Similar to the ancient commit a5fe8e76 ("regulatory: add NUL
to alpha2"), add another byte to alpha2 in the request struct so
that when we use nla_put_string(), we don't overrun anything.

Fixes: 73d54c9e ("cfg80211: add regulatory netlink multicast group")
Reported-by: NKees Cook <keescook@google.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case an ADDBA request is received while there is already
an ongoing BA sessions with the same parameters, i.e., update
flow, an ADBBA response with decline status was sent twice. Fix it.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some APs include a non global operating class in their extended channel
switch information element. In such a case, as the operating class is not
known, mac80211 would decide to disconnect.

However the specification states that the operating class needs to be
taken from Annex E, but it does not specify from which table it should be
taken, so it is valid for an AP to use a non global operating class.

To avoid possibly unneeded disconnection, in such a case ignore the
operating class and assume that the current band is used, and if the
resulting channel and band configuration is invalid disconnect.
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a low level driver calls cfg80211_disconnected(), wep keys are
not cleared. As a result, following connection requests will fail
since cfg80211 internal state shows a connection is still in progress.

Fix this by clearing the wep keys when disconnecting.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

sta_info_alloc can be called from atomic paths (such as RX path)
so we need to call pcpu_alloc with the correct gfp.

Fixes: c9c5962b ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If sta_info_alloc fails after allocating the per CPU statistics,
they are not properly freed.

Fixes: c9c5962b ("mac80211: enable collecting station statistics per-CPU")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This ensures that mac80211 allocated management frames are properly
aligned, which makes copying them more efficient.
For instance, mt76 uses iowrite32_copy to copy beacon frames to beacon
template memory on the chip.
Misaligned 32-bit accesses cause CPU exceptions on MIPS and should be
avoided.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We're obviously not part of a memory reclaim path, so don't set the flag.

This also causes a warning in check_flush_dependency() since we end up
in a code path that flushes a non-reclaim workqueue, and we shouldn't do
that if we were really part of reclaim.

Reported-by: syzbot+41cdaf4232c50e658934@syzkaller.appspotmail.com
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

gcc-8 warns about some obviously incorrect code:

net/mac80211/cfg.c: In function 'cfg80211_beacon_dup':
net/mac80211/cfg.c:2896:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]

From the context, I conclude that we want to copy from beacon into
new_beacon, as we do in the rest of the function.

Cc: stable@vger.kernel.org
Fixes: 73da7d5b ("mac80211: add channel switch command and beacon callbacks")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

mesh TTL offset in Mesh Channel Switch Parameters element depends on
not only Secondary Channel Offset element, but also affected by
HT Control field and Wide Bandwidth Channel Switch element.
So use element structure to manipulate mesh channel swich param IE
after removing its constant attribution to correct the miscalculation.
Signed-off-by: NPeter Oh <peter.oh@bowerswilkins.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Mesh used to use the mandatory rates as basic rates, but we got
the calculation of mandatory rates wrong until some time ago.
Fix this this broke interoperability with older versions since
now more basic rates are required, and thus the MBSS isn't the
same and the network stops working.

Fix this by simply using only 1Mbps as the basic rate in 2.4GHz.
Since the changed mandatory rates only affected 2.4GHz, this is
all we need to make it work again.
Reported-and-tested-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Fixes: 1bd773c0 ("wireless: set correct mandatory rate flags")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Pull networking fixes from David Miller:

 1) The per-network-namespace loopback device, and thus its namespace,
    can have its teardown deferred for a long time if a kernel created
    TCP socket closes and the namespace is exiting meanwhile. The kernel
    keeps trying to finish the close sequence until it times out (which
    takes quite some time).

    Fix this by forcing the socket closed in this situation, from Dan
    Streetman.

 2) Fix regression where we're trying to invoke the update_pmtu method
    on route types (in this case metadata tunnel routes) that don't
    implement the dst_ops method. Fix from Nicolas Dichtel.

 3) Fix long standing memory corruption issues in r8169 driver by
    performing the chip statistics DMA programming more correctly. From
    Francois Romieu.

 4) Handle local broadcast sends over VRF routes properly, from David
    Ahern.

