Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.

Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.

Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.

Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rename the 'change_mtu' app callback to 'check_mtu'. This is called
whenever an MTU change is requested on a netdev. It can reject the
change but is not responsible for implementing it.

Introduce a new 'repr_change_mtu' app callback that is hit when the MTU
of a repr is to be changed. This is responsible for performing the MTU
change and verifying it.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide a pointer to the SFP bus in struct net_device, so that the
ethtool module EEPROM methods can access the SFP directly, rather
than needing every user to provide a hook for it.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for having DSA transition entirely to PHYLINK, we need to pass a
PHY interface type to the mac_link_{up,down} callbacks because we may have to
make decisions on that (e.g: turn on/off RGMII interfaces etc.). We do not pass
an entire phylink_link_state because not all parameters (pause, duplex etc.) are
defined when the link is down, only link and interface are.

Update mvneta accordingly since it currently implements phylink_mac_ops.
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were a number of issues with setting the RX coalescing parameters:

- we would not be preserving values that would have been configured
  across close/open calls, instead we would always reset to no timeout
  and 1 interrupt per packet, this would also prevent DIM from setting its
  default usec/pkts values

- when adaptive RX would be turned on, we woud not be fetching the
  default parameters, we would stay with no timeout/1 packet per interrupt
  until the estimator kicks in and changes that

- finally disabling adaptive RX coalescing while providing parameters
  would not be honored, and we would stay with whatever DIM had previously
  determined instead of the user requested parameters

Fixes: 9f4ca058 ("net: bcmgenet: Add support for adaptive RX coalescing")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There were a number of issues with setting the RX coalescing parameters:

- we would not be preserving values that would have been configured
  across close/open calls, instead we would always reset to no timeout
  and 1 interrupt per packet, this would also prevent DIM from setting its
  default usec/pkts values

- when adaptive RX would be turned on, we woud not be fetching the
  default parameters, we would stay with no timeout/1 packet per
  interrupt until the estimator kicks in and changes that

- finally disabling adaptive RX coalescing while providing parameters
  would not be honored, and we would stay with whatever DIM had
  previously determined instead of the user requested parameters

Fixes: b6e0e875 ("net: systemport: Implement adaptive interrupt coalescing")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adaptive TX coalescing is not currently giving us any advantages and
ends up making the CPU spin more frequently until TX completion. Deny
and disable adaptive TX coalescing for now and rely on static
configuration, we can always add it back later.
Reviewed-by: NTal Gilboa <talgi@mellanox.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the hash filter init error
handling case instead of 0, as done elsewhere in this function.

Fixes: 5c31254e ("cxgb4: initialize hash-filter configuration")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VTU miss violations can happen under normal conditions. Don't spam the
kernel log, downgrade the output to debug level only. The statistics
counter will indicate it is happening, if anybody not debugging is
interested.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reported-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Count the numbers of various ATU and VTU violation statistics and
return them as part of the ethtool -S statistics.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use the module_pci_driver() macro to make the code simpler
by eliminating module_init and module_exit calls.
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes the following sparse warning:

drivers/net/ethernet/broadcom/genet/bcmgenet.c:1351:16: warning:
 Using plain integer as NULL pointer
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cotsworks modules fail the checksums - it appears that Cotsworks
reprograms the EEPROM at the end of production with the final product
information (serial, date code, and exact part number for module
options) and fails to update the checksum.

Work around this by detecting the Cotsworks name in the manufacturer
field, and reducing the checksum failures to warnings rather than a
hard error.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds ethtool callback implementation for flash update.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the required driver support for updating the flash or
non volatile memory of the adapter. At highlevel, flash upgrade comprises
of reading the flash images from the input file, validating the images and
writing them to the respective paritions.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds APIs for flash access.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for populating the flash image attributes.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This FW contains several fixes and features

RDMA Features
- SRQ support
- XRC support
- Memory window support
- RDMA low latency queue support
- RDMA bonding support

RDMA bug fixes
- RDMA remote invalidate during retransmit fix
- iWARP MPA connect interop issue with RTR fix
- iWARP Legacy DPM support
- Fix MPA reject flow
- iWARP error handling
- RQ WQE validation checks

MISC
- Fix some HSI types endianity
- New Restriction: vlan insertion in core_tx_bd_data can't be set
  for LB packets

ETH
- HW QoS offload support
- Fix vlan, dcb and sriov flow of VF sending a packet with
  inband VLAN tag instead of default VLAN
- Allow GRE version 1 offloads in RX flow
- Allow VXLAN steering

iSCSI / FcoE
- Fix bd availability checking flow
- Support 256th sge proerly in iscsi/fcoe retransmit
- Performance improvement
- Fix handle iSCSI command arrival with AHS and with immediate
- Fix ipv6 traffic class configuration

DEBUG
- Update debug utilities
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NTomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: NManish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Acked-by: NJason Gunthorpe <jgg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During heavy tx traffic, control messages (sent by liquidio driver to NIC
firmware) sometimes do not get processed in a timely manner.  Reason is:
the low-level metadata of control messages and that of egress network
packets indicate that they have the same priority.

