As firmware starting from 3.2.0.12 has some API changes and doesn't work
with older versions of ath6kl we need to bump up the API version. This
way we don't break anything.

Also store which version of API is used and print that during boot:

ath6kl: ar6003 hw 2.1.1 sdio fw 3.2.0.13 api 3
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently ath6kl has just hardcoded paths to each firmware file. Change
this more dynamic by separating the the directory and file name from each
other. That way it's easier to dynamically create full paths to firmware and
code looks better. And now it's possible to remove a function needed by
devicetree code.

While at it add a structure inside struct ath6kl_hw to contain all
firmware names. I deliberately omitted board file support as
those will be handled later.

This is needed for firmware API 3.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware ARP module requires own IP addr in order to respond
to the outside world when the target is in WOW suspend state.

At present, firmware ARP module has capability to hold 2 IP addr.
So, WOW mode will be disabled if the total IP addr configured in
net_dev for our device is greater than firmware limit (MAX_IP_ADDRS)
which is 2 at this moment.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In this way, caller is free to pass only the value of IP addr
to configure.

In addition to this,
  * 'ips' variable data type in struct wmi_set_ip_cmd is changed
     from __le32 to __be32 in order to match network byte order.
  *  ipv4_is_multicast() is used to validate multicast ip addr.
  *  New argument if_idx is added to supply correct vif index
     to ath6kl_wmi_cmd_send().

This will be used in the next patch.
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NThirumalai Pachamuthu <tpachamu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Empty IE buffer means that the new association is not supposed to
include extra IEs. Make sure any previously configured (Re)Association
Request frame IEs get cleared in such a case. This is based on a patch
from Shuibing.

Cc: Dai Shuibing <shuibing@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to avoid the scenario where the bss entry of the AP got
expired when reporting roaming event to current AP. As the bss
entry for the current bss is available in driver, pass this bss
to cfg80211. This fixes WARNING: at net/wireless/sme.c:586.

This patch depends on the following patch in cfg80211
"cfg80211: Fix race in bss timeout".
Reported-by: NKalle Valo <kvalo@qca.qualcomm.com>
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix a few minor issues with wmediumd_pid:
a) make static
b) use u32 to match the snd_pid type
c) use ACCESS_ONCE since we don't lock it
d) don't explicitly initialize to 0
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

its not used anywhere in the current code
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

before concluding that the recieved beacon is for us, let us make sure
that the BSSID is non-zero. when I configured ad-hoc mode as creator and
left it for some time without joining I found we recieved few frames whose
BSSID is zero, which we concluded wrongly as 'my_beacons'
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reported-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Negate has higher precendence than compare and since neither zero nor
one are equal to four or eight the original condition is always false.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This initial DFS module provides basic functionality to deal
with radar pulses reported by the Atheros DFS HW pulse detector.

The reported data is evaluated and basic plausibility checks
are performed to filter false pulses. Passing radar pulses are
forwarded to pattern detectors which are not yet implemented.

(Some modifications to actually use ATH9K_DFS_DEBUGFS based on comments
from Julian Calaby <julian.calaby@gmail.com>. -- JWL)
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In order to enable DFS upstream we want to be sure
DFS has been tested for each chipset. Push for public
documentation of the requirements we want in place and
allow for enabling each chipset through a single upstream
commit.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This can later be used by other drivers that implement
DFS support.
Signed-off-by: NZefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In ai_attach(), space is allocated for an si_info struct. Immediately
after the allocation, routine ai_doattach() is called and that allocated
space is set to zero. As no other routine calls ai_doattach(), kzalloc()
can be utilized.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

A debug level was added to the ath module for printing
MCI messages but no documentation was provided. Clarify that
MCI is the Message Coexistence Interface, a private protocol
used exclusively for WLAN-BT coexistence starting from
AR9462.

Cc: wtsao@qca.qualcomm.com
Cc: rmanohar@qca.qualcomm.com
Cc: mohammed@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: NLuis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The receiver will discard them anyway.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of releasing and taking back the lock over and over again in the
tx path, hold the lock a bit longer, requiring much fewer lock/unlock pairs.
This makes locking much easier to review and should not have any noticeable
performance/latency impact.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

tid->seq_next is initialized on A-MPDU start anyway, and the comment next
to this chunk of code seems to be bogus as well.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When processing A-MPDU tx status, only send a BAR for the failed packet
with the highest sequence number.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of limiting a subframe to 10 A-MPDU software transmission attempts,
count hardware retransmissions as well and raise the limit a bit. That way
there will be fewer software retransmission attempts when traffic suffers
from lots of hardware retransmissions.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When compiling wl12xx for x86, there was a warning complaining about
the size of the buffer we were allocating in the stack:

drivers/net/wireless/wl12xx/debugfs.c: In function 'driver_state_read':
drivers/net/wireless/wl12xx/debugfs.c:380:1: warning: the frame size of 1040 bytes is larger than 1024 bytes

