Add support for configuring classification rules using the
ethtool::rxnfc API.  This is useful to program the switch's CFP/TCAM to
redirect specific packets to specific ports/queues for instance. For
now, we allow any kind of IPv4 5-tuple matching.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add Compact Field Processor definitions for the Broadcom Starfighter 2
and compatible versions of the switch.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, all traffic goes to queue 0, re-configure the traffic
classes to quality of service mapping such that priority X maps to queue
X, where X is from 0 through 7.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SGMII (internal PHY) can report decode errors via an interrupt.  It
can also report autonegotiation status changes, but we don't need to track
those.  The SGMII can recover automatically from most decode errors, so
we only reset the interface if we get multiple consecutive errors.

It's possible for bogus decode errors to be reported while the link is
being brought up.  The interrupt is registered when the interface is
opened, and it's enabled after the link is up.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EMAC driver does not support wake-on-lan, but there is still
code left-over that partially enables it.  Remove that code and a few
macros that support it.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

emac_mac_start() uses information from the external PHY to program
the MAC, so it makes no sense to call it before the link is up.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Regardless of how the external PHY is configured, the internal PHY
(the "SGMII" block) is capable of configuring the SGMII link automatically.
When the external PHY link comes up, regardless of how it is configured,
the SGMII link is configured automatically.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PHY driver is attached only when the driver calls
phy_connect_direct().  Calling phy_attached_print() to display
information about the PHY driver prior to that point is meaningless.
The interface can be brought down, a new PHY driver can be loaded,
and the interface then brought back up.  This is the correct time
to display information about the attached driver.

Since phy_attached_print() also prints information about the
interrupt, that needs to be set as well.
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that DSA exposes the bridge device pointer to which a port belongs,
use it when programming the port based VLANs and thus remove the cache.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Upon reception of the NETDEV_CHANGEUPPER, a leaving port is already
unbridged, so reflect this by assigning the port's bridge_dev pointer to
NULL before calling the port_bridge_leave DSA driver operation.

Now that the bridge_dev pointer is exposed to the drivers, reflecting
the current state of the DSA switch fabric is necessary for the drivers
to adjust their port based VLANs correctly.

Pass the bridge device pointer to the port_bridge_leave operation so
that drivers have all information to re-program their chips properly,
and do not need to cache it anymore.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the ports[DSA_MAX_PORTS] array of the dsa_switch structure for a
zero-length array, allocated at the same time as the dsa_switch
structure itself. A dsa_switch_alloc() helper is provided for that.

This commit brings no functional change yet since we pass DSA_MAX_PORTS
as the number of ports for the moment. Future patches can update the DSA
drivers separately to support dynamic number of ports.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The limitation to 10/100Mbit speeds on R-Car Gen3 is valid for R-Car H3
ES1.0 only. Check for the exact SoC model to allow 1Gbps on newer
revisions of R-Car H3, and on R-Car M3-W.
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch enables tx and rx clock internal delay modes (TDM and RDM).

This is to address a failure in the case of 1Gbps communication using the
by salvator-x board with the KSZ9031RNX phy. This has been reported to
occur with both the r8a7795 (H3) and r8a7796 (M3-W) SoCs.

With this change APSR internal delay modes are enabled for
"rgmii-id", "rgmii-rxid" and "rgmii-txid" phy modes as follows:

phy mode   | ASPR delay mode
-----------+----------------
rgmii-id   | TDM and RDM
rgmii-rxid | RDM
rgmii-txid | TDM
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macro is returning ETIME which means various checks to see if
the returned err is less than zero never work. I believe a -ETIME
should be returned instead.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398318 ("Logically Dead Code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check on err < 0 is redundant and can be removed. Detected
by CoverityScan, CID#1398321 ("Logically Dead Code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enable userspace to send error replies for invalid tunnels
Acked-by: NHarald Welte <laforge@netfilter.org>
Signed-off-by: NAndreas Schultz <aschultz@tpip.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The rcu read lock is hold by default in the ip input path. There
is no need to hold it twice in the socket recv decapsulate code path.
Signed-off-by: NAndreas Schultz <aschultz@tpip.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If IPV6 has not been enabled in the underlying kernel, we must avoid
calling IPV6 procedures in rdma_cm.ko.

This requires using "IS_ENABLED(CONFIG_IPV6)" in "if" statements
surrounding any code which calls external IPV6 procedures.

In the instance fixed here, procedure cma_bind_addr() called
ipv6_addr_type() -- which resulted in calling external procedure
__ipv6_addr_type().

