Signed-off-by: NAndrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This change makes the fcoe Rx threads have the same nice value
as lpfc and qla2xxx Rx threads.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

In fcoe_check_wait_queue() the queue length could temporarily drop to 0,
before the last frame was successfully sent.  This resulted in out of order
data frames within a single sequence, leading to IO timeout errors.

This builds on the approach from Vasu Dev to only fix the queue management in
fcoe_check_wait_queue, where my first patch added locking to the transmit
path even when the pending queue was not in use.

This patch continues to use fcoe_pending_queue.qlen instead of introducing a
new length counter, but takes precautions to ensure it never drops to 0 before
the final frame in the queue has successfully been passed to the netdev qdisc
layer.  It also includes some cleanup of fcoe_check_wait_queue and removes the
fcoe_insert_wait_queue(_head) wrapper functions.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

frames followed by these errors in log.

	[sdp] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE,SUGGEST_OK
	[sdp] Sense Key : Aborted Command [current]
	[sdp] Add. Sense: Data phase error

This was causing some test apps to exit due to write failure under heavy
load.

This was due to a race around adding and removing tx frame skb in
fcoe_pending_queue, Chris Leech helped me to find that brief unlocking
period when pulling skb from fcoe_pending_queue in various contexts
(fcoe_watchdog and fcoe_xmit) and then adding skb back into fcoe_pending_queue
up on a failed fcoe_start_io could change skb/tx frame order in
fcoe_pending_queue. Thanks Chris.

This patch allows only single context to pull skb from fcoe_pending_queue
at any time to prevent above described ordering issue/race by use of
fcoe_pending_queue_active flag.

This patch simplified fcoe_watchdog with modified fcoe_check_wait_queue by
use of FCOE_LOW_QUEUE_DEPTH instead previously used several conditionals
to clear and set lp->qfull.

I think FCOE_MAX_QUEUE_DEPTH with FCOE_LOW_QUEUE_DEPTH  will work better
in re/setting lp->qfull and these could be fine tuned for performance.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use kfree_skb instead of kfree for struct sk_buff pointers.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We shouldn't be altering inbound frames.
Signed-off-by: NYi Zou <yi.zou@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The registration function shouldn't initialize the mutex or
list head. The fcoe SW transport should initialize itself
before registering.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Use helper functions for watchdog timer setup.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Comment from "Andrew Morton <akpm@linux-foundation.org>"

> +{
> +     return (struct fcoe_softc *)lport_priv(lp);

unneeded/undesirable cast of void*.  There are probably zillions of
instances of this - there always are.

This whole inline function was unnecessary. The FCoE layer knows
that it's data structure is stored in the lport private data, it
can just access it from lport_priv().
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) There were a few functions with a strange layout, i.e. all
   arguments on the second line, when not necessary.

   Where ever possible I moved the return value to the same line
   as the function name. However, when the line was too long
   to have a single argument on the same line I moved the
   return value to above line. For example:

   <short return> <function name>(<arg 1>, <arg2>)

   and

   <very long return value>
   <function name>(<arg1>,
		   <arg2>)

2) Removed one extra whitespace line

3) Fixed two typos
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

1) Added '()' for function names in kerneldoc comments

2) Changed comment bookends from '**/' to '*/'. The comment on the the
   mailing list was that '**/' "is consistently unconventional.  Not
   wrong, just odd." The Documentation/kernel-doc-nano-HOWTO.txt
   states that kerneldoc comment blocks should end with '**/' but most
   (if not all) instance I found under drivers/scsi/ were only using
   the '*/' so I converted to that style.

3) Removed incorrect linebreaks in kerneldoc comments where found

4) Removed a few unnecessary blank comment lines in kerneldoc comment
   blocks
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Made the comments more like the comments for struct scsi_host_template.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

If we've just created an interface and the an rport is
logging in we may have a request on the wire (say PRLI).
If we destroy the interface, we'll go through each rport
on the disc->rports list and set each rport's state to NONE.
Then the lport will reset the EM. The EM reset will send a
CLOSED event to the prli_resp() handler which will notice
that the state != PRLI. In this case it frees the frame
pointer, decrements the refcount and unlocks the rport.

