We now have 9000 devices that support multiple frames in
a single RB. Enable it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Integrated 9000 devices have a bug with shadow registers
value retention.
If driver writes RBD registers while MAC is asleep the
values are stored in shadow registers to be copied whenever
MAC wakes up.
However, in 9000 devices a MAC wakeup is not triggered
and when the bus powers down due to inactivity the shadow
values and dirty bits are lost.
Turn on the chicken-bits that cause MAC wakeup for RX-related
values as well when the device is in D0.
When the device is in low power mode turn the RX wakeup chicken
bits off since driver is idle and this W/A is not needed.
Remove previous W/A which was ineffective.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support queue removal in DQA mode in iwl_mvm_rm_sta() also when
the device isn't a STA connected to an AP.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

rx_phy notification is no longer sent in devices with
multiple rx queues.
All the needed data is now set in the metadata - update
code accordingly to reflect all the features as in the
previous RX path.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In multiple RX queues architecture, the RX_PHY notification
is no longer useful as it is received in the default queue
even for packets that are received on RSS queue, and cannot
be accessed without locking.
All the needed data is in the new RX packet metadata and
firmware will no longer send this notification for 9000
devices. Remove support of it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Ucode capability bit 26 indicates support for UAPSD on P2P interface
even with a simultaneous BSS station interface, as long as both
interfaces are in the same binding. Change the name of the
capability bit to reflect that.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Somehow we ended up without leading spaces here, fix that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We cannot trust NSSN for AMSDU sub-frames that are not the
last.
The reason is that NSSN advances on the first sub-frame,
and may cause the reorder buffer to advance before all the
sub-frames arrive.
Example:
Reorder buffer contains SN 0 & 2.
We receive AMSDU with SN 1 and NSSN for first sub frame 3.
The result us that driver releases SN 0,1, 2.
When sub-frame 1 arrives - reorder buffer is already ahead and
it will be dropped.
If the last sub-frame is not on this queue - we will get frame
release notification with up to date NSSN.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The new hardware that supports multiple queue also
de-aggregates A-MSDUs. This means that we can advertise
the maximal size of A-MSDUs regardless of the receive
buffer's size.
In order to be able to forcefully use a lower A-MSDU size,
add a default value for the module parameter. Pre-9000
will have a default of 4K, and 9000 will have 12K.
Setting the amsdu_size module parameter to 4K will limit
the A-MSDU on 9000 as well.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

I'm starting to take a more active role in the iwlwifi driver
maintainership.

Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Small change to make it clear that the default value is false.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When initializing RX we grab NIC access for every read and
write. This is redundant - we can just grab access once.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The RX queues have a shadow register for the write pointer
that enables updates without grabbing NIC access. Use them
instead of the periphery registers because accessing those
is much more expensive.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In non-shared queues, DQA requires re-configuring existing
queues to become aggregated rather than allocating a new
one. It also requires "un-aggregating" an existing queue
when aggregations are turned off.

Support this requirement for non-shared queues.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since msleep is based on jiffies, it can sleep for a long time.
Use usleep_range() instead to shorten the maximum time.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Newer hardware generations will take longer to be accessible again
after reset, so we need to wait longer before continuing any flow
that did a reset.

Rather than make the wait time configurable, simply extend it for
all.

Since all of these code paths can sleep, use usleep_range() rather
than mdelay().
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Devices supporting VHT 160MHz width are supporting also Short GI.
Turn on this capability in vht cap.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since we have a lot of configuration structs (almost 70) saving
some memory in each one of them leads to an overall saving of
~2.6KiB of memory.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The commit below added code to dump the content of FIFOs
that are present only on dual CPU products (8000 and up).
This broke 7265D whose firmware does advertise
IWL_UCODE_TLV_CAPA_EXTEND_SHARED_MEM_CFG but doesn't have 2
CPUs. The current code does check the length of the FIFO
before dumping them (and the nonexistent FIFO has a 0
length), but we still accessed a register to set the FIFO
number and that made the DMA unhappy.

The impact was a much longer recovery upon firmware assert.

Fixes: 5b086414 ("iwlwifi: mvm: support dumping UMAC internal txfifos")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This Kconfig option allows to load a firmware for
debugging with a different name. This mechanism has not
been used for a few years now and replacing the firmware
file works as well.
Kill this Kconfig option and all the code that goes with it.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Getting the mvm station out of station id requires dereferencing
the station id to get ieee80211_sta, then checking for pointer
validity and only then extract mvm station out.
Given that there are helpers to do it - use them instead of
duplicating the code whenever we need only mvm station.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_phy_db_set_section() is get called only from atomic
context, the alloc_ctx parameter is not needed. Remove it.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Driver is agnostic to the number of the phy_db entries and
only serves the firmware as a pipe to move the data from init
image to RT image.
As the size of the arrays may change (as it does in 9000 device)
allocate it dynamically. Firmware sends the largest index first
so we can use this to know how much we should allocate.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Our device supports only 160 GHz and not 80+80. Fix
VHT flag accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Up till now, the reorder buffer uses standard spec based comparison
when comparing the buffer status to NSSN. This indeed works for the
regular case, since we shouldn't cross the 2048 boundary without
getting a frame release notification.
However, this is problematic due to packet filtering that may be
performed by the FW while we are in d0i3. Theoretically we may
filter over 2048 packets, and then the check of the NSSN will get
incorrect.
Change the comparison to always trust nssn unless it is 64 or less
frames behind the head - which might happen due to a timeout.
This new comparison is to be used only when comparing reorder buffer
head with nssn, and not when comparing the packet SN to nssn or
reorder buffer head.
Put this in a separate commit as the logic is a bit tricky and
stands for its own commit message.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