Fixes: 6c26a771 ("RDMA/cma: fix IPv6 address resolution")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Spencer Baugh <sbaugh@catern.com>
Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: NMoni Shoua <monis@mellanox.com>
Signed-off-by: NLeon Romanovsky <leon@kernel.org>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

8000 series adapters support filtering VXLAN, NVGRE and GENEVE traffic
 based on inner fields, and when the NIC recognises such traffic, it
 does not match unencapsulated traffic filters any more.  So add catch-
 all filters for encapsulated traffic on supporting platforms.
Although recognition of VXLAN and GENEVE is based on UDP ports, and thus
 will not occur until the driver (on the primary PF) notifies the
 firmware of UDP ports to use, NVGRE will always be recognised, hence
 without this patch 8000 series adapters will drop all NVGRE traffic.

Partly based on patches by Jon Cooper <jcooper@solarflare.com>.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rationalise several debug-or-warnings printks using netif_cond_dbg
 to make output more consistent.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the NIC is switched from full-featured to low-latency, encapsulated
 filters are no longer available, and this causes errors. This patch
 removes those filters from the filter table on restore.
Also, if filters which are removed by the above, or which we fail to
 insert when restoring filters, were UC, MC or broadcast default
 filters, invalidate the corresponding vlan->default_filters entry.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's Broadcom PHY simply described as single-port
RGMII 10/100/1000BASE-T PHY. It requires disabling delay skew and GTXCLK
bits.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With some gcc versions, we get a warning about the eicon driver,
and that currently shows up as the only remaining warning in one
of the build bots:

In file included from ../drivers/isdn/hardware/eicon/message.c:30:0:
eicon/message.c: In function 'mixer_notify_update':
eicon/platform.h:333:18: warning: array subscript is above array bounds [-Warray-bounds]

The code is easily changed to open-code the unusual PUT_WORD() line
causing this to avoid the warning.

Cc: stable@vger.kernel.org
Link: http://arm-soc.lixom.net/buildlogs/stable-rc/v4.4.45/Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is adds support for the PHYs in the KSZ8795 5port managed switch.

It will allow to detect the link between the switch and the soc
and uses the same read_status functions as the KSZ8873MLL switch.
Signed-off-by: NSean Nyekjaer <sean.nyekjaer@prevas.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The use of the passed through netlink src_net to check for a
cross netns operation was wrong. Using the GTP socket and the
GTP netdevice is always correct (even if the netdev has been
moved to new netns after link creation).

Remove the now obsolete net field from gtp_dev.
Signed-off-by: NAndreas Schultz <aschultz@tpip.net>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

3GPP TS 29.281 and 3GPP TS 29.060 imply that GTP-U packets should be
sent with the DF bit cleared. For example 3GPP TS 29.060, Release 8,
Section 13.2.2:

> Backbone router: Any router in the backbone may fragment the GTP
> packet if needed, according to IPv4.
Signed-off-by: NAndreas Schultz <aschultz@tpip.net>
Acked-by: NHarald Welte <laforge@netfilter.org>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Auto-load the module when userspace asks for the gtp netlink
family.
Signed-off-by: NAndreas Schultz <aschultz@tpip.net>
Acked-by: NHarald Welte <laforge@netfilter.org>
Acked-by: NPablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resuming from RPM can happen while already holding
dev->mode_config.mutex. This means we can't actually handle fbcon in
any RPM resume workers, since restoring fbcon requires grabbing
dev->mode_config.mutex again. So move the fbcon suspend/resume code into
it's own worker, and rely on that instead to avoid deadlocking.

This fixes more deadlocks for runtime suspending the GPU on the ThinkPad
W541. Reproduction recipe:

 - Get a machine with both optimus and a nvidia card with connectors
   attached to it
 - Wait for the nvidia GPU to suspend
 - Attempt to manually reprobe any of the connectors on the nvidia GPU
   using sysfs
 - *deadlock*

[airlied: use READ_ONCE to address Hans's comment]
Signed-off-by: NLyude <lyude@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Kilian Singer <kilian.singer@quantumtechnology.info>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: David Airlie <airlied@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

As it turns out, on cards that actually have CRTCs on them we're already
calling drm_kms_helper_poll_enable(drm_dev) from
nouveau_display_resume() before we call it in
nouveau_pmops_runtime_resume(). This leads us to accidentally trying to
enable polling twice, which results in a potential deadlock between the
RPM locks and drm_dev->mode_config.mutex if we end up trying to enable
polling the second time while output_poll_execute is running and holding
the mode_config lock. As such, make sure we only enable polling in
nouveau_pmops_runtime_resume() if we need to.

