARC/LEON: removed constant timer initialization as if HZ=100, now it reflects the value of HZ

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits)
  pppoe.c: Fix kernel panic caused by __pppoe_xmit
  WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers.
  bnx2x: Advance a version number to 1.60.01-0
  bnx2x: Fixed a compilation warning
  bnx2x: LSO code was broken on BE platforms
  qlge: Fix deadlock when cancelling worker.
  net: fix skb_defer_rx_timestamp()
  cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes
  phy: add the IC+ IP1001 driver
  atm: correct sysfs 'device' link creation and parent relationships
  MAINTAINERS: remove me from tulip
  SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address
  enic: Bug Fix: Pass napi reference to the isr that services receive queue
  ipv6: fix nl group when advertising a new link
  connector: add module alias
  net: Document the kernel_recvmsg() function
  r8169: Fix runtime power management
  hso: IP checksuming doesn't work on GE0301 option cards
  xfrm: Fix xfrm_state_migrate leak
  net: Convert netpoll blocking api in bonding driver to be a counter
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
  [SCSI] hpsa: fix redefinition of PCI_DEVICE_ID_CISSF
  [SCSI] qla2xxx: Update version number to 8.03.05-k0.
  [SCSI] qla2xxx: Properly set the return value in qla2xxx_eh_abort function.
  [SCSI] qla2xxx: Correct issue where NPIV-config data was not being allocated for 82xx parts.
  [SCSI] qla2xxx: Change MSI initialization from using incorrect request_irq parameter.
  [SCSI] qla2xxx: Populate Command Type 6 LUN field properly.
  [SCSI] zfcp: Issue FCP command without holding SCSI host_lock
  [SCSI] zfcp: Prevent usage w/o holding a reference
  [SCSI] zfcp: No ERP escalation on gpn_ft eval
  [SCSI] zfcp: Correct false abort data assignment.
  [SCSI] zfcp: Fix common FCP request reception
  [SCSI] Eliminate error handler overload of the SCSI serial number
  [SCSI] pmcraid: disable msix and expand device config entry
  [SCSI] bsg: correct fault if queue object removed while dev_t open
  [SCSI] osd: checking NULL instead of ERR_PTR()

* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
  kgdboc,input: Fix regression with keyboard release key and early debugging

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
  ACPI / PM: Do not save/restore NVS on Sony Vaio VGN-NW130D
  ACPI/HEST: adjust section selection
  ACPI: eliminate unused variable warning for !ACPI_SLEEP
  ACPI/PNP: avoid section mismatch warning
  ACPI thermal: remove two unused functions
  ACPI: fix a section mismatch
  ACPI, APEI, use raw spinlock in ERST
  ACPI: video: fix build for CONFIG_ACPI=n
  ACPI: video: fix build for VIDEO_OUTPUT_CONTROL=n
  ACPI: fix allowing to add/remove multiple _OSI strings
  acpi: fix _OSI string setup regression
  ACPI: EC: Add another dmi match entry for MSI hardware
  ACPI battery: update status upon sysfs query
  ACPI ac: update AC status upon sysfs query
  ACPI / PM: Do not refcount power resources that can't be turned on
  ACPI / PM: Check device state before refcounting power resources

* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
  intel_idle: recognize ARAT on WSM-EX

Cache ownership must be acquired by reading/writing data from the
cache line to make cache operation have the desired effect on the
SMP MPCore CPU. However, the ownership is never acquired in the
v6_dma_inv_range function when cleaning the first line and
flushing the last one, in case the address is not aligned
to D_CACHE_LINE_SIZE boundary.
Fix this by reading/writing data if needed, before performing
cache operations.
While at it, fix v6_dma_flush_range to prevent RWFO outside
the buffer.

Cc: stable@kernel.org
Signed-off-by: NValentine Barshak <vbarshak@mvista.com>
Signed-off-by: NGeorge G. Davis <gdavis@mvista.com>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Because the nwfpe support is unlikely to be used on new platforms
and requires CONFIG_OABI_COMPAT, which is not generally used with
ARMv7+, we shouldn't expect to build nwfpe support into a Thumb-2
kernel.

At present, nwfpe contains assembly code which isn't Thumb-2
compatible, and for now it doesn't appear useful to port this
code.

All ARMv7-A/R platforms necessarily have VFPv3 hardware floating-
point natively, making emulation unnecessary.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes sense, because Thumb-2 code can't execute on plain
ARMv6 processors.

This will avoid accidentally configuring a broken kernel where the
config otherwise would allow multiple architecture versions to
coexist in the same kernel.

Not adding !CPU_V5 etc., because the chance of anyone trying to
put v5 and v7 in the same kernel is low, and I'm not aware of
any mach which can do this.  These could be added later if it
matters.

Note that the rules may need to be refined if support for the
ARM1156J(F)-S processor is later added to the kernel, since this
processor supports the rare ARMv6T2 extensions, which add support
for Thumb-2 and a few other ARMv7 features.
Signed-off-by: NDave Martin <dave.martin@linaro.org>
Acked-by: NCatalin Marinas <catalin.marinas@arm.com>
Acked-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

I am Jiandong Zheng working on BCMRING in Broadcom Canada Ltd. I am
replacing Leo Chen (leochen@broadcom.com) as "ARM/BCMRING ARM
ARCHITECTURE" and "ARM/BCMRING MTD NAND DRIVER" maintainer from
Broadcom as he is no longer the maintainer of these components.
Signed-off-by: NJiandong Zheng <jdzheng@broadcom.com>
Acked-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Merge branch 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6

* 'fbdev-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/fbdev-2.6:
  fbdev: Fix fb_find_nearest_mode refresh comparison

* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging:
  hwmon: (ltc4215) make sysfs file match the alarm cause

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: at_hdmac: fix buffer transfer size specification
  fsldma: fix issue of slow dma
  dmaengine i.MX SDMA: initialize on module_init
  dma : EG20T PCH: Fix miss-setting DMA descriptor
  intel_mid_dma: fix section mismatch warnings
  dmaengine: imx-sdma: fix bug in buffer descriptor initialization
  drivers/dma/ppc4xx: Use printf extension %pR for struct resource
  drivers/dma/ioat: Use the ccflag-y instead of EXTRA_CFLAGS
  drivers/dma/: Use the ccflag-y instead of EXTRA_CFLAGS
  dma: intel_mid_dma: fix double free on mid_setup_dma error path
  dma: imx-dma: fix imxdma_probe error path

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  IB/uverbs: Handle large number of entries in poll CQ

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6:
  firewire: ohci: fix regression with Agere FW643 rev 06, disable MSI
  firewire: ohci: fix regression with VIA VT6315, disable MSI

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
  regulator: tps6586x: correct register table
  regulator: tps6586x: Handle both enable reg/bits being the same
  regulator: tps6586x: Fix TPS6586X_DVM to store goreg/bit
  regulator: tps6586x: Add missing bit mask generation