- 29 11月, 2011 3 次提交
-
-
this will allow to use gpio_is_valid Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-
this will simplify the switch to the DT and later to the platform_device Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 28 11月, 2011 14 次提交
-
-
switch the rtc drivers to resource and pass it via platform_device Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-
on all at91 have the Advanced Interrupt Controller starts at address 0xfffff000 Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
we will select now the DBGU used by the soc at Kconfig level For the DEBUG_LL and early_printk this will allow to select which DBGU to use this will also allow to select them when multiple SOC are enabled Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
switch the watchdog drivers to resource and pass it via platform_device Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NWim Van Sebroeck <wim@iguana.be>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
never used in the kernel Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
now sam9_smc_configure will take as first parameter is the SMC id Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
this will allow to ioremap the register of the PIT, PMC and others and make the code soc independent Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
-
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Reviewed-by: NRyan Mallon <rmallon@gmail.com>
-
We have a clocksource which renders CLOCK_TICK_RATE useless. Define it to a bogus value to get rid of some ifdeffery. use local LATCH for at91rm9200 timer but keep it for A91X40 as we do not use a clocksource Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
-
- 22 11月, 2011 4 次提交
-
-
由 Jamie Iles 提交于
Both at91 and avr32 defines its own platform data structure for the macb driver and both share common structures though at91 includes a currently unused phy_irq_pin. Create a common macb_platform_data for macb that both at91 and avr32 can use. In future we can use this to support other architectures that use the same IP block with the macb driver. v2: rename eth_platform_data to macb_platform_data and allow at91_ether to share the platform data with macb. Signed-off-by: NJamie Iles <jamie@jamieiles.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Jamie Iles 提交于
The macb driver expects clocks with the names "pclk" and "hclk". We currently provide "macb_clk" but to fit in line with other architectures (namely AVR32), provide "pclk" and a fake "hclk". Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> Signed-off-by: NJamie Iles <jamie@jamieiles.com> Acked-by: NDavid S. Miller <davem@davemloft.net> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
-
由 Al Viro 提交于
altroot support has been gone for years, along with arch/*/asm/namei.h; looks like a dummy survivor that sat it out in microblaze tree... Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
-
由 Al Viro 提交于
wrong register returned... Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
- 20 11月, 2011 1 次提交
-
-
由 Avi Kivity 提交于
Prevent tracing of preempt_disable() in get_cpu_var() in kvm_clock_read(). When CONFIG_DEBUG_PREEMPT is enabled, preempt_disable/enable() are traced and this causes the function_graph tracer to go into an infinite recursion. By open coding the preempt_disable() around the get_cpu_var(), we can use the notrace version which prevents preempt_disable/enable() from being traced and prevents the recursion. Based on a similar patch for Xen from Jeremy Fitzhardinge. Tested-by: NGleb Natapov <gleb@redhat.com> Acked-by: NSteven Rostedt <rostedt@goodmis.org> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
- 18 11月, 2011 4 次提交
-
-
由 David S. Miller 提交于
Some of the sun4v code patching occurs in inline functions visible to, and usable by, modules. Therefore we have to patch them up during module load. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 David S. Miller 提交于
To handle the large physical addresses, just make a simple wrapper around remap_pfn_range() like MIPS does. Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Rafael J. Wysocki 提交于
Fix build regression introduced by commit 056879d2 (ARM: mach-shmobile: sh7372 A3SP no_suspend_console fix) by moving the intialization of the A3SP domain to a separate function and providing an empty definition of it for CONFIG_PM unset. Reported-and-tested-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de> Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
-
由 Russell King 提交于
These two syscalls were introduced during the last merge window. Add the entries into the ARM call tables for them. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
- 17 11月, 2011 14 次提交
-
-
由 Alexander Graf 提交于
This reverts commit a15bd354. It exceeded the padding on the SREGS struct, rendering the ABI backwards-incompatible. Conflicts: arch/powerpc/kvm/powerpc.c include/linux/kvm.h Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Gleb Natapov 提交于
Signed-off-by: NGleb Natapov <gleb@redhat.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Gleb Natapov 提交于
Support guest/host-only profiling by switch perf msrs on a guest entry if needed. Signed-off-by: NGleb Natapov <gleb@redhat.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Gleb Natapov 提交于
Some cpus have special support for switching PERF_GLOBAL_CTRL msr. Add logic to detect if such support exists and works properly and extend msr switching code to use it if available. Also extend number of generic msr switching entries to 8. Signed-off-by: NGleb Natapov <gleb@redhat.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Christian Borntraeger 提交于
