- 11 12月, 2009 1 次提交
-
-
由 Arnd Bergmann 提交于
Half the compat_ioctl handling is in devio.c, the other half is in fs/compat_ioctl.c. This moves everything into one place for consistency. As a positive side-effect, push down the BKL into the ioctl methods. Signed-off-by: NArnd Bergmann <arnd@arndb.de> Acked-by: NGreg Kroah-Hartman <gregkh@suse.de> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: Oliver Neukum <oliver@neukum.org> Cc: Alon Bar-Lev <alon.barlev@gmail.com> Cc: David Vrabel <david.vrabel@csr.com> Cc: linux-usb@vger.kernel.org
-
- 04 12月, 2009 2 次提交
-
-
由 André Goddard Rosa 提交于
That is "success", "unknown", "through", "performance", "[re|un]mapping" , "access", "default", "reasonable", "[con]currently", "temperature" , "channel", "[un]used", "application", "example","hierarchy", "therefore" , "[over|under]flow", "contiguous", "threshold", "enough" and others. Signed-off-by: NAndré Goddard Rosa <andre.goddard@gmail.com> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
由 Ozan Çağlayan 提交于
The correct word is handshake. Signed-off-by: NOzan Çağlayan <ozan@pardus.org.tr> Signed-off-by: NJiri Kosina <jkosina@suse.cz>
-
- 01 12月, 2009 10 次提交
-
-
由 Gernot Hillier 提交于
This patch adds the vendor and device id for the Mobilcom Debitel UMTS surf stick (a.k.a. 4G Systems XSStick W14, MobiData MBD-200HU, ...). To see these ids, you need to switch the stick to modem operation first with the help of usb_modeswitch. This makes it switch from 1c9e:f000 to 1c9e:9603 and thus be recognized by the option driver. Signed-off-by: NGernot Hillier <gernot@hillier.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
a quirky chipset needs periodic schedules to run for a minimum time before they can be disabled again. This enforces the requirement with a time stamp and a calculated delay Signed-off-by: NOliver Neukum <oliver@neukum.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Daniel Glöckner 提交于
On tx channel abort a cppi interrupt is generated for a short time by setting the lowest bit of the TCPPICOMPPTR register. It is then reset immediately by clearing the bit. When the interrupt handler is run, it does not detect an interrupt in the TCPPIMSKSR or RCPPIMSKSR registers and thus exits early without writing the TCPPIEOIR register. It appears that this inhibits further cppi interrupts until the handler is called by chance, f.ex. from davinci_interrupt(). By moving the unmasking of the interrupt below the writes to TCPPICOMPPTR, no interrupt is generated and no write to TCPPIEOIR is necessary. Signed-off-by: NDaniel Glöckner <dg@emlix.com> Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Daniel Glöckner 提交于
In gadget mode the answer to a control request should be followed by a zero-length packet if the amount transferred is an exact multiple of the endpoint's packet size and the requests has its "zero" flag set. This patch prevents the request from being immediately removed from the queue when a control IN transfer ends on a full packet and "zero" is set. The next time ep0_txstate is entered, a zero-length packet is queued and the request is removed as fifo_count is 0. Signed-off-by: NDaniel Glöckner <dg@emlix.com> Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
Isochronous Tx DMA is getting programmed but never getting started for CPPI and TUSB DMAs and thus Isochronous Tx doesn't work. Fixing it by starting DMAs using musb_h_tx_dma_start(). Signed-off-by: NSwaminathan S <swami.iyer@ti.com> Signed-off-by: NBabu Ravi <ravibabu@ti.com> Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
Removes below unnecessary log of almost 28 lines during boot. musb_hdrc: hw_ep 0shared, max 64 musb_hdrc: hw_ep 1tx, max 512 musb_hdrc: hw_ep 1rx, max 512 ... ... musb_hdrc: hw_ep 13shared, max 4096 musb_hdrc: hw_ep 14shared, max 1024 musb_hdrc: hw_ep 15shared, max 1024 Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Acked-by: NFelipe Balbi <felipe.balbi@nokia.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Thomas Dahlmann 提交于
- fixed shared interrupt bug reported by Vadim Lobanov - fixed possible warning oops on driver unload when connected - prevent interrupt flood in PIO mode ("modprobe amd5536udc use_dma=0") when using gadget ether Signed-off-by: NThomas Dahlmann <dahlmann.thomas@arcor.de> Cc: Robert Richter <robert.richter@amd.com> Cc: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Eric W. Biederman 提交于