CSR registers are always available even when the NIC is not awake, no
need to wake up the NIC before accessing them. This has a huge impact
when we re-enable an interrupt at the end of the ISR since waking up the
NIC can take some time.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Previous patch had changed firmware name convention for
new generation product. The firmware name is now longer
than the former convention. Adapt max firmware name length
to the new convention.

Fixes: e1ba684f ("iwlwifi: 8000: fix MODULE_FIRMWARE input")
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently code allows mvm reference to become negative and
only warns in case mvm reference is released while reference
counting is 0.
However, we better prevent this from happening at all since
iwl_mvm_unref() may race against iwl_mvm_unref_all_except()
which is called on restart.
As a result we might get the same reference unreferenced twice
ending with a negative value:
An example for an easily reproduced log:
    [ 2689.909166] iwl_mvm_ref Take mvm reference - type 8
    [ 2690.732716] iwl_mvm_unref_all_except Cleanup: remove mvm ref type 8 (1)
    [ 2690.849708] iwl_mvm_unref Leave mvm reference - type 8
    [ 2690.849721] WARNING: ... iwl_mvm_unref+0xb0/0xc0 [iwlmvm]()

If there will be yet another another restart iwl_mvm_unref_all_except
will run from 0 up to ref count, and since it is unsigned, we will throw
the transport ref count completely out of balance:
    iwl_mvm_unref_all_except[I] -- Cleanup: remove mvm ref type 8 (255)
    iwl_trans_slv_unref[I] -- rpm counter: 0
    iwl_trans_slv_unref[I] -- rpm counter: -1
    iwl_trans_slv_unref[I] -- rpm counter: -2
 ...
    iwl_trans_slv_unref[I] -- rpm counter: -253
    iwl_trans_slv_unref[I] -- rpm counter: -254

As there is no valid scenario where we can get to a negative
reference count - prevent it from happening.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add UREG, RXFC, RFH, WMAL and RL2P registers to the prph dump
upon error. These regesiters could help to debug MSI-X and other
issues.

These register should be dumped only when multi-queue rx is supported
so separate the prph ranges static array to two different arrays,
and enable dumping different prph ranges according to run-time
decision.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When a data packet is received, we need to make sure that we stay
awake until it can be processed and wait a while before trying to
enter runtime_suspend os system_suspend again.  To do so, add a new
reference type for RX data and take the reference when sending the
packet to mac80211.  We only do this for data packets, all the other
RX packets sent by the firmware (e.g. notifications) are not a reason
to prevent suspend.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we've already looked up the transmitter station, we can just
pass it to mac80211 using the new ieee80211_rx_napi(). This saves
the overhead of looking it up in mac80211 again.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Devices belonging to 9000 family can support VHT 160MHz channel
width, so need to consider it when configuring VHT capabilities.
However, NVM file doesn't have a single bit specifying that 160MHz
is supported. This patch turns on 160MHz support in VHT capabilities
in case there's at least one channel supporting 160MHz.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently there is one to one function between device id to it's ucode.
The new generation devices allows to combine different phy and mac images.
Now we have two different ucode images with the same device id.
Read RF ID to identify phy image and overwrite it if needed.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If a host command was queued while in runtime suspend, it would go out
before the D0I3_END_CMD was sent.  Sometimes it works, but sometimes
it fails, and it is obviously the wrong thing to do.

To fix this, have the opmode take a reference before sending a SYNC
command and make the pcie trans wait for the runtime state to become
active before actually queueing the command.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There is a debugfs knob to configure the maximal length
of the A-MSDU. If this value is not 0 (which is the
default), allow Tx A-MSDU even if the rate control
disallows it.
While at it, add "unlikely" to the if that limits the
length of the A-MSDU based on the debugfs hook.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Rename 9560 to 9260.
Add new PCI ID for 9260 and change some entries from 5165 to 9260.
Also order the 9000 series.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add a constant to allow disabling checksum. This will enable easier
debugging in early phases.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order for mac80211 to use per-CPU statistics for RSS RX, the
driver needs to advertise that it uses RSS. Do this when using
more than a single queue.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

It's cleaner to always call the iwl_trans_ref/unref() functions
instead of sometimes calling the trans-specific ops directly.  This
also prepares for moving some of the code from the trans-specific ops
to the common trans code.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>