The HDMI controller cannot go above a certain pixel rate limit depending on
the generations, but that limit is only enforced in mode_valid at the
moment, which means that we won't advertise modes that exceed that limit,
but the userspace is still free to try to setup a mode that would.

Implement atomic_check to make sure we check it in that scenario too.
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NDave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029122522.1917579-1-maxime@cerno.tech

Commit e0d07278 ("dma-mapping: introduce DMA range map, supplanting
dma_pfn_offset") introduced a regression in our code since the second
backed to probe will now get -EINVAL back from dma_direct_set_offset and
will prevent the entire DRM device from probing.

Ignore -EINVAL as a temporary measure to get it back working, before
removing that call entirely.

Fixes: e0d07278 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Fix to return a negative error code from the error handling case instead
of 0 in function sun8i_dw_hdmi_bind().

Fixes: b7c7436a ("drm/sun4i: Implement A83T HDMI driver")
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NXiongfeng Wang <wangxiongfeng2@huawei.com>
Reviewed-by: NJernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: NJernej Skrabec <jernej.skrabec@siol.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1605488969-5211-1-git-send-email-wangxiongfeng2@huawei.com

It has been observed that resetting force in the detect function can
result in the PHY being powered down in response to hot-plug detect
being asserted, even when the HDMI connector is forced on.

Enabling debug messages and adding a call to dump_stack() in
dw_hdmi_phy_power_off() shows the following in dmesg:
[  160.637413] dwhdmi-rockchip ff940000.hdmi: EVENT=plugin
[  160.637433] dwhdmi-rockchip ff940000.hdmi: PHY powered down in 0 iterations

Call trace:
dw_hdmi_phy_power_off
dw_hdmi_phy_disable
dw_hdmi_update_power
dw_hdmi_detect
dw_hdmi_connector_detect
drm_helper_probe_detect_ctx
drm_helper_hpd_irq_event
dw_hdmi_irq
irq_thread_fn
irq_thread
kthread
ret_from_fork

Fixes: 381f05a7 ("drm: bridge/dw_hdmi: add connector mode forcing")
Signed-off-by: NJonathan Liu <net147@gmail.com>
Reviewed-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201031081747.372599-1-net147@gmail.com

Since we now turn off the EPOD regulator to reset the
hardware, we need to balance the regulators after that
point. If registering the master fails we only need
to disable one regulator. Fix this by open-coding
this leg of the error path.

Fixes: c4842d4d ("drm/mcde: Fix display pipeline restart")
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Reviewed-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Stephan Gerhold <stephan@gerhold.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20201108113535.1819952-1-linus.walleij@linaro.org

The gma500 driver expects 3 pipelines in several it's IRQ functions.
Accessing struct drm_device.vblank[], this fails with devices that only
have 2 pipelines. An example KASAN report is shown below.

  [   62.267688] ==================================================================
  [   62.268856] BUG: KASAN: slab-out-of-bounds in psb_irq_postinstall+0x250/0x3c0 [gma500_gfx]
  [   62.269450] Read of size 1 at addr ffff8880012bc6d0 by task systemd-udevd/285
  [   62.269949]
  [   62.270192] CPU: 0 PID: 285 Comm: systemd-udevd Tainted: G            E     5.10.0-rc1-1-default+ #572
  [   62.270807] Hardware name:  /DN2800MT, BIOS MTCDT10N.86A.0164.2012.1213.1024 12/13/2012
  [   62.271366] Call Trace:
  [   62.271705]  dump_stack+0xae/0xe5
  [   62.272180]  print_address_description.constprop.0+0x17/0xf0
  [   62.272987]  ? psb_irq_postinstall+0x250/0x3c0 [gma500_gfx]
  [   62.273474]  __kasan_report.cold+0x20/0x38
  [   62.273989]  ? psb_irq_postinstall+0x250/0x3c0 [gma500_gfx]
  [   62.274460]  kasan_report+0x3a/0x50
  [   62.274891]  psb_irq_postinstall+0x250/0x3c0 [gma500_gfx]
  [   62.275380]  drm_irq_install+0x131/0x1f0
  <...>
  [   62.300751] Allocated by task 285:
  [   62.301223]  kasan_save_stack+0x1b/0x40
  [   62.301731]  __kasan_kmalloc.constprop.0+0xbf/0xd0
  [   62.302293]  drmm_kmalloc+0x55/0x100
  [   62.302773]  drm_vblank_init+0x77/0x210

Resolve the issue by only handling vblank entries up to the number of
CRTCs.

I'm adding a Fixes tag for reference, although the bug has been present
since the driver's initial commit.
Signed-off-by: NThomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Fixes: 5c49fd3a ("gma500: Add the core DRM files and headers")
Cc: Alan Cox <alan@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Cc: dri-devel@lists.freedesktop.org
Cc: stable@vger.kernel.org#v3.3+
Link: https://patchwork.freedesktop.org/patch/msgid/20201105190256.3893-1-tzimmermann@suse.de

With the integration of chip-id detection scheme in kernel[1], there
is no specific need to maintain multitudes of SoC specific config
options, discussed as per [2], we have deprecated the usage in other
places for v5.10-rc1. Fix the missing user so that we can clean up the
configs in v5.11.

[1] drivers/soc/ti/k3-socinfo.c commit 907a2b7e ("soc: ti: add k3 platforms chipid module driver")
[2] https://lore.kernel.org/linux-arm-kernel/20200908112534.t5bgrjf7y3a6l2ss@akan/

Fixes: afba7e6c ("drm: bridge: cdns-mhdp8546: Add TI J721E wrapper")
Cc: Swapnil Jakhade <sjakhade@cadence.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Yuti Amonkar <yamonkar@cadence.com>
Cc: Jyri Sarha <jsarha@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20201026165441.22894-1-nm@ti.com

The commit dcda7c28 ("drm/vc4: kms: Add functions to create the state
objects") removed the last users of the vc4 variable, but didn't remove
that variable resulting in a warning.

Fixes: dcda7c28 ("drm/vc4: kms: Add functions to create the state objects")
Reported-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201102162908.1436567-1-maxime@cerno.tech

When unloading the call to pm_runtime_put_sync_suspend() will attempt to
turn the GPU cores off, however panfrost_device_fini() will have turned
the clocks off. This leads to the hardware locking up.

Instead don't call pm_runtime_put_sync_suspend() and instead simply mark
the device as suspended using pm_runtime_set_suspended(). And also
include this on the error path in panfrost_probe().

Fixes: aebe8c22 ("drm/panfrost: Fix possible suspend in panfrost_remove")
Signed-off-by: NSteven Price <steven.price@arm.com>
Reviewed-by: NTomeu Vizoso <tomeu.vizoso@collabora.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201030145833.29006-1-steven.price@arm.com

panfrost_ioctl_madvise() and panfrost_gem_purge() acquire the mappings
and shmem locks in different orders, thus leading to a potential
the mappings lock first.

Fixes: bdefca2d ("drm/panfrost: Add the panfrost_gem_mapping concept")
Cc: <stable@vger.kernel.org>
Cc: Christian Hewitt <christianshewitt@gmail.com>
Reported-by: NChristian Hewitt <christianshewitt@gmail.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: NSteven Price <steven.price@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201101174016.839110-1-boris.brezillon@collabora.com

In order to make the vc4_kms_load code and error path a bit easier to
read and extend, add functions to create state objects, and use managed
actions to cleanup if needed.
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-6-maxime@cerno.tech

We can simplify a bit the bind code, its error path and unbind by using
the managed devm_drm_dev_alloc function.
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-5-maxime@cerno.tech

We have a helper to retrieve the vc4_dev structure from the drm_device one
when needed, so let's use it consistently.
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-4-maxime@cerno.tech

The job queue needs to be cleaned up using vc4_gem_destroy, but it's
not used consistently (vc4_drv's bind calls it in its error path, but
doesn't in unbind), and we can make that automatic through a managed
action. Let's remove the requirement to call vc4_gem_destroy.

Fixes: d5b1a78a ("drm/vc4: Add support for drawing 3D frames.")
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-3-maxime@cerno.tech

Using drmm_mode_config_init instead of drm_mode_config_init allows us to
cleanup a bit the error path.
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-2-maxime@cerno.tech

The BO cache needs to be cleaned up using vc4_bo_cache_destroy, but it's
not used consistently (vc4_drv's bind calls it in its error path, but
doesn't in unbind), and we can make that automatic through a managed
action. Let's remove the requirement to call vc4_bo_cache_destroy.