 5) Don't refire the DCCP CCID2 timer endlessly, otherwise the socket
    can never be released. From Alexey Kodanev.

 6) Set poll flags properly in VSOCK protocol layer, from Stefan
    Hajnoczi.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  VSOCK: set POLLOUT | POLLWRNORM for TCP_CLOSING
  dccp: don't restart ccid2_hc_tx_rto_expire() if sk in closed state
  net: vrf: Add support for sends to local broadcast address
  r8169: fix memory corruption on retrieval of hardware statistics.
  net: don't call update_pmtu unconditionally
  net: tcp: close sock if net namespace is exiting

Pull drm fixes from Dave Airlie:
 "A fairly urgent nouveau regression fix for broken irqs across
  suspend/resume came in. This was broken before but a patch in 4.15 has
  made it much more obviously broken and now s/r fails a lot more often.

  The fix removes freeing the irq across s/r which never should have
  been done anyways.

  Also two vc4 fixes for a NULL deference and some misrendering /
  flickering on screen"

* tag 'drm-fixes-for-v4.15-rc10-2' of git://people.freedesktop.org/~airlied/linux:
  drm/nouveau: Move irq setup/teardown to pci ctor/dtor
  drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
  drm/vc4: Flush the caches before the bin jobs, as well.

select(2) with wfds but no rfds must return when the socket is shut down
by the peer.  This way userspace notices socket activity and gets -EPIPE
from the next write(2).

Currently select(2) does not return for virtio-vsock when a SEND+RCV
shutdown packet is received.  This is because vsock_poll() only sets
POLLOUT | POLLWRNORM for TCP_CLOSE, not the TCP_CLOSING state that the
socket is in when the shutdown is received.
Signed-off-by: NStefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ccid2_hc_tx_rto_expire() timer callback always restarts the timer
again and can run indefinitely (unless it is stopped outside), and after
commit 120e9dab ("dccp: defer ccid_hc_tx_delete() at dismantle time"),
which moved ccid_hc_tx_delete() (also includes sk_stop_timer()) from
dccp_destroy_sock() to sk_destruct(), this started to happen quite often.
The timer prevents releasing the socket, as a result, sk_destruct() won't
be called.

Found with LTP/dccp_ipsec tests running on the bonding device,
which later couldn't be unloaded after the tests were completed:

  unregister_netdevice: waiting for bond0 to become free. Usage count = 148

Fixes: 2a91aa39 ("[DCCP] CCID2: Initial CCID2 (TCP-Like) implementation")
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Single irq regression fix
* 'linux-4.15' of git://github.com/skeggsb/linux:
  drm/nouveau: Move irq setup/teardown to pci ctor/dtor

Sukumar reported that sends to the local broadcast address
(255.255.255.255) are broken. Check for the address in vrf driver
and do not redirect to the VRF device - similar to multicast
packets.

With this change sockets can use SO_BINDTODEVICE to specify an
egress interface and receive responses. Note: the egress interface
can not be a VRF device but needs to be the enslaved device.

https://bugzilla.kernel.org/show_bug.cgi?id=198521Reported-by: NSukumar Gopalakrishnan <sukumarg1973@gmail.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hardware statistics retrieval hurts in tight invocation loops.

Avoid extraneous write and enforce strict ordering of writes targeted to
the tally counters dump area address registers.
Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Tested-by: NOliver Freyermuth <o.freyermuth@googlemail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull input fixes from Dmitry Torokhov:
 "The main item is that we try to better handle the newer trackpoints on
  Lenovo devices that are now being produced by Elan/ALPS/NXP and only
  implement a small subset of the original IBM trackpoint controls"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Revert "Input: synaptics_rmi4 - use devm_device_add_group() for attributes in F01"
  Input: trackpoint - only expose supported controls for Elan, ALPS and NXP
  Input: trackpoint - force 3 buttons if 0 button is reported
  Input: xpad - add support for PDP Xbox One controllers
  Input: stmfts,s6sy671 - add SPDX identifier

After do_readv_writev, the inode cache is invalidated anyway, so i_size
will never be read.  It will be fetched from the server which will also
know about updates from other machines.

