Introduce an inline function pci_pcie_type(dev) to extract PCIe
device type from pci_dev->pcie_flags_reg field, and prepare for
removing pci_dev->pcie_type.
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NJiang Liu <jiang.liu@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>

The skb->pfmemalloc flag gets set to true iff during the slab allocation
of data in __alloc_skb that the the PFMEMALLOC reserves were used.  If
page splitting is used, it is possible that pages will be allocated from
the PFMEMALLOC reserve without propagating this information to the skb.
This patch propagates page->pfmemalloc from pages allocated for fragments
to the skb.

It works by reintroducing and expanding the skb_alloc_page() API to take
an skb.  If the page was allocated from pfmemalloc reserves, it is
automatically copied.  If the driver allocates the page before the skb, it
should call skb_propagate_pfmemalloc() after the skb is allocated to
ensure the flag is copied properly.

Failure to do so is not critical.  The resulting driver may perform slower
if it is used for swap-over-NBD or swap-over-NFS but it should not result
in failure.

[davem@davemloft.net: API rename and consistency]
Signed-off-by: NMel Gorman <mgorman@suse.de>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Cc: Neil Brown <neilb@suse.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Christie <michaelc@cs.wisc.edu>
Cc: Eric B Munson <emunson@mgebm.net>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Christoph Lameter <cl@linux.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch resolves a "BUG: unable to handle kernel paging request at ..."
oops while dumping packet data. The issue occurs with IOMMU enabled due to
the address provided by phys_to_virt().

This patch makes use of skb->data on Tx and the virtual address of the pages
allocated for Rx.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that we can use 1TC DCB in the case of MSI and
legacy interrupts.  The advantage to this is that it allows us to fully
support FCoE w/ DCB instead of having to drop to link flow control only
when using these interrupt modes.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds support for a new 82599 device that supports WoL.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

With DCB and FCoE configured extra queues may be allocated and
never used. After this patch we calculate the max correctly.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Do RAR entry accounting correctly so that errors are reported and
promisc mode is set correctly when the number of entries exceeds
the hardware limits.

This can happen with many macvlan devices attached to the PF or
by adding many fdb entries in SR-IOV modes.

Also this includes a small refactor to fdb_add() to avoid having so
many nested if/else statements after adding a check for the number
or RAR entries.

The max entries for the PF is currently 16 we allow 15 additional
entries to account for the defined MAC.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The recent changes to netdev_alloc_skb actually make it so that the size of
the buffer now actually has a more direct input on the truesize.  So in
order to make best use of the piece of a page we are allocated I am
reducing the IXGBE_RX_HDR_SIZE to 256 so that our truesize will be reduced
by 256 bytes as well.

This should result in performance improvements since the number of uses per
page should increase from 4 to 6 in the case of a 4K page.  In addition we
should see socket performance improvements due to the truesize dropping
to less than 1K for buffers less than 256 bytes.

Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can use the atr_sample_rate to determine if
we are capable of supporting ATR. The advantage to this approach is that it
allows us to now determine the setting of the IXGBE_FLAG_FDIR_HASH_CAPABLE
based on the queueing scheme, instead of the queueing scheme being based on
the flag.

Using this approach there are essentially 5 conditions that must be checked
prior to trying to enable ATR:
1.  Is SR-IOV disabled?
2.  Are the number of TCs <= 1?
3.  Is RSS queueing limit greater than 1?
4.  Is atr_sample_rate set?
5.  Is Flow Director perfect filtering disabled?

If any of these conditions are enabled they should disable ATR filtering.
Note that in the case of conditions 1 through 4 being met we will set
things up for ATR queueing, however if test 5 fails we will still leave the
queues allocated for use by perfect filters.  The reason for this is to
allow for us to switch back and forth between ntuple and ATR without
needing to reallocate the descriptor rings.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch does two things.  First it drops the unnecessary work of
searching for enabled VFs when we first bring up the adapter and instead
just uses pci_num_vf to determine how many VFs are enabled on the adapter.

The second thing it does is drop the use of vfdev from the vf_data_storage
structure.  Instead we just search the entire system for a VF that has us
as it's PF, and then if that VF is assigned we indicate that the VFs are
assigned.  This allows us to still check for assigned VFs even if the
vfinfo allocation has failed, or vfinfo has been freed.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This is meant to fix a bug in which we were not checking for pre-existing
VFs if we were not setting the max_vfs value at driver load.  What happens
now is that we always call ixgbe_enable_sriov and this checks for
pre-existing VFs ore requested VFs prior to deciding on no SR-IOV.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use PCI_VENDOR_ID_INTEL from pci_ids.h instead of creating its own
vendor ID #define.
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Cc: Alex Duyck <alexander.h.duyck@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of only setting the FCOE segmentation offload and CRC offload flags
if we enable FCoE, we could just set them always since there are no
modifications needed to the hardware or adapter FCoE structure in order to
use these features.

The advantage to this is that if FCoE enablement fails, for example because
SR-IOV was enabled on 82599, we will still have use of the FCoE
segmentation offload and Tx/Rx CRC offloads which should still help to
improve the FCoE performance.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change corrects an issue in which an FCoE enabled adapter was always
setting the FCoE SAN MAC MPSAR register to 0x1.  This results in the first
VF being assigned the SAN MAC address in the case of SR-IOV and as such is
incorrect.  To resolve this I am adding a new function that will update the
SAN MAC pool address after reset.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes the behavior of the FCoE configuration so that it is
much closer to how the main body of the ixgbe driver works for ring
allocation.

The first piece is the ixgbe_fcoe_ddp_enable/disable calls.  These allocate
the percpu values and if successful set the fcoe_ddp_xid value indicating
that we can support DDP.

The next piece is the ixgbe_setup/free_ddp_resources calls.  These are
called on open/close and will allocate and free the DMA pools.

Finally ixgbe_configure_fcoe is now just register configuration.  It can go
through and enable the registers for the FCoE redirection offload, and FIP
configuration without any interference from the DDP pool allocation.

The net result of all this is two fold.  First it adds a certain amount of
exception handling.  So for example if ixgbe_setup_fcoe_resources fails we
will actually generate an error in open and refuse to bring up the
interface.

Secondly it provides a much more graceful failure case than the previous
model which would skip setting up the registers for FCoE on failure to
allocate DDP resources leaving no Rx functionality enabled instead of just
disabling DDP.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change merges the 2 statistics values for noddp and noddp_ext_buff
and the dma_pool into a single structure that can be allocated per CPU.

The advantages to this are several fold.  First we only need to do one
alloc_percpu call now instead of 3, so that means less overhead for
handling memory allocation failures.  Secondly in the case of
ixgbe_fcoe_ddp_setup we only need to call get_cpu once which makes things a
bit cleaner since we can drop a put_cpu() from the exception path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change makes it so that we can use the VMDq ring feature offset value
to determine the default pool instead of using num_vfs.  The reason for
this change is to avoid issues should we fail to allocate vfinfo but have
pre-existing VFs.  What should happen in this case is that num_vfs will go
to 0, but the VMDq offset will contain the location of the first PF pool.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <Sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All of our hardware supports RSS even if it is only for a single queue.  So
instead of toting around the RSS enable flag I am updating the code so that
all devices are enabled and if we want to disable RSS it is indicated via
the RSS mask.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change essentially makes it so that we can enable almost all of the
features all at once.  This patch allows for the combination of SR-IOV,
DCB, and FