It will be SRC interrupt endless loop f unusual situation happen.
This patch adds restart limit for it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Renesas R-Car sound (= rsnd) needs 2 DMAC which are called as
Audio DMAC (= 1st DMAC) and Audio DMAC peri peri (2nd DMAC).
And rsnd had assumed that 1st / 2nd DMACs are implemented as DMAEngine.
But, in result of DMA ML discussion, 2nd DMAC was concluded that it is
not a general purpose DMAC (2nd DMAC is for Device to Device inside
sound system). Additionally, current DMAEngine can't support Device to
Device, and we don't have correct DT bindings for it at this point.
So the easiest solution for it is that move it from DMAEngine to rsnd
driver.

dma-names on DT was implemented as no difference between 1st / 2nd
DMAC's, since rsnd had assumed that both DMACs are implemented as
DMAEngine. That style was "src_dst". But now, 2nd DMAC was implemented
as non DMAEngine, and it doesn't need dma-names anymore. So, this
dma-names rule is no longer needed.

And additionally, dma-names was assumed that it has all
(= SSI/SSIU/SRC/DVC) nodes under sound node.

In upstream code, no SoC/platform is supporting DMA for rsnd driver yet.
This means there is no compatible issue if this patch changes
dma-names's rule of DT.

This patch assumes dma-names for 1st DMAC are tx/rx base, and listed
in each SSI/SRC/DVC subnode
ex)
	rcar_sound,dvc {
		dvc0: dvc@0 {
			dmas = <&audma0 0xbc>;
			dma-names = "tx";
		};
	...

	rcar_sound,src {
		src0: src@0 {
			...
			dmas = <&audma0 0x85>, <&audma1 0x9a>;
			dma-names = "rx", "tx";
		};
	...

	rcar_sound,ssi {
		ssi0: ssi@0 {
			...
			dmas = <&audma0 0x01>, <&audma1 0x02>, <&audma0 0x15>, <&audma1 0x16>;
			dma-names = "rx", "tx", "rxu", "txu";
		};
	...
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

This patch adds rsnd_src_of_node() to get SRC subnode from DT.
This is prepare for new DT bindings for 1st DMAC
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

priv is not used on rsnd_dma_quit()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_dma_available() is not used. Let's remove it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

It can get DMA direction via rsnd_dai_stream.
Remove un-needed is_play from rsnd_dma_init().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SRC/SSI output its error, but it desn't indicate
port number. it is un-understandable.
Let's indicate port number for it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver has rsnd_mod_to_priv() macro, and struct rsnd_mod
has struct rsnd_priv pointer. But, it is waste of memory from data
structure point of view.
Today we can link mod <-> io <-> rdai each other, so saving priv in
rdai is very reasonable.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver's function requests rdai, but it is not used.
Adding priv is more reasonable. Let's replace it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver's many functions requests struct rsnd_dai (= rdai),
but, 1) we can get rdai from rsnd_io_to_rsnd(), 2) almost all rdai
is not used. Let's remove these rdai.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver can use rsnd_io_to_rdai()
we can get play/capture direction via io now.
Let's replace rsnd_dai_is_play() to rsnd_io_is_play()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

struct rsnd_dai is called as "rdai", and struct snd_soc_dai is called
as "dai" on this driver. but macro/function have confusable naming.
This patch rename rsnd_dai_is_clk_master() to rsnd_rdai_is_clk_master()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current rsnd driver's mod (= ssi/src/dvc) have each own clk,
but, these are needed to start/stop each mod.
This patch adds struct clk in rsnd_mod, and start/stop these
via rsnd_mod_hw_start/stop() macro
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SRC.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_src_start/stop() requests struct rsnd_dai as parameter.
but, it is not used, and become more complex in L/R error handling.
Let's remove it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current src.c sets SRC_ROUTE_MODE0 on rsnd_src_start(), but, set it in
rsnd_src_set_convert_rate() is natural.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current src initialize SRC on rsnd_src_set_convert_rate()
but, it should be done on rsnd_src_init().
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

using many rsnd_src_convert_rate() is not readable.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current SSI doesn't care interrupt "disable" method. And, it is used
when PIO mode only at this point. SSI interrupt will be used for
sound R/L issue workaround when DMA mode too.
This patch tidyup SSI interrupt enable/disable method.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

rsnd_src_ssiu_stop() is used to stop SSIU,
but it shouldn't depend on whether it is using SSIU.
This patch stops SSIU compulsorily.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