The use of urb->actual_length to update tx_outstanding_bytes implicitly assumes that the number of bytes actually written is the same as the number of bytes we tried to write. On error that assumption is violated so just use transfer_buffer_length the number of bytes we intended to write to the device. If an error occurs we need to fall through and call usb_serial_port_softint to wake up processes waiting in tty_wait_until_sent. Signed-off-by: NEric W. Biederman <ebiederm@aristanetworks.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
The driver incorrectly cancels the mass-storage device CSW request (which leads to device reset) due to giving back URB at the head of endpoint's queue after sending each STALL handshake; stop doing that and start checking for the queue being non-empty before stalling an endpoint and disallowing stall in such case in musb_gadget_set_halt() like the other gadget drivers do. Moreover, the driver starts Rx request despite of the endpoint being halted -- fix this by moving the SendStall bit check from musb_g_rx() to rxstate(). And we also sometimes get into rxstate() with DMA still active after clearing an endpoint's halt (not clear why), so bail out in this case, similarly to what txstate() does... While at it, also do the following changes : - in musb_gadget_set_halt(), remove pointless Tx FIFO flushing (the driver does not allow stalling with non-empty Tx FIFO anyway); - in rxstate(), stop pointlessly zeroing the 'csr' variable; - in musb_gadget_set_halt(), move the 'done' label to a more proper place; - in musb_g_rx(), eliminate the 'done' label completely... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Cc: <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1304) fixes a regression in ehci-hcd. Evidently some hubs don't handle Clear-TT-Buffer requests correctly, so we should avoid sending them when they don't appear to be absolutely necessary. The reported symptom is that output on a downstream audio device cuts out because the hub stops relaying isochronous packets. The patch prevents Clear-TT-Buffer requests from being sent following a STALL handshake. In theory a STALL indicates either that the downstream device sent a STALL or that no matching TT buffer could be found. In either case, the transfer is completed and the TT buffer does not remain busy, so it doesn't need to be cleared. Also, the patch fixes a minor flaw in the code that actually sends the Clear-TT-Buffer requests. Although the pipe direction isn't really used for control transfers, it should be a Send rather than a Receive. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Reported-by: NJavier Kohen <jkohen@users.sourceforge.net> CC: David Brownell <david-b@pacbell.net> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 29 11月, 2009 2 次提交
-
-
由 Dominik Brodowski 提交于
Most of the irq_req_t typedef'd struct can be re-worked quite easily: (1) IRQInfo2 was unused in any case, so drop it. (2) IRQInfo1 was used write-only, so drop it. (3) Instance (private data to be passed to the IRQ handler): Most PCMCIA drivers using pcmcia_request_irq() to actually register an IRQ handler set the "dev_id" to the same pointer as the "priv" pointer in struct pcmcia_device. Modify the two exceptions (ipwireless, ibmtr_cs) to also work this waym and set the IRQ handler's "dev_id" to p_dev->priv unconditionally. (4) Handler is to be of type irq_handler_t. (5) Handler != NULL already tells whether an IRQ handler is present. Therefore, we do not need the IRQ_HANDLER_PRESENT flag in irq_req_t.Attributes. CC: netdev@vger.kernel.org CC: linux-bluetooth@vger.kernel.org CC: linux-ide@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: linux-scsi@vger.kernel.org CC: alsa-devel@alsa-project.org CC: Jaroslav Kysela <perex@perex.cz> CC: Jiri Kosina <jkosina@suse.cz> CC: Karsten Keil <isdn@linux-pingi.de> for the Bluetooth parts: Acked-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
-
由 Dominik Brodowski 提交于
Update remaining users and remove deprecated handle_to_dev() macro CC: Harald Welte <laforge@gnumonks.org> CC: netdev@vger.kernel.org CC: linux-wireless@vger.kernel.org CC: linux-serial@vger.kernel.org Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
-
- 23 11月, 2009 1 次提交
-
-
由 Cory Maccarrone 提交于
The l3_ocpi_ck clock is needed on omap7xx processors for USB. Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for the usb_dc_ck on omap7xx, which is a different bit than that of the omap16xx-defined clock of the same name. I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as dc_clk and hhc_clk, respectively, for omap7xx CPUs. Additionally, I added a check in machine_without_vbus_sense for all omap7xx devices, as presently I know of no omap7xx-based devices that have vbus sense, and it made more sense to me to use a cpu check here than to spell out each machine one at a time. Finally, DMA is disabled for omap7xx, as it causes problems with these chips. Cc: linux-usb@vger.kernel.org Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com> Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 18 11月, 2009 9 次提交