Fix it by setting a higher priority for control messages through the new
ctrl_qpg field in the oct_txpciq struct.  It is the NIC firmware that does
the actual setting of priority by writing to the new ctrl_qpg field; the
host driver treats that value as opaque and just assigns it to pki_ih3->qpg
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add devlink support to netdevsim and use it to implement a simple,
profile based resource controller. Only one controller is needed
per namespace, so the first netdevsim netdevice in a namespace
registers with devlink. If that device is deleted, the resource
settings are deleted.

The resource controller allows a user to limit the number of IPv4 and
IPv6 FIB entries and FIB rules. The resource paths are:
    /IPv4
    /IPv4/fib
    /IPv4/fib-rules
    /IPv6
    /IPv6/fib
    /IPv6/fib-rules

The IPv4 and IPv6 top level resources are unlimited in size and can not
be changed. From there, the number of FIB entries and FIB rule entries
are unlimited by default. A user can specify a limit for the fib and
fib-rules resources:

    $ devlink resource set netdevsim/netdevsim0 path /IPv4/fib size 96
    $ devlink resource set netdevsim/netdevsim0 path /IPv4/fib-rules size 16
    $ devlink resource set netdevsim/netdevsim0 path /IPv6/fib size 64
    $ devlink resource set netdevsim/netdevsim0 path /IPv6/fib-rules size 16
    $ devlink dev reload netdevsim/netdevsim0

such that the number of rules or routes is limited (96 ipv4 routes in the
example above):
    $ for n in $(seq 1 32); do ip ro add 10.99.$n.0/24 dev eth1; done
    Error: netdevsim: Exceeded number of supported fib entries.

    $ devlink resource show netdevsim/netdevsim0
    netdevsim/netdevsim0:
      name IPv4 size unlimited unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables non
        resources:
          name fib size 96 occ 96 unit entry size_min 0 size_max unlimited size_gran 1 dpipe_tables
    ...

With this template in place for resource management, it is fairly trivial
to extend and shows one way to implement a simple counter based resource
controller typical of network profiles.

Currently, devlink only supports initial namespace. Code is in place to
adapt netdevsim to a per namespace controller once the network namespace
issues are resolved.
Signed-off-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rtnl_lock() is used everywhere, and contention is very high.
When someone wants to iterate over alive net namespaces,
he/she has no a possibility to do that without exclusive lock.
But the exclusive rtnl_lock() in such places is overkill,
and it just increases the contention. Yes, there is already
for_each_net_rcu() in kernel, but it requires rcu_read_lock(),
and this can't be sleepable. Also, sometimes it may be need
really prevent net_namespace_list growth, so for_each_net_rcu()
is not fit there.

This patch introduces new rw_semaphore, which will be used
instead of rtnl_mutex to protect net_namespace_list. It is
sleepable and allows not-exclusive iterations over net
namespaces list. It allows to stop using rtnl_lock()
in several places (what is made in next patches) and makes
less the time, we keep rtnl_mutex. Here we just add new lock,
while the explanation of we can remove rtnl_lock() there are
in next patches.

Fine grained locks generally are better, then one big lock,
so let's do that with net_namespace_list, while the situation
allows that.
Signed-off-by: NKirill Tkhai <ktkhai@virtuozzo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can have interrupts left enabled form e.g: the bootloader which used
the network device for network boot. Make sure we have those disabled as
early as possible to avoid spurious interrupts.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When the system contains several BGMAC adapters, it is nice to be able
to tell which one is which by looking at /proc/interrupts. Use the
network device name as a name to request_irq() with.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the National Instruments XGE 1/10G network device.

It uses the EEPROM on the board via NVMEM.
Signed-off-by: NMoritz Fischer <mdf@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the static array and use the generic routine to set the
Ethernet broadcast address.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The commit "cfg80211: make RATE_INFO_BW_20 the default" changed
the index of RATE_INFO_BW_20, but the updates to ath10k missed
the special bandwidth calculation case in
ath10k_update_per_peer_tx_stats().