The problem is that there isn't a frame in this case. It's
just a pointer with an embedded error code. The free causes
an Oops.

This patch moves the error checking to be before the state
checking.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Just rename the variable as per our naming convention.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We only need to use this macro when assigning a value to
rport->dd_data. All other accesses should just use dd_data.
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When a sequence cannot be delivered to the target, the local
port will schedule retries, While this process is in progress,
if we destroy the FCoE interface, the fcoe_sw_destroy routine is
entered, and the fc_exch_mgr_free(lp->emp) is called.  Thus
if fc_exch_alloc() is called when retrying the sequence,
the mempool_alloc() will fail to allocate the exchange because
the mempool of the exchange manager has already been released.
This patch is to cancel any pending retry work of the local
port before we start to destroy the interface.

Also, when resetting the local port, we should also stop the
scheduled pending retries.
Signed-off-by: NSteve Ma <steve.ma@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fc_fcp_complete_locked detected data underrun in this case and set
the FC_DATA_UNDRUN but that was ignored by fc_io_compl for all cases
including read underrun.

Added code to not to ignore FC_DATA_UNDRUN for read IO and instead
suggested scsi-ml to retry cmd to  recover from lost data frame.

Not sure if it is okay to ignore FC_DATA_UNDRUN for other case, so let
code as is for other cases but removed or-ing with zero valued fsp->cdb_status
for those cases.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

This allows any rport ELS to retry on LS_RJT.

The rport error handling would only retry on resource allocation failures
and exchange timeouts.  I have a target that will occasionally reject PLOGI
when we do a quick LOGO/PLOGI.  When a critical ELS was rejected, libfc would
fail silently leaving the rport in a dead state.

The retry count and delay are managed by fc_rport_error_retry.  If the retry
count is exceeded fc_rport_error will be called.  When retrying is not the
correct course of action, fc_rport_error can be called directly.
Signed-off-by: NChris Leech <christopher.leech@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fcoe_xmit could call fc_pause in case the pending skb queue len is larger
than FCOE_MAX_QUEUE_DEPTH, the fc_pause was trying to grab lport->lp_muex to
change lport->link_status and that had these issues :-

1. The fcoe_xmit was getting called with bh disabled, thus causing
"BUG: scheduling while atomic" when grabbing lport->lp_muex with bh disabled.

2. fc_linkup and fc_linkdown function calls lport_enter function with
lport->lp_mutex held and these enter function in turn calls fcoe_xmit to send
lport related FC frame, e.g. fc_linkup => fc_lport_enter_flogi to send flogi
req. In this case grabbing the same lport->lp_mutex again in fc_puase from
fcoe_xmit would cause deadlock.

The lport->lp_mutex was used for setting FC_PAUSE in fcoe_xmit path but
FC_PAUSE bit was not used anywhere beside just setting and clear this
bit in lport->link_status, instead used a separate field qfull in fc_lport
to eliminate need for lport->lp_mutex to track pending queue full condition
and in turn avoid above described two locking issues.

Also added check for lp->qfull in fc_fcp_lport_queue_ready to trigger
SCSI_MLQUEUE_HOST_BUSY when lp->qfull is set to prevent more scsi-ml cmds
while lp->qfull is set.

This patch eliminated FC_LINK_UP and FC_PAUSE and instead used dedicated
fields in fc_lport for this, this simplified all related conditional
code.