Fixes: c826a6e1 ("drm/vc4: Add a BO cache.")
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201029190104.2181730-1-maxime@cerno.tech

While I thought I had this correct (since it actually did reject modes
like I expected during testing), Ville Syrjala from Intel pointed out
that the logic here isn't correct. max_clock refers to the max data rate
supported by the DP encoder. So, limiting it to the output of ds_clock (which
refers to the maximum dotclock of the downstream DP device) doesn't make any
sense. Additionally, since we're using the connector's bpc as the canonical BPC
we should use this in mode_valid until we support dynamically setting the bpp
based on bandwidth constraints.

https://lists.freedesktop.org/archives/dri-devel/2020-September/280276.html

For more info.

So, let's rewrite this using Ville's advice.

v2:
* Ville pointed out I mixed up the dotclock and the link rate. So fix that...
* ...and also rename all the variables in this function to be more appropriately
  labeled so I stop mixing them up.
* Reuse the bpp from the connector for now until we have dynamic bpp selection.
* Use use DIV_ROUND_UP for calculating the mode rate like i915 does, which we
  should also have been doing from the start
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: 409d3813 ("drm/nouveau/kms/nv50-: Use downstream DP clock limits for mode validation")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Ville also pointed out that I got a lot of the logic here wrong as well, whoops.
While I don't think anyone's likely using 3D output with nouveau, the next patch
will make nouveau_conn_mode_valid() make a lot less sense. So, let's just get
rid of it and open-code it like before, while taking care to move the 3D frame
packing calculations on the dot clock into the right place.
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: d6a9efec ("drm/nouveau/kms/nv50-: Share DP SST mode_valid() handling with MST")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

With this we try to detect if the endianess switch works and assume LE if
not. Suggested by Ben.

Fixes: 51c05340 ("drm/nouveau/device: detect if changing endianness failed")
Signed-off-by: NKarol Herbst <kherbst@redhat.com>
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

we can't use nouveau_bo_ref here as no ttm object was allocated and
nouveau_bo_ref mainly deals with that. Simply deallocate the object.
Signed-off-by: NKarol Herbst <kherbst@redhat.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Not entirely sure why this never came up when I originally tested this
(maybe some BIOSes already have this setup?) but the ->caps_init vfunc
appears to cause the display engine to throw an exception on driver
init, at least on my ThinkPad P72:

nouveau 0000:01:00.0: disp: chid 0 mthd 008c data 00000000 0000508c 0000102b

This is magic nvidia speak for "You need to have the DMA notifier offset
programmed before you can call NV507D_GET_CAPABILITIES." So, let's fix
this by doing that, and also perform an update afterwards to prevent
racing with the GPU when reading capabilities.

v2:
* Don't just program the DMA notifier offset, make sure to actually
  perform an update
v3:
* Don't call UPDATE()
* Actually read the correct notifier fields, as apparently the
  CAPABILITIES_DONE field lives in a different location than the main
  NV_DISP_CORE_NOTIFIER_1 field. As well, 907d+ use a different
  CAPABILITIES_DONE field then pre-907d cards.
v4:
* Don't forget to check the return value of core507d_read_caps()
v5:
* Get rid of NV50_DISP_CAPS_NTFY[14], use NV50_DISP_CORE_NTFY
* Disable notifier after calling GetCapabilities()
Signed-off-by: NLyude Paul <lyude@redhat.com>
Fixes: 4a2cb418 ("drm/nouveau/kms/nv50-: Probe SOR and PIOR caps for DP interlacing support")
Cc: <stable@vger.kernel.org> # v5.8+
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

The user level OpenCL code shouldn't have to align start and end
addresses to a page boundary. That is better handled in the nouveau
driver. The npages field is also redundant since it can be computed
from the start and end addresses.
Signed-off-by: NRalph Campbell <rcampbell@nvidia.com>
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We don't currently handle the initial fb readout correctly
for 90/270 degree rotated scanout. Reject it.

Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201020194330.28568-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit a40a8305)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Restore RPS for ILK-M. We lost it when an extra HAS_RPS()
check appeared in intel_rps_enable().

Unfortunaltey this just makes the performance worse on my
ILK because intel_ips insists on limiting the GPU freq to
the minimum. If we don't do the RPS init then intel_ips will
not limit the frequency for whatever reason. Either it can't
get at some required information and thus makes wrong decisions,
or we mess up some weights/etc. and cause it to make the wrong
decisions when RPS init has been done, or the entire thing is
just wrong. Would require a bunch of reverse engineering to
figure out what's going on.

Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 9c878557 ("drm/i915/gt: Use the RPM config register to determine clk frequencies")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021131443.25616-1-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 2bf06370)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

We are incorrectly limiting the max allocation size as per the mm
max_order, which is effectively the largest power-of-two that we can fit
in the region size. However, it's normal to setup the region or
allocator with a non-power-of-two size(for example 3G), which we should
already handle correctly, except it seems for the early too-big-check.

v2: make sure we also exercise the I915_BO_ALLOC_CONTIGUOUS path, which
is quite different, since for that we are actually limited by the
largest power-of-two that we can fit within the region size. (Chris)

Fixes: b908be54 ("drm/i915: support creating LMEM objects")
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201021103606.241395-1-matthew.auld@intel.com
(cherry picked from commit 83ebef47)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Most of the helpers to retrieve vc4 structures from the DRM base structures
rely on the fact that the first member of the vc4 structure is the DRM one
and just cast the pointers between them.

However, this is pretty fragile especially since there's no check to make
sure that the DRM structure is indeed at the offset 0 in the structure, so
let's use container_of to make it more robust.
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NDave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201028123752.1733242-1-maxime@cerno.tech

Since the components for a given device in ASoC are identified by their
name, it makes sense to add one even though it's not strictly necessary.
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NDave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200708144555.718404-1-maxime@cerno.tech

When we forward an mmap to the dma_buf exporter, they get to own
everything. Unfortunately drm_gem_mmap_obj() overwrote
vma->vm_private_data after the driver callback, wreaking the
exporter complete. This was noticed because vb2_common_vm_close blew
up on mali gpu with panfrost after commit 26d3ac3c
("drm/shmem-helpers: Redirect mmap for imported dma-buf").

Unfortunately drm_gem_mmap_obj also acquires a surplus reference that
we need to drop in shmem helpers, which is a bit of a mislayer
situation. Maybe the entire dma_buf_mmap forwarding should be pulled
into core gem code.

Note that the only two other drivers which forward mmap in their own
code (etnaviv and exynos) get this somewhat right by overwriting the
gem mmap code. But they seem to still have the leak. This might be a
good excuse to move these drivers over to shmem helpers completely.
Reviewed-by: NBoris Brezillon <boris.brezillon@collabora.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Russell King <linux+etnaviv@armlinux.org.uk>
Cc: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Inki Dae <inki.dae@samsung.com>
Cc: Joonyoung Shim <jy0922.shim@samsung.com>
Cc: Seung-Woo Kim <sw0312.kim@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Fixes: 26d3ac3c ("drm/shmem-helpers: Redirect mmap for imported dma-buf")
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Rob Herring <robh@kernel.org>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-media@vger.kernel.org
Cc: linaro-mm-sig@lists.linaro.org
Cc: <stable@vger.kernel.org> # v5.9+
Reported-and-tested-by: piotr.oniszczuk@gmail.com
Cc: piotr.oniszczuk@gmail.com
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027214922.3566743-1-daniel.vetter@ffwll.ch

When running the trigger hook, ALSA by default will take a spinlock, and
thus will run the trigger hook in atomic context.

However, our HDMI driver will send the infoframes as part of the trigger
hook, and part of that process is to wait for a bit to be cleared for up to
100ms. To be nicer to the system, that wait has some usleep_range that
interact poorly with the atomic context.

There's several ways we can fix this, but the more obvious one is to make
ALSA take a mutex instead by setting the nonatomic flag on the DAI link.
That doesn't work though, since now the cyclic callback installed by the
dmaengine helpers in ALSA will take a mutex, while that callback is run by
dmaengine's virt-chan code in a tasklet where sleeping is not allowed
either.

Given the delay we need to poll the bit for, changing the usleep_range for
a udelay and keep running it from a context where interrupts are disabled
is not really a good option either.

However, we can move the infoframe setup code in the hw_params hook, like
is usually done in other HDMI controllers, that isn't protected by a
spinlock and thus where we can sleep. Infoframes will be sent on a regular
basis anyway, and since hw_params is where the audio parameters that end up
in the infoframes are setup, this also makes a bit more sense.

Fixes: bb7d7856 ("drm/vc4: Add HDMI audio support")
Suggested-by: NMark Brown <broonie@kernel.org>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Reviewed-by: NMark Brown <broonie@kernel.org>
Reviewed-by: NTakashi Iwai <tiwai@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027101558.427256-1-maxime@cerno.tech

It has been confirmed that the SMU metrics table should always reflect
the current fan speed even in manual mode.