KVM on s390 always had a sync mmu. Any mapping change in userspace mapping was always reflected immediately in the guest mapping. - In older code the guest mapping was just an offset - In newer code the last level page table is shared Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NCarsten Otte <cotte@de.ibm.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Christian Borntraeger 提交于
There is a potential host deadlock in the tprot intercept handling. We must not hold the mmap semaphore while resolving the guest address. If userspace is remapping, then the memory detection in the guest is broken anyway so we can safely separate the address translation from walking the vmas. Signed-off-by: NChristian Borntraeger <borntraeger@de.ibm.com> Signed-off-by: NCarsten Otte <cotte@de.ibm.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Cornelia Huck 提交于
SIGP sense running may cause an intercept on higher level virtualization, so handle it by checking the CPUSTAT_RUNNING flag. Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NCarsten Otte <cotte@de.ibm.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Cornelia Huck 提交于
CPUSTAT_RUNNING was implemented signifying that a vcpu is not stopped. This is not, however, what the architecture says: RUNNING should be set when the host is acting on the behalf of the guest operating system. CPUSTAT_RUNNING has been changed to be set in kvm_arch_vcpu_load() and to be unset in kvm_arch_vcpu_put(). For signifying stopped state of a vcpu, a host-controlled bit has been used and is set/unset basically on the reverse as the old CPUSTAT_RUNNING bit (including pushing it down into stop handling proper in handle_stop()). Cc: stable@kernel.org Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com> Signed-off-by: NCarsten Otte <cotte@de.ibm.com> Signed-off-by: NAvi Kivity <avi@redhat.com>
-
由 Will Deacon 提交于
On PPC64, put_sigset_t converts a sigset_t to a compat_sigset_t before copying it to userspace. There is a typo in the case that we have 4 words to copy, meaning that we corrupt the compat_sigset_t. It appears that _NSIG_WORDS can't be greater than 2 at the moment so this code is probably always optimised away anyway. Signed-off-by: NWill Deacon <will.deacon@arm.com> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Benjamin Herrenschmidt 提交于
The Documentation/memory-barriers.txt document requires that atomic operations that return a value act as a memory barrier both before and after the actual atomic operation. Our current implementation doesn't guarantee this. More specifically, while a load following the isync can not be issued before stwcx. has completed, that completion doesn't architecturally means that the result of stwcx. is visible to other processors (or any previous stores for that matter) (typically, the other processors L1 caches can still hold the old value). This has caused an actual crash in RCU torture testing on Power 7 This fixes it by changing those atomic ops to use new macros instead of RELEASE/ACQUIRE barriers, called ATOMIC_ENTRY and ATMOIC_EXIT barriers, which are then defined respectively to lwsync and sync. I haven't had a chance to measure the performance impact (or rather what I measured with kernel compiles is in the noise, I yet have to find a more precise benchmark) Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
-
由 Kyle Moffett 提交于
Recent binutils refuses to assemble AltiVec opcodes when in e500/SPE mode, as some of those opcodes alias the "SPE" instructions. This triggers an ancient binutils version check even when building a kernel with CONFIG_ALTIVEC disabled. In theory, the check could be conditionalized on CONFIG_ALTIVEC, but in practice it has long outlived its utility. It is virtually impossible to find binutils older than 2.12.1 (released 2002) in the wild anymore. Even ancient RedHat Enterprise Linux 4 has binutils-2.14. To fix the kernel build when done natively on e500 systems with this new binutils, the test is simply removed. Signed-off-by: NKyle Moffett <Kyle.D.Moffett@boeing.com> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Kumar Gala 提交于
With the introduction of CONFIG_PPC_ADV_DEBUG_REGS user space debug is broken on Book-E 64-bit parts that support delayed debug events. When switch_booke_debug_regs() sets DBCR0 we'll start getting debug events as MSR_DE is also set and we aren't able to handle debug events from kernel space. We can remove the hack that always enables MSR_DE and loads up DBCR0 and just utilize switch_booke_debug_regs() to get user space debug working again. We still need to handle critical/debug exception stacks & proper save/restore of state for those exception levles to support debug events from kernel space like we have on 32-bit. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Kumar Gala 提交于
All of DebugException is already protected by CONFIG_PPC_ADV_DEBUG_REGS there is no need to have another such ifdef inside the function. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-
由 Kumar Gala 提交于
We had an existing ifdef for 4xx & BOOKE processors that got changed to CONFIG_PPC_ADV_DEBUG_REGS. The define has nothing to do with CONFIG_PPC_ADV_DEBUG_REGS. The define really should be: #if defined(CONFIG_4xx) || defined(CONFIG_BOOKE) and not #ifdef CONFIG_PPC_ADV_DEBUG_REGS Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
-