ABI 4.x introduced the chained metadata format and made it the
only one possible.  There are cases, however, where the old
format is preferred - mostly to make interoperation with VFs
using ABI 3.x easier for the datapath.  In ABI 5.x we allowed
for more flexibility by selecting the metadata format based
on capabilities.  The default was left to non-chained.

In case of fallback traffic, there is no capability telling the
driver there may be chained metadata.  With a very stripped-
-down FW the default old metadata format would be selected
making the driver drop all fallback traffic.

This patch changes the default selection in the driver. It
should not hurt with old firmwares, because if they don't
advertise RSS they will not produce metadata anyway.  New
firmwares advertising ABI 5.x, however, can depend on the
driver defaulting to chained format.

Fixes: f9380629 ("nfp: advertise support for NFD ABI 0.5")
Suggested-by: NMichael Rapson <michael.rapson@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The legacy MAC address lookup doesn't work well with breakout
cables.  We are probably better off picking random addresses
than the wrong ones in the theoretical scenario where management
FW didn't tell us what the port config is.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For historical reasons we enumerate the vNICs in order.  This means
that if user configures breakout on a multiport card, the first
interface of the second port will have its MAC address changed.

What's worse, when moved from static information (HWInfo) to using
management FW (NSP), more features started depending on the port ids.
Right now in case of breakout first subport of the second port and
second subport of the first port will have their link info swapped.

Revise the ordering scheme so that first subport maintains its address.
Side effect of this change is that we will use base lane ids in
devlink (i.e. 40G ports will be 4 ids apart), e.g.:

pci/0000:04:00.0/0: type eth netdev p6p1
pci/0000:04:00.0/4: type eth netdev p6p2

Note that behaviour of phys_port_id is not changed since there is
a separate id number for the subport there.

Fixes: ec8b1fbe ("nfp: support port splitting via devlink")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When macro MACB_EXT_DESC is defined we end up with two identical
return statements and just one is sufficient. Remove the extra
return.

Detected by CoverityScan, CID#1449361 ("Structurally dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

refcount_t type and corresponding API should be
used instead of atomic_t when the variable is used as
a reference counter. This allows to avoid accidental
refcounter overflows that might lead to use-after-free
situations.
Signed-off-by: NElena Reshetova <elena.reshetova@intel.com>
Signed-off-by: NHans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid Windsor <dwindsor@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Lockdep found an inconsistent lock state when mtk_get_stats64 is called
in user context while NAPI updates MAC statistics in softirq.

Use spin_trylock_bh/spin_unlock_bh fix following lockdep warning.

[   81.321030] WARNING: inconsistent lock state
[   81.325266] 4.12.0-rc1-00035-gd9dda65 #32 Not tainted
[   81.330273] --------------------------------
[   81.334505] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
[   81.340464] ksoftirqd/0/7 [HC0[0]:SC1[1]:HE1:SE0] takes:
[   81.345731]  (&syncp->seq#2){+.?...}, at: [<c054ba3c>] mtk_handle_status_irq.part.6+0x70/0x84
[   81.354219] {SOFTIRQ-ON-W} state was registered at:
[   81.359062]   lock_acquire+0xfc/0x2b0
[   81.362696]   mtk_stats_update_mac+0x60/0x2c0
[   81.367017]   mtk_get_stats64+0x17c/0x18c
[   81.370995]   dev_get_stats+0x48/0xbc
[   81.374628]   rtnl_fill_stats+0x48/0x128
[   81.378520]   rtnl_fill_ifinfo+0x4ac/0xd1c
[   81.382584]   rtmsg_ifinfo_build_skb+0x7c/0xe0
[   81.386991]   rtmsg_ifinfo.part.5+0x24/0x54
[   81.391139]   rtmsg_ifinfo+0x24/0x28
[   81.394685]   __dev_notify_flags+0xa4/0xac
[   81.398749]   dev_change_flags+0x50/0x58
[   81.402640]   devinet_ioctl+0x768/0x85c
[   81.406444]   inet_ioctl+0x1a4/0x1d0
[   81.409990]   sock_ioctl+0x16c/0x33c
[   81.413538]   do_vfs_ioctl+0xb4/0xa34
[   81.417169]   SyS_ioctl+0x44/0x6c
[   81.420458]   ret_fast_syscall+0x0/0x1c
[   81.424260] irq event stamp: 3354692
[   81.427806] hardirqs last  enabled at (3354692): [<c0678168>] net_rx_action+0xc0/0x504
[   81.435660] hardirqs last disabled at (3354691): [<c0678134>] net_rx_action+0x8c/0x504
[   81.443515] softirqs last  enabled at (3354106): [<c0101944>] __do_softirq+0x4b4/0x614
[   81.451370] softirqs last disabled at (3354109): [<c012f0c4>] run_ksoftirqd+0x44/0x80
[   81.459134]
[   81.459134] other info that might help us debug this:
[   81.465608]  Possible unsafe locking scenario:
[   81.465608]
[   81.471478]        CPU0
[   81.473900]        ----
[   81.476321]   lock(&syncp->seq#2);
[   81.479701]   <Interrupt>
[   81.482294]     lock(&syncp->seq#2);
[   81.485847]
[   81.485847]  *** DEADLOCK ***
[   81.485847]
[   81.491720] 1 lock held by ksoftirqd/0/7:
[   81.495693]  #0:  (&(&mac->hw_stats->stats_lock)->rlock){+.+...}, at: [<c054ba14>] mtk_handle_status_irq.part.6+0x48/0x84
[   81.506579]
[   81.506579] stack backtrace:
[   81.510904] CPU: 0 PID: 7 Comm: ksoftirqd/0 Not tainted 4.12.0-rc1-00035-gd9dda65 #32
[   81.518668] Hardware name: Mediatek Cortex-A7 (Device Tree)
[   81.524208] [<c0113dc4>] (unwind_backtrace) from [<c010e3f0>] (show_stack+0x20/0x24)
[   81.531899] [<c010e3f0>] (show_stack) from [<c03f9c64>] (dump_stack+0xb4/0xe0)
[   81.539072] [<c03f9c64>] (dump_stack) from [<c017e970>] (print_usage_bug+0x234/0x2e0)
[   81.546846] [<c017e970>] (print_usage_bug) from [<c017f058>] (mark_lock+0x63c/0x7bc)
[   81.554532] [<c017f058>] (mark_lock) from [<c017fe90>] (__lock_acquire+0x654/0x1bfc)
[   81.562217] [<c017fe90>] (__lock_acquire) from [<c0181d04>] (lock_acquire+0xfc/0x2b0)
[   81.569990] [<c0181d04>] (lock_acquire) from [<c054b76c>] (mtk_stats_update_mac+0x60/0x2c0)
[   81.578283] [<c054b76c>] (mtk_stats_update_mac) from [<c054ba3c>] (mtk_handle_status_irq.part.6+0x70/0x84)
[   81.587865] [<c054ba3c>] (mtk_handle_status_irq.part.6) from [<c054c2b8>] (mtk_napi_tx+0x358/0x37c)
[   81.596845] [<c054c2b8>] (mtk_napi_tx) from [<c06782ec>] (net_rx_action+0x244/0x504)
[   81.604533] [<c06782ec>] (net_rx_action) from [<c01015c4>] (__do_softirq+0x134/0x614)
[   81.612306] [<c01015c4>] (__do_softirq) from [<c012f0c4>] (run_ksoftirqd+0x44/0x80)
[   81.619907] [<c012f0c4>] (run_ksoftirqd) from [<c0154680>] (smpboot_thread_fn+0x14c/0x25c)
[   81.628110] [<c0154680>] (smpboot_thread_fn) from [<c014f8cc>] (kthread+0x150/0x180)
[   81.635798] [<c014f8cc>] (kthread) from [<c0109290>] (ret_from_fork+0x14/0x24)
Signed-off-by: NSean Wang <sean.wang@mediatek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix compilation warning
qed_iwarp.c:1721:5: warning: ll2_syn_handle may be used
uninitialized in this function
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable mlx4_log_num_mgm_entry_size is only called in main.c.

CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: NZhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: NYuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pointer hdr in netxen_setup_minidump() is set but never used, thus
should be removed.
Signed-off-by: NChristos Gkekas <chris.gekas@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.

Fixes: 8ed66f0e ("geneve: implement support for IPv6-based tunnels")
Cc: John W. Linville <linville@tuxdriver.com>
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's not a good idea to add the same hlist_node to two different hash lists.
This leads to various hard to debug memory corruptions.

Fixes: b1be00a6 ("vxlan: support both IPv4 and IPv6 sockets in a single vxlan device")
Signed-off-by: NJiri Benc <jbenc@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If mlx5 is set to be built-in and mlxfw as a module, we
get a link error:

drivers/built-in.o: In function `mlx5_firmware_flash':
(.text+0x5aed72): undefined reference to `mlxfw_firmware_flash'

Since we don't want to mandate selecting mlxfw for mlx5 users, we
use the IS_REACHABLE macro to make sure that a stub is exposed
to the caller.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NJakub Kicinski <kubakici@wp.pl>
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The HP lt4132 LTE/HSPA+ 4G Module (03f0:a31d) is a rebranded Huawei
ME906s-158 device. It, like the ME906s-158, requires the "NDP to end"
quirk for correct operation.
Signed-off-by: NTore Anderson <tore@fud.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a985343b ("vxlan: refactor verification and application of
configuration") modified vxlan device creation, and replaced the
assignment of vxlan->net to src_net with dev_net(netdev) in ->setup().

But dev_net(netdev) is not the same as src_net. At the time ->setup()
is called, dev_net hasn't been set yet, so we end up creating the
socket for the vxlan device in init_net.