This fixes hangs observed on the ThinkPad W541
Signed-off-by: NLyude <lyude@redhat.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Kilian Singer <kilian.singer@quantumtechnology.info>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: David Airlie <airlied@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The original ast driver will access some BMC configuration through P2A bridge
that can be disabled since AST2300 and after.
It will cause system hanged if P2A bridge is disabled.
Here is the update to fix it.
Signed-off-by: NY.C. Chen <yc_chen@aspeedtech.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

"swiotlb buffer is full" errors occur after repeated initialisation of a
device - f.e. suspend/resume or ip link set up/down. This is because memory
mapped using dma_map_single() in ravb_ring_format() and ravb_start_xmit()
is not released.  Resolve this problem by unmapping descriptors when
freeing rings.

Fixes: c156633f ("Renesas Ethernet AVB driver proper")
Signed-off-by: NKazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
[simon: reworked]
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for allowing dsa_register_switch() to be supplied with
device/platform data, pass down a struct device pointer instead of a
struct device_node.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Accessing skb after submitting to input queue can cause
access to stale pointers if the skb ends up being transmitted
and freed by that time.
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NRaghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed that this function uses a lot of kernel stack when the
"latent entropy" plugin is enabled:

drivers/isdn/hardware/eicon/message.c: In function 'sig_ind':
drivers/isdn/hardware/eicon/message.c:6113:1: error: the frame size of 1168 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]

We currently don't warn about this, as we raise the warning limit
to 2048 bytes in mainline, but I'd like to lower that limit again
in the future, and this function can easily be changed to be more
efficient and avoid that warning, by making some of its local
variables 'const'.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch reverts commit f80de881 and avoids that sending a
WRITE SAME command to the iSCSI initiator triggers the following:

BUG: unable to handle kernel NULL pointer dereference at 0000000000000014
TARGET_CORE[iSCSI]: Expected Transfer Length: 260096 does not match SCSI CDB Length: 512 for SAM Opcode: 0x41
IP: iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]

Oops: 0000 [#1] SMP
Modules linked in: target_core_user uio target_core_iblock target_core_file iscsi_target_mod target_core_mod netconsole configfs crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 crypto_simd cryptd glue_helper virtio_console virtio_rng virtio_balloon serio_raw i2c_piix4 acpi_cpufreq button iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ext4 jbd2 mbcache virtio_blk virtio_net psmouse floppy drm_kms_helper syscopyarea
sysfillrect sysimgblt fb_sys_fops ttm drm virtio_pci
CPU: 2 PID: 5 Comm: kworker/u8:0 Not tainted 4.10.0-rc5-debug+ #3
Workqueue: iscsi_q_0 iscsi_xmitworker [libiscsi]
RIP: 0010:iscsi_tcp_segment_done+0x20b/0x310 [libiscsi_tcp]
Call Trace:
 iscsi_sw_tcp_xmit_segment+0x84/0x120 [iscsi_tcp]
 iscsi_sw_tcp_pdu_xmit+0x51/0x180 [iscsi_tcp]
 iscsi_tcp_task_xmit+0xb3/0x290 [libiscsi_tcp]
 iscsi_xmit_task+0x4e/0xc0 [libiscsi]
 iscsi_xmitworker+0x243/0x330 [libiscsi]
 process_one_work+0x1d8/0x4b0
 worker_thread+0x49/0x4a0
 kthread+0x102/0x140

Fixes: f80de881 ("sd: remove __data_len hack for WRITE SAME")
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jens Axboe <axboe@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Chris Leech <cleech@redhat.com>
Acked-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

Without this deallocate won't work properly due to the mismatch
of the bio/request size and the actual payload size.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJames Smart <james.smart@broadcom.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NSagi Grimberg <sagi@grimberg.me>

This patch performs dma sync operations on nvme_command
and nvme_completion.

nvme_command is synced
(a) on receiving of the recv queue completion for cpu access.
(b) before posting recv wqe back to rdma adapter for device access.

nvme_completion is synced
(a) on receiving of the recv queue completion of associated
nvme_command for cpu access.
(b) before posting send wqe to rdma adapter for device access.

This patch is generated for git://git.infradead.org/nvme-fabrics.git
Branch: nvmf-4.10
Signed-off-by: NParav Pandit <parav@mellanox.com>
Reviewed-by: NMax Gurtovoy <maxg@mellanox.com>