Fixes: 3033e9f1c2de ("drm/amdgpu/swsmu: handle manual fan readback on SMU11")
Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

fix the wrong fan speed in fan1_input when the fan control mode is manual.
the fan speed value is not correct when we set manual mode to fan1_enalbe - 1.
since the fan speed in the metrics table always reflects the real fan speed,we
can fetch the fan speed for both auto and manual mode.
Signed-off-by: NKenneth Feng <kenneth.feng@amd.com>
Reviewed-by: NLikun Gao <Likun.Gao@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Stop registering the SMU i2c bus on navi1x.  This leads to instability
issues when userspace processes mess with the bus and also seems to
cause display stability issues in some cases.

Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1314
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1341Reviewed-by: NEvan Quan <evan.quan@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

There is a problem that if vc4_drm bind fails, a memory leak occurs on
the drm_property_create side. Add error handding for drm_mode_config.
Signed-off-by: NHoegeun Kwon <hoegeun.kwon@samsung.com>
Signed-off-by: NMaxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20201027041442.30352-2-hoegeun.kwon@samsung.com

As reported by "make htmldocs":

	./drivers/gpu/drm/drm_prime.c:808: warning: Function parameter or member 'dev' not described in 'drm_prime_pages_to_sg'

Add a description for the new parameter.

Fixes: 707d561f ("drm: allow limiting the scatter list size.")
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>
Acked-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/9366f48e6e9c3ec2f31a3e68452a2b23a1089fce.1603791716.git.mchehab+huawei@kernel.org

The name of the argument is different, causing those warnings:

	./drivers/gpu/drm/drm_edid.c:3754: warning: Function parameter or member 'video_code' not described in 'drm_display_mode_from_cea_vic'
	./drivers/gpu/drm/drm_edid.c:3754: warning: Excess function parameter 'vic' description in 'drm_display_mode_from_cea_vic'

Fixes: 7af655bc ("drm/dp: Add drm_dp_downstream_mode()")
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7f4d6c3ff6df63ebd006eb90a5108006c23e2168.1603791716.git.mchehab+huawei@kernel.org

As warned by kernel-doc:

	./drivers/gpu/drm/drm_dp_helper.c:385: warning: Function parameter or member 'type' not described in 'drm_dp_downstream_is_type'
	./drivers/gpu/drm/drm_dp_helper.c:886: warning: Function parameter or member 'dev' not described in 'drm_dp_downstream_mode'

Some function parameters weren't documented.

Fixes: 38784f6f ("drm/dp: Add helpers to identify downstream facing port types")
Reviewed-by: NLyude Paul <lyude@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/03c9c8ba3f492aca76e2b4836803219cd9c971cf.1603791716.git.mchehab+huawei@kernel.org

Changeset e5b92773 ("drm: report dp downstream port type as a subconnector property")
added a new function to the kAPI, but didn't add any documentation
for the parameters for drm_dp_set_subconnector_property().

Fixes: e5b92773 ("drm: report dp downstream port type as a subconnector property")
Signed-off-by: NMauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/0870be85a77bea4ba5cf1715010834289a4e10b1.1603791716.git.mchehab+huawei@kernel.org

This patch simplifies the ASSERT*() and BREAK_TO_DEBUGGER() macros:
- Move the dependency check of CONFIG_KGDB into Kconfig
- Unify the kgdb_breakpoint() call
- Drop the non-existing CONFIG_HAVE_KGDB

Also align the behavior of ASSERT() macro in both cases with and
without CONFIG_DEBUG_KERNEL_DC.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

ASSERT_CRITICAL() invokes kgdb_breakpoint() whenever either
CONFIG_KGDB or CONFIG_HAVE_KGDB is set.  This, however, may lead to a
kernel panic when no kdb stuff is attached, since the
kgdb_breakpoint() call issues INT3.  It's nothing but a surprise for
normal end-users.

For avoiding the pitfall, make the kgdb_breakpoint() call only when
CONFIG_DEBUG_KERNEL_DC is set.

https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Currently both error code paths handled in dal_gpio_open_ex() issues
ASSERT_CRITICAL(), and this leads to a kernel panic unnecessarily if
CONFIG_KGDB is enabled.  Since basically both are non-critical errors
and can be recovered, drop those assert calls and use a safer one,
BREAK_TO_DEBUGGER(), for allowing the debugging, instead.

BugLink: https://bugzilla.opensuse.org/show_bug.cgi?id=1177973
Cc: <stable@vger.kernel.org>
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Reviewed-by: NNicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>