Fixes deadlock on 32-bit SMP.

See https://marc.info/?l=linux-fsdevel&m=151268557427760&w=2Signed-off-by: NMartin Brandenburg <martin@omnibond.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Mike Marshall <hubcap@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For a while we've been having issues with seemingly random interrupts
coming from nvidia cards when resuming them. Originally the fix for this
was thought to be just re-arming the MSI interrupt registers right after
re-allocating our IRQs, however it seems a lot of what we do is both
wrong and not even nessecary.

This was made apparent by what appeared to be a regression in the
mainline kernel that started introducing suspend/resume issues for
nouveau:

        a0c9259d (irq/matrix: Spread interrupts on allocation)

After this commit was introduced, we started getting interrupts from the
GPU before we actually re-allocated our own IRQ (see references below)
and assigned the IRQ handler. Investigating this turned out that the
problem was not with the commit, but the fact that nouveau even
free/allocates it's irqs before and after suspend/resume.

For starters: drivers in the linux kernel haven't had to handle
freeing/re-allocating their IRQs during suspend/resume cycles for quite
a while now. Nouveau seems to be one of the few drivers left that still
does this, despite the fact there's no reason we actually need to since
disabling interrupts from the device side should be enough, as the
kernel is already smart enough to know to disable host-side interrupts
for us before going into suspend. Since we were tearing down our IRQs by
hand however, that means there was a short period during resume where
interrupts could be received before we re-allocated our IRQ which would
lead to us getting an unhandled IRQ. Since we never handle said IRQ and
re-arm the interrupt registers, this would cause us to miss all of the
interrupts from the GPU and cause our init process to start timing out
on anything requiring interrupts.

So, since this whole setup/teardown every suspend/resume cycle is
useless anyway, move irq setup/teardown into the pci subdev's ctor/dtor
functions instead so they're only called at driver load and driver
unload. This should fix most of the issues with pending interrupts on
resume, along with getting suspend/resume for nouveau to work again.

As well, this probably means we can also just remove the msi rearm call
inside nvkm_pci_init(). But since our main focus here is to fix
suspend/resume before 4.15, we'll save that for a later patch.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: stable@vger.kernel.org
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Some dst_ops (e.g. md_dst_ops)) doesn't set this handler. It may result to:
"BUG: unable to handle kernel NULL pointer dereference at           (null)"

Let's add a helper to check if update_pmtu is available before calling it.

Fixes: 52a589d5 ("geneve: update skb dst pmtu on tx path")
Fixes: a93bf0ff ("vxlan: update skb dst pmtu on tx path")
CC: Roman Kapl <code@rkapl.cz>
CC: Xin Long <lucien.xin@gmail.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull KVM fixes from Radim Krčmář:
 "Fix races and a potential use after free in the s390 cmma migration
  code"

* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: s390: add proper locking for CMMA migration bitmap

Pull btrfs fix from David Sterba:
 "It's been reported recently that readdir can list stale entries under
  some conditions. Fix it."

* tag 'for-4.15-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
  Btrfs: fix stale entries in readdir

When a tcp socket is closed, if it detects that its net namespace is
exiting, close immediately and do not wait for FIN sequence.

For normal sockets, a reference is taken to their net namespace, so it will
never exit while the socket is open.  However, kernel sockets do not take a
reference to their net namespace, so it may begin exiting while the kernel
socket is still open.  In this case if the kernel socket is a tcp socket,
it will stay open trying to complete its close sequence.  The sock's dst(s)
hold a reference to their interface, which are all transferred to the
namespace's loopback interface when the real interfaces are taken down.
When the namespace tries to take down its loopback interface, it hangs
waiting for all references to the loopback interface to release, which
results in messages like:

unregister_netdevice: waiting for lo to become free. Usage count = 1

These messages continue until the socket finally times out and closes.
Since the net namespace cleanup holds the net_mutex while calling its
registered pernet callbacks, any new net namespace initialization is
blocked until the current net namespace finishes exiting.

After this change, the tcp socket notices the exiting net namespace, and
closes immediately, releasing its dst(s) and their reference to the
loopback interface, which lets the net namespace continue exiting.