-
-
由 Zhang Le 提交于
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device has 4 interfaces, of which 1 is handled by storage and the other 3 by option driver. The device appears first as CD-only 05c6:2100 device and must be switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch. The MessageContent for usb_modeswitch.conf is: "55534243e0c26a85000000000000061b000000020000000000000000000000" Signed-off-by: NZhang Le <r0bertz@gentoo.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
This patch (as1299b) fixes a bug in an error-handling path of usbmon's binary interface. The storage area for URB data is divided into fixed-size blocks. If an URB's data can't be copied, the area reserved for it should be decreased to the size of the truncated information (rounded up to a block boundary). Rounding up the amount to be removed and subtracting it from the reserved size is definitely the wrong thing to do. Also, when the data for an isochronous URB can't be copied, we can still copy the isoc packet descriptors. In fact the current code does copy the descriptors, but then sets the capture length to 0 so they remain inaccessible. The capture length should be reduced to the length of the descriptors, not set to 0. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Acked-by: NPete Zaitcev <zaitcev@redhat.com> CC: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sarah Sharp 提交于
The scratchpad_free() function uses xhci->page_size to free some memory with pci_free_consistent(). However, the page_size is set to zero before the call, causing kernel oopses on driver unload. Call scratchpad_free() before setting xhci->page_size to zero. Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Acked-by: NJohn Youn <John.Youn@synopsys.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sarah Sharp 提交于
The trb_in_td() function in the xHCI driver is supposed to translate a physical transfer buffer request (TRB) into a virtual pointer to the ring segment that TRB is in. Unfortunately, a mistake in this function may cause endless loops as the driver searches through the linked list of ring segments over and over again. Fix a couple bugs that may lead to loops or bad output: 1. Bail out if we get a NULL pointer when translating the segment's private structure and the starting DMA address of the segment chunk. If this happens, we've been handed a starting TRB pointer from a different ring. 2. Make sure the function works when there's multiple segments in the ring. In the while loop to search through the ring segments, use the current segment variable (cur_seg), rather than the starting segment variable (start_seg) that is passed in. 3. Stop searching the ring if we've run through all the segments in the ring. Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sarah Sharp 提交于
If the xHCI driver fails during the memory initialization, xhci->ir_set may not be a valid pointer. Check that it points to valid DMA'able memory before writing to that address during the memory freeing process. Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Francesco Lavra 提交于
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich: > Hello, > > i have the following problem with the cdc-acm - driver: > > I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400. > > If a disable the device (with the RFKill-Switch) while it is used by a > programm like ppp, the driver doesn't seem to correctly clean up the tty, > even after the program has been closed) > > The tty is still active (e.g. there still exists an entry in > /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device, > this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2 > and ttyACM3 will be used. > > This problem was introduced with the commit > 10077d4a (before 2.6.31-rc1) and still > exists in 2.6.31. > > I was able the fix this problem with the following patch: > > diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c > index 2bfc41e..0970d2f 100644 > --- a/drivers/usb/class/cdc-acm.c > +++ b/drivers/usb/class/cdc-acm.c > @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty) > struct acm *acm = tty->driver_data; > tty_port_hangup(&acm->port); > acm_port_down(acm, 0); > + acm_tty_unregister(acm); > } I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I unplug it from the USB port during a PPP connection, the ppp daemon gets the hangup correctly (and closes the device), but the struct acm corresponding to the device disconnected is not freed. Hence reconnecting the device results in creation of /dev/ttyACM(x+1). The same happens when the system is hibernated during a PPP connection. This memory leak is due to the fact that when the tty is hung up, tty_port_close_start() returns always zero, and acm_tty_close() never reaches the point where acm_tty_unregister() is called. Here is a fix for this. Signed-off-by: NFrancesco Lavra <francescolavra@interfree.it> Acked-by: NOliver Neukum <oliver@neukum.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Henry Gebhardt 提交于