To prevent this, allocate the buffer in the heap instead.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

wl1271_configure_suspend_sta leaves a stale stack declared
completion in wlvif->ps_compl. Set it to NULL before returning.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
[small fix to use wlvif->ps_compl instead of wl->ps_compl]
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We don't use WL12XX_BA_SUPPORT_FW_COST_VER2_START nor
WL12XX_BA_SUPPORT_FW_COST_VER2_END anymore.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

The ACX_PD_THRESHOLD configuration command is deprecated and should
not be used anymore.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Use the newly introduced ieee80211_free_txskb() instead
of dev_kfree_skb() for failed tx packets.

Additionally, if the skb is a dummy packet, re-enqueue
it (as the fw expects it) instead of freeing it.
Reported-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We need to set the extended radio parameters for wl127x only.
Currently, we were only calling this command with wl127x STA mode, but
we should also do it for AP mode.

Move the call to the extended radio paramaters to the common hw_init
and use a single if for the chip type to do everything at once.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

We should not get an hlid value bigger than WL12XX_MAX_LINKS from
wl1271_rx_handle_data().  We have a WARN_ON in case it happens.  But
despite the warning, we would still go ahead and write the hlid bit
into active_hlids (a stack variable).  This would cause us to
overwrite other data in the stack.

To avoid this problem, we now skip the write when issuing the warning,
so at least we don't corrupt data.
Signed-off-by: NLuciano Coelho <coelho@ti.com>

Commit 80900d01 accidently broke
the ABI for testmode commands. Restore the ABI again.
Signed-off-by: NPontus Fuchs <pontus.fuchs@gmail.com>
Cc: stable@kernel.org
Signed-off-by: NLuciano Coelho <coelho@ti.com>

ieee80211_free_txskb should be used when dropping a frame in the device
rx path such that mac80211 knows about this frame being dropped.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg_workqueue was added to notify cfg80211 that scan, connect
or disconnect is done by calling respective completion handlers.
We can avoid use of this workqueue by calling those handlers
from other places.
1) Call connect, disconnect completion handlers in their callback
   functions.
   ex. Call cfg80211_connect_result() in mwifiex_cfg80211_connect()
2) Call scan completion handler after parsing response of last scan
   command in a queue.

After removing the workqueue, variables (assoc_request etc.) and
checks used for mutual exclusion become redundant. Those are also
removed in this patch.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NNishant Sarmukadam <nishants@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My previous patch
34a5b4b6 iwlwifi: do not re-configure
HT40 after associated

Fix the case of HT40 after association on specified AP, but it break the
association for some APs and cause not able to establish connection.
We need to address HT40 before and after addociation.

CC: stable@vger.kernel.org #3.0+
Reported-by: NAndrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: NAndrej Gelenberg <andrej.gelenberg@udo.edu>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Ted reported that he couldn't connect to some APs
and bisected it to the tx_sync implementation.
Disable it for the BSS context to fix this issue.
Reported-by: NTed Ts'o <tytso@mit.edu>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Command cancel path cancels the current command and moves
it to free command queue. While doing that it deletes the
command entry from the pending list. This is not correct
as the entry has been already deleted from the pending
list at 'mwifiex_exec_next_cmd'. Fixing it.

Also making sure the stale command pointer is cleaned and
unaccessible for later use.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables support for doing P2P management operations like device
discovery on top of a station interface. After group formation, the station
interface will become a P2P GO/client interface as the case may be.

This feature requires modifications to a couple of existing WMI structures and
therefore new command ids and structures have been defined in order to be
compatible with older firmware versions and other chips. The exception here is
the wmi_connect_cmd. Adding a new field to the end of the structure will not
cause any issues with previous firmware versions since firmware only checks for
minimum length of the command. The other structures are of variable length,
hence it was not possible to add new fields to the end.

The new command ids have to be added to the end of enum wmi_cmd_id, so it has
updated to match the firmware.

The driver will support both the 'old' and the 'new' commands for a while by
checking the firmware capabilities.
Signed-off-by: NAarthi Thiruvengadam <athiruve@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

AR6003 family use uart_tx=8 and refclk=26Mhz by default, and AR6004 family
uses different uart_tx pin and could also support various xtal source,
moves these per hw configuration.
Signed-off-by: NRyan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Avoids this:

ERROR: "bcma_chipco_pll_write" [drivers/net/wireless/b43/b43.ko] undefined!
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

mwifiex driver no longer supports it's own custom regulatory rules,
but custom regulatory domain capability is still advertised during
wiphy registration by the driver.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>