Current Renesas R-Car sound driver debug message
is using random format
(ex "ssi0: xxx" / "SSI0 xxx" / "ssi[0]: xxx")
and confusable timing
("xxx probe failed" and "xxx probed" are shown in same time)
This patch fixes these
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@kernel.org>

R-Car sound uses Audio Local Bus which uses Lch/Rch format.
This bus is used if driver uses BUSIF.
But sound data is written as Rch/Lch format in register.
This means Rch <-> Lch will be inverted.
SSIU :: BUSIF_DALIGN is used to controlling data format.
Reported-by: NJun Watanabe <jun.watanabe.ue@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver should care more detail of SRC_BSDSR settings.
The sound includes noise without this patch
if it used SRC.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Sound data needs to be sent to R-Car sound SSI when playback.
But, there are 2 interfaces for it.
1st is SSITDR/SSIRDR which are mapped on SSI.
2nd is SSIn_BUSIF which are mapped on SSIU.

2nd SSIn_BUSIF is used when DMA transfer,
and it is always used if sound data came from via SRC.
But, we can use it when SSI+DMA case too.
(Current driver is assuming 1st SSITDR/SSIRDR for it)

2nd SSIn_BUSIF can be used as FIFO.
This is very helpful/useful for SSI+DMA.

But DMA address / DMA ID are not same between 1st/2nd cases.
This patch care about these settings.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound driver uses many modules (= SSI/SRC/DVC),
and each module had own name.
But, each module name can be used as several purpose,
like clock name, DMA name etc...
This patch uses common name for each module.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Renesas sound driver is supporting Gen1/Gen2.
SRC probe can return error if it was unknown
generation.
Now, rsnd_src_non_ops is not needed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Driver needs to call of_node_put() after of_get_chile_by_name()
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

This patch adds DVC (Digital Volume Controller)
support which is member of CMD unit.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, it can get rsnd_dai_stream pointer from rsnd_mod.
Remove duplicate parameter from rsnd_mod_ops
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

SRC module needs ADINR register settings,
but, it has many similar xxx_ADINR register,
and needs same settings.
This patch adds rsnd_get_adinr() to sharing code.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, all platform is using new style rsnd_dai_platform_info.
Keeping compatibility is no longer needed.
We can cleanup code.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

As with the previous commit, before a clock can be used it must be prepared
for use. Change from clk_enable() and clk_disable() to the versions of the
calls which also prepare and un-prepare the clocks.

Will fix warnings from the clock code when this is used.
Signed-off-by: NBen Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

src might not exist.
kernel will be hung-up without this patch in such case.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Support for loading the Renesas R-Car sound driver via DeviceTree.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

R-Car sound has SCU unit which has SRC/CTU/MIX/DVC,
and current rsnd driver has scu.c and scu module.
Current scu.c has SRC support only.
My first concept was control these feature on scu.c
but, it become difficult and un-understandable now.
This patch rename scu to src
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, rsnd_xxx_remove() do nothing.
remove these
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Now, it can use .probe
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was added.
Thus, rsnd_scu_ssi_mode_init() is called from SSI
directory by this patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current R-Car sound driver is assuming that
SCU mod is used even though it is not needed.
Because scu.c is controlling SSIU too.
(it is Gen1 compatibility)
But, SCU mod will be really not used if new platform dai
feature was used.
Thus, SSIU irq setting is called from SSI
directory by this patch.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>

Current rsnd driver is assuming that SCU/SRU ID is
same as SSIU/SSI ID, because Gen1 can't select it.
But, Gen2 can select it.
The SCU/SRU/SSIU/SSI pair depends on the platform.
This patch get correct SCU ID from platform info.
To keep compatible, it still assuming SCU ID = SSI ID
if platform doesn't have info
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NMark Brown <broonie@linaro.org>