If acm_rx_tasklet() gets called before tty_port_block_til_ready() returns, then bulk IN urbs may not be sent. This fixes it. Signed-off-by: NHenry Gebhardt <gebhardt@astro.uni-tuebingen.de> Acked-by: NOliver Neukum <oliver@neukum.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Libin Yang 提交于
The following patch in the driver is required to avoid USB 1.1 device failures that may occur due to requests from USB OHCI controllers may be overwritten if the latency for any pending request by the USB controller is very long (in the range of milliseconds). Signed-off-by: NLibin Yang <libin.yang@amd.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Cox 提交于
Original discussion: http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248 or http://marc.info/?l=linux-usb&m=125553790714133&w=2 9a68e39d broke carrier handling so that a cp210x setup which needed the carrier lines set up (non CLOCAL) which did not make a call which set the termios bits left the lines down even if CLOCAL was not asserted. Fix this not by reverting but by adding the proper dtr_rts and carrier_raised methods. This both sets the modem lines properly and also implements the correct blocking semantics for the port as required by POSIX. Signed-off-by: NAlan Cox <alan@linux.intel.com> Reported-by: NKarl Hiramoto <karl@hiramoto.org> Tested-by: NKarl Hiramoto <karl@hiramoto.org> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 09 11月, 2009 1 次提交
-
-
由 Dominik Brodowski 提交于
Convert PCMCIA drivers to use the dynamic debug infrastructure, instead of requiring manual settings of PCMCIA_DEBUG. Also, remove all usages of the CS_CHECK macro and replace them with proper Linux style calling and return value checking. The extra error reporting may be dropped, as the PCMCIA core already complains about any (non-driver-author) errors. CC: linux-mtd@lists.infradead.org CC: linux-usb@vger.kernel.org Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>
-
- 31 10月, 2009 5 次提交
-
-
由 Anton Vorontsov 提交于
fsl_udc_release() calls dma_free_coherent() with an inappropriate device passed to it, and since the device has no dma_ops, the following oops pops up: Kernel BUG at d103ce9c [verbose debug info unavailable] Oops: Exception in kernel mode, sig: 5 [#1] ... NIP [d103ce9c] fsl_udc_release+0x50/0x80 [fsl_usb2_udc] LR [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc] Call Trace: [cfbc7dc0] [d103ce74] fsl_udc_release+0x28/0x80 [fsl_usb2_udc] [cfbc7dd0] [c01a35c4] device_release+0x2c/0x90 [cfbc7de0] [c016b480] kobject_cleanup+0x58/0x98 [cfbc7e00] [c016c52c] kref_put+0x54/0x6c [cfbc7e10] [c016b360] kobject_put+0x34/0x64 [cfbc7e20] [c01a1d0c] put_device+0x1c/0x2c [cfbc7e30] [d103dbfc] fsl_udc_remove+0xc0/0x1e4 [fsl_usb2_udc] ... This patch fixes the issue by passing dev->parent, which points to a correct device. Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com> Cc: Li Yang <leoli@freescale.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Guennadi Liakhovetski <lg@denx.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Bryan Wu 提交于
Add ID for Tlaytech TUE800 CDMA modem to the option driver. Signed-off-by: NBryan Wu <bryan.wu@canonical.com> Acked-By: NMatthias Urlichs <matthias@urlichs.de> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Yoshihiro Shimoda 提交于
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Elina Pasheva 提交于
This patch presents fixes for the autosuspend feature implementation in sierra usb serial driver in functions sierra_open(), sierra_close() and stop_read_write_urbs(). The patch "sierra_close() must resume the device before it notifies it of a closure" submitted by Oliver Neukum on Wed, October 14 has been merged as fix in sierra_close() function. The bug fix in sierra_open() function restores the autopm interface state on error condition. The bug fix in in stop_read_write_urbs() function assures that both receive and interrupt urbs are recycled. Signed-off-by: NElina Pasheva <epasheva@sierrawireless.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Elina Pasheva 提交于