Fix this by bringing back the assignment of vxlan->net during device
creation.

Fixes: a985343b ("vxlan: refactor verification and application of configuration")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Reviewed-by: NMatthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use function set_loopback in phy_driver to setup phy loopback
when doing ethtool self test.
Signed-off-by: NLin Yun Sheng <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add set_loopback in phy_driver, which is used by MAC
driver to enable or disable phy loopback. it also add a generic
genphy_loopback function, which use BMCR loopback bit to enable
or disable loopback.
Signed-off-by: NLin Yun Sheng <linyunsheng@huawei.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CDC-NCM driver can require large amounts of memory to create
skb's and this can be a problem when the memory becomes fragmented.

This especially affects embedded systems that have constrained
resources but wish to maximise the throughput of CDC-NCM with 16KiB
NTB's.

The issue is after running for a while the kernel memory can become
fragmented and it needs compacting.
If the NTB allocation is needed before the memory has been compacted
the atomic allocation can fail which can cause increased latency,
large re-transmissions or disconnections depending upon the data
being transmitted at the time.
This situation occurs for less than a second until the kernel has
compacted the memory but the failed devices can take a lot longer to
recover from the failed TX packets.

To ease this temporary situation I modified the CDC-NCM TX path to
temporarily switch into a reduced memory mode which allocates an NTB
that will fit into a USB_CDC_NCM_NTB_MIN_OUT_SIZE (default 2048 Bytes)
sized memory block and only transmit NTB's with a single network frame
until the memory situation is resolved.
Each time this issue occurs we wait for an increasing number of
reduced size allocations before requesting a full size one to not
put additional pressure on a low memory system.

Once the memory is compacted the CDC-NCM data can resume transmitting
at the normal tx_max rate once again.
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Reviewed-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP has different physical queue requirements than RoCE
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When computing how much memory is required for the different hw clients
iWARP protocol should be taken into account
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces error handling for errors that occurred during
connection establishment.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch takes care of active/passive disconnect flows.
Disconnect flows can be initiated remotely, in which case a async event
will arrive from peer and indicated to qedr driver. These
are referred to as exceptions. When a QP is destroyed, it needs to check
that it's associated ep has been closed.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the active side connect.
Offload a connection, process MPA reply and send RTR.
In some of the common passive/active functions, the active side
will work in blocking mode.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements the passive side connect.
It addresses pre-allocating resources, creating a connection
element upon valid SYN packet received. Calling upper layer and
implementation of the accept/reject calls.

Error handling is not part of this patch.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the ability to add and remove listeners and identify
whether the SYN packet received is intended for iWARP or not. If
a listener is not found the SYN packet is posted back to the chip.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP handles incoming SYN packets using the ll2 interface. This patch
implements ll2 setup and teardown. Additional ll2 connections will
be used in the future which are not part of this patch series.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new connection type for iWARP ll2 connections for setting
correct ll2 filters and connection type to FW.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make some names more generic as they will be used by iWARP too.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds iWARP support for flows that have common code
between RoCE and iWARP, such as initialization, teardown and
qp setup verbs: create, destroy, modify, query.
It introduces the iWARP specific files qed_iwarp.[ch] and
iwarp_common.h
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

iWARP personality introduced the need for differentiating in several
places in the code whether we are RoCE, iWARP or either. This
leads to introducing new macros for querying the personality.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix out-of-date comment.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trivial fix to spelling mistake in mlx5_core_dbg debug message
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously the flower offloads never sends messages to the hardware,
and never registers a handler for receiving messages from hardware.
This patch enables the flower offloads to send control messages to
hardware when adding and removing flow rules. Additionally it
registers a control message rx handler for receiving stats updates
from hardware for each offloaded flow.

Additionally this patch adds 4 control message types; Add, modify and
delete flow, as well as flow stats. It also allows
nfp_flower_cmsg_get_data() to be used outside of cmsg.c.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously there was no way of updating flow rule stats after they
have been offloaded to hardware. This is solved by keeping track of
stats received from hardware and providing this to the TC handler
on request.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds metadata describing the mask id of each flow and keeps track of
flows installed in hardware. Previously a flow could not be removed
from hardware as there was no way of knowing if that a specific flow
was installed. This is solved by storing the offloaded flows in a
hash table.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds push vlan, pop vlan, output and drop action capabilities
to flower offloads.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extends matching capabilities for flower offloads to include vlan,
layer 2, layer 3 and layer 4 type matches. This includes both exact
and wildcard matching.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extends the flower flow add function by calculating which match
fields are present in the flower offload structure and allocating
the appropriate space to describe these.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a flower based TC offload handler for representor devices, this
is in addition to the bpf based offload handler. The changes in this
patch will be used in a follow-up patch to add tc flower offload to
the NFP.

The flower app enables tc offloads on representors by default.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>