Link: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1711407
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=97811Signed-off-by: NDan Streetman <ddstreet@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two vc4 fixes that were applied in the last day.
One fixes a NULL dereference, and the other fixes
a flickering bug.

Cc: Eric Anholt <eric@anholt.net>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>

* tag 'drm-misc-fixes-2018-01-24' of git://anongit.freedesktop.org/drm/drm-misc:
  drm/vc4: Fix NULL pointer dereference in vc4_save_hang_state()
  drm/vc4: Flush the caches before the bin jobs, as well.

Pull networking fixes from David Miller:

 1) Avoid negative netdev refcount in error flow of xfrm state add, from
    Aviad Yehezkel.

 2) Fix tcpdump decoding of IPSEC decap'd frames by filling in the
    ethernet header protocol field in xfrm{4,6}_mode_tunnel_input().
    From Yossi Kuperman.

 3) Fix a syzbot triggered skb_under_panic in pppoe having to do with
    failing to allocate an appropriate amount of headroom. From
    Guillaume Nault.

 4) Fix memory leak in vmxnet3 driver, from Neil Horman.

 5) Cure out-of-bounds packet memory access in em_nbyte EMATCH module,
    from Wolfgang Bumiller.

 6) Restrict what kinds of sockets can be bound to the KCM multiplexer
    and also disallow when another layer has attached to the socket and
    made use of sk_user_data. From Tom Herbert.

 7) Fix use before init of IOTLB in vhost code, from Jason Wang.

 8) Correct STACR register write bit definition in IBM emac driver, from
    Ivan Mikhaylov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  net/ibm/emac: wrong bit is used for STA control register write
  net/ibm/emac: add 8192 rx/tx fifo size
  vhost: do not try to access device IOTLB when not initialized
  vhost: use mutex_lock_nested() in vhost_dev_lock_vqs()
  i40e: flower: check if TC offload is enabled on a netdev
  qed: Free reserved MR tid
  qed: Remove reserveration of dpi for kernel
  kcm: Check if sk_user_data already set in kcm_attach
  kcm: Only allow TCP sockets to be attached to a KCM mux
  net: sched: fix TCF_LAYER_LINK case in tcf_get_base_ptr
  net: sched: em_nbyte: don't add the data offset twice
  mlxsw: spectrum_router: Don't log an error on missing neighbor
  vmxnet3: repair memory leak
  ipv6: Fix getsockopt() for sockets with default IPV6_AUTOFLOWLABEL
  pppoe: take ->needed_headroom of lower device into account on xmit
  xfrm: fix boolean assignment in xfrm_get_type_offload
  xfrm: Fix eth_hdr(skb)->h_proto to reflect inner IP version
  xfrm: fix error flow in case of add state fails
  xfrm: Add SA to hardware at the end of xfrm_state_construct()

Pull sparc bugfix from David Miller:
 "Sparc Makefile typo fix"

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
  sparc64: fix typo in CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the sysfs attribute hangs off the RMI bus, which doesn't go away during
firmware flash, it needs to be explicitly removed, otherwise we would try and
register the same attribute twice.

This reverts commit 36a44af5.
Signed-off-by: NNick Dyer <nick@shmanahar.org>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>

The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the typo CONFIG_CRYPTO_DES_SPARC64 => CONFIG_CRYPTO_CAMELLIA_SPARC64

Fixes: 81658ad0 ("sparc64: Add CAMELLIA driver making use of the new camellia opcodes.")
Signed-off-by: NCorentin Labbe <clabbe@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed: rdma bug fixes

This patch contains two small bug fixes related to RDMA.
Both related to resource reservations.
====================
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
kcm: fix two syzcaller issues

In this patch set:

- Don't allow attaching non-TCP or listener sockets to a KCM mux.
- In kcm_attach Check if sk_user_data is already set. This is
  under lock to avoid race conditions. More work is need to make
  all of the users of sk_user_data to use the same locking.

- v2
  Remove unncessary check for not PF_KCM in kcm_attach (suggested by
  Guillaume Nault)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.

Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: NTom Herbert <tom@quantonium.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>