This patch presents a fix for the autosuspend feature implementation in sierra usb serial driver for function sierra_send_setup(). Because it is possible to call sierra_send_setup() before sierra_open() or after sierra_close() we added a get/put interface activity to assure that the usb control can happen even when the device is autosuspended. Signed-off-by: NElina Pasheva <epasheva@sierrawireless.com> Tested-by: NMatthew Safar <msafar@sierrawireless.com> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 21 10月, 2009 2 次提交
-
-
由 Russell King 提交于
drivers/built-in.o: In function `pxa25x_udc_probe': drivers/usb/gadget/pxa25x_udc.c:2195: undefined reference to `otg_get_transceiver' drivers/usb/gadget/pxa25x_udc.c:2300: undefined reference to `otg_put_transceiver' pxa25x_udc.c unconditionally uses these two functions, so we need to ensure that the object providing them is also built. Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
-
由 Tony Lindgren 提交于
Move the remaining headers under plat-omap/include/mach to plat-omap/include/plat. Also search and replace the files using these headers to include using the right path. This was done with: #!/bin/bash mach_dir_old="arch/arm/plat-omap/include/mach" plat_dir_new="arch/arm/plat-omap/include/plat" headers=$(cd $mach_dir_old && ls *.h) omap_dirs="arch/arm/*omap*/ \ drivers/video/omap \ sound/soc/omap" other_files="drivers/leds/leds-ams-delta.c \ drivers/mfd/menelaus.c \ drivers/mfd/twl4030-core.c \ drivers/mtd/nand/ams-delta.c" for header in $headers; do old="#include <mach\/$header" new="#include <plat\/$header" for dir in $omap_dirs; do find $dir -type f -name \*.[chS] | \ xargs sed -i "s/$old/$new/" done find drivers/ -type f -name \*omap*.[chS] | \ xargs sed -i "s/$old/$new/" for file in $other_files; do sed -i "s/$old/$new/" $file done done for header in $(ls $mach_dir_old/*.h); do git mv $header $plat_dir_new/ done Signed-off-by: NTony Lindgren <tony@atomide.com>
-
- 15 10月, 2009 7 次提交
-
-
由 Brian Niebuhr 提交于
Remove expository comments and fix USB VID and PID Signed-off-by: NBrian Niebuhr <bniebuhr@efjohnson.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Benjamin Herrenschmidt 提交于
usb-storage: Workaround devices with bogus sense size Some devices, such as Huawei E169, advertise more than the standard amount of sense data, causing us to set US_FL_SANE_SENSE, assuming they support it. However, they subsequently fail the request sense with that size. This works around it generically. When a sense request fails due to a device returning an error, US_FL_SANE_SENSE was set, and that sense request used a larger sense size, we retry with a smaller size before giving up. Based on an original patch by Ben Efros <ben@pc-doctor.com> Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sarah Sharp 提交于
When the EHCI driver falls behind in its scheduling, the active stream's first empty microframe may be in the past with respect to the current microframe. The code attempts to move the starting microframe ("start") N number of microframes forward, where N is the interval of endpoint. However, stream->interval is a copy of the endpoint's bInterval, which is designated in frames for FS devices, and microframes for HS devices. Convert stream->interval to microframes before using it to move the starting microframe forward. Acked-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Huzaifa Sidhpurwala 提交于
Here is a patch for Airplus MCD 650 card Note: This device is with Victor V Kudlak, and he confirmed that this device works with the patch. Signed-off-by: NHuzaifa Sidhpurwala <sidhpurwala.huzaifa@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Vrabel 提交于
A halted qTD always triggers a hardware list update because the qset was either removed or reactivated. Signed-off-by: NDavid Vrabel <david.vrabel@csr.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 David Vrabel 提交于
If an endpoint is deleted before it's been fully added to the hardware list, the associated qset will not be fully initialized and an oops will occur when complete(&qset->remove_complete) is called. This can happen if a queued URB is cancelled. Fix this by only removing the qset from the hardware list if the cancelled URB had qTDs. Signed-off-by: NDavid Vrabel <david.vrabel@csr.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Stefano Panella 提交于
An urb's transfer buffer must be kmalloc'd memory and not point to the stack or a DMA API warning results. Signed-off-by: NDavid Vrabel <david.vrabel@csr.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-