Also removed fc_pause and fc_unpause functions and instead used newly added
lport->qfull directly in fcoe.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

The fc_seq_start_next grabs ep->ex_lock but this lock was already held here,
so instead called fc_seq_start_next_locked to avoid soft lockup.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

Cleanup exchange held due to RRQ when RRQ exch times out, in this case the
ABTS is already done causing RRQ req therefore proceeding with cleanup in
fc_exch_rrq_resp should be okay to restore exch resource.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

When a rport goes away, libFC does a plogi which will reset exchanges
    at the rport. Clean exchanges at our end, both in transport and libFC.
    If transport hooks into exch_mgr_reset, it will call back into
    fc_exch_mgr_reset() to clean up libFC exchanges.
Signed-off-by: NAbhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

fc_exch_mgr structure is private to fc_exch.c. To export exch_mgr_reset to
transport, transport needs access to the exch manager. Change
exch_mgr_reset to use lport param which is the shared structure between
libFC and transport.

Alternatively, fc_exch_mgr definition can be moved to libfc.h so that lport
can be accessed from mp*.
Signed-off-by: NAbhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

We currently try to spin up drives connected to standby and unavailable
ports.  This will never succeed and wastes a lot of time.  Fail quickly
if the sense data reports the port is in standby or unavailable state.
Reported-by: NNarayanan Rengarajan <narayanan.rengarajan@hp.com>
Tested-by: NNarayanan Rengarajan <narayanan.rengarajan@hp.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc: Run sbc610 USB fixup code only on the appropriate platform.

[airlied: you shall not retype patches from other trees half asleep]
Signed-of-by: NDave Airlie <airlied@redhat.com>

commit a969e76a (powerpc: Correct USB
support for GE Fanuc SBC610) introduced a fixup for NEC usb controllers.
This fixup should only run on GEF SBC610 boards.

Fixes Fedora bug #486511.
(https://bugzilla.redhat.com/show_bug.cgi?id=486511)
Signed-off-by: NTony Breeds <tony@bakeyournoodle.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: ixp4xx - Fix qmgr_request_queue build failure
  crypto: api - Fix module load deadlock with fallback algorithms

There is another user of IXP4xx queue manager, fix it.
Signed-off-by: NKrzysztof Hałasa <khc@pm.waw.pl>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: don't allow setuid to succeed if the user does not have rt bandwidth
  sched_rt: don't start timer when rt bandwidth disabled

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86: oprofile: don't set counter width from cpuid on Core2
  x86: fix init_memory_mapping() to handle small ranges

* 'tracing/mmiotrace' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86 mmiotrace: fix race with release_kmmio_fault_page()
  x86 mmiotrace: improve handling of secondary faults
  x86 mmiotrace: split set_page_presence()
  x86 mmiotrace: fix save/restore page table state
  x86 mmiotrace: WARN_ONCE if dis/arming a page fails
  x86: add far read test to testmmiotrace
  x86: count errors in testmmiotrace.ko

Merge branch 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  rcu: Teach RCU that idle task is not quiscent state at boot

* master.kernel.org:/home/rmk/linux-2.6-arm:
  [ARM] fix lots of ARM __devexit sillyness
  [ARM] 5417/1: Set the correct cacheid for ARMv6 CPUs with ARMv7 style MMU
  [ARM] 5416/1: Use unused address in v6_early_abort
  [ARM] 5411/1: S3C64XX: Fix EINT unmask
  [ARM] at91: fix for Atmel AT91 powersaving
  [ARM] RiscPC: Fix etherh oops

`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
`pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The cacheid_init() function assumes that if cpu_architecture() returns
7, the caches are VIPT_NONALIASING. The cpu_architecture() function
returns the version of the supported MMU features (e.g. TEX remapping)
but it doesn't make any assumptions about the cache type. The patch adds
the checking of the Cache Type Register for the ARMv7 format.
Signed-off-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The target of the strex instruction to clear the exlusive monitor
is currently the top of the stack.  If the store succeeeds this
corrupts r0 in pt_regs.  Use the next stack location instead of
the current one to prevent any chance of corrupting an in-use
address.
Signed-off-by: NSeth Forshee <seth.forshee@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>