This will fix below warning,

 WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
 cfg80211_calculate_bitrate+0x174/0x220
 invalid rate bw=1, mcs=9, nss=2

 (unwind_backtrace) from
 (cfg80211_calculate_bitrate+0x174/0x220)
 (cfg80211_calculate_bitrate) from
 (nl80211_put_sta_rate+0x44/0x1dc)from
 (nl80211_put_sta_rate) from
 (nl80211_send_station+0x388/0xaf0)
 (nl80211_get_station+0xa8/0xec)
 [ end trace da8257d6a850e91a ]

Fixes: 842be75c ("cfg80211: make RATE_INFO_BW_20 the default")
Signed-off-by: NChristian Lamparter <chunkeey@gmail.com>
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This patch fixes regression caused by 0c317a02
("cfg80211: support virtual interfaces with different beacon intervals"),
with this change cfg80211 expects the driver to advertize
'beacon_int_min_gcd' to support different beacon intervals in multivap
scenario. This support is added for, QCA988X/QCA99X0/QCA9984/QCA4019.

Verifed AP + mesh bring up on QCA9984 with beacon interval 100msec and
1000msec respectively.
Frimware: firmware-5.bin_10.4-3.5.3-00053

Fixes: 0c317a02 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For WPA encryption, QCA6174 firmware(version: WLAN.RM.4.4) will unblock
data when M4 was sent successfully. For other encryption which didn't need
4-way handshake firmware will unblock the data when peer authorized. Since
TDLS is 3-way handshake host need send authorize cmd to firmware to unblock
data.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TDLS peer do not need WEP key. Setting WEP key will lead
to TDLS setup failure. Add fix to avoid setting WEP key
for TDLS peer.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable TDLS peer inactivity detetion feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS link inactivity detecting.
Set related parameters in TDLS WMI command to enable this feature.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Enable TDLS peer buffer STA feature.
QCA6174 firmware(version: WLAN.RM.4.4) support TDLS peer buffer STA,
it reports this capability through wmi service map in wmi service ready
event. Set related parameter in TDLS WMI command to enable this feature.
Signed-off-by: NYingying Tang <yintang@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.

Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.

This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: NDaniel Mack <daniel@zonque.org>
Reviewed-by: NBjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

wcn36xx_start_tx function retrieves the buffer descriptor from the
channel control queue to start filling tx buffer information. However,
nothing prevents this same buffer to be concurrently accessed in a
concurent tx call, leading to potential buffer coruption and firmware
crash (observed during iperf test). The channel control queue should
only be accessed and updated with the channel lock.

Fix this issue by using a local buffer descriptor which will be copied
in the thread-safe wcn36xx_dxe_tx_frame.

Note that buffer descriptor size is few bytes so the introduced copy
overhead is insignificant. Moreover, this allows to keep the locked
section minimal.
Signed-off-by: NLoic Poulain <loic.poulain@linaro.org>
Signed-off-by: NRamon Fried <rfried@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It appears that the WCN36xx firmware doesn't actually respond to
probe requests. Until it's resolved, switch the probe response
responsibility to the 802.11 layer to allow creation of
hidden SSID AP's.
Signed-off-by: NRamon Fried <rfried@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

QCA9984/QCA99X0/QCA4019 chipsets have 8 memory regions, dump all of them to the
firmware coredump file. Some of the regions need to be read using ioread() so
add new region types for them.
Signed-off-by: NAnilkumar Kolli <akolli@codeaurora.org>
[kvalo: refactoring etc]
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

As QCA9984 needs two region types refactor the code to make it easier add the
new types. No functional changes.
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

FW has Smart Logging feature enabled by default for detecting failures
and processing FATAL_CONDITION_EVENTID (36925 - 0x903D) back to host.

Since ath10k doesn't implement the Smart Logging and FATAL CONDITION
EVENT processing yet, suppressing the unknown event ID warning by moving
this under ATH10K_DBG_WMI.

Simulated the same issue by having associated STA powered off when
ping flood was running from AP backbone. This triggerd STA KICKOUT
in AP followed by FATAL CONDITION event 36925.

Issue was reproduced and verified in below DUT
------------------------------------------------
AP mode of OpenWRT QCA9984 running 6.0.8 with FW ver 10.4-3.5.3-00053
Signed-off-by: NSathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Firmware WLAN.TF.2.1-00014-QCARMSWP-1 now supports reading the board ID
information and also required 9 IRAM bank, which older ath10k version
don't have the support will fail to be enabled, so in order to maintain
the backward compatibility, we need to update the FW API to 6.
Signed-off-by: NRyan Hsu <ryanhsu@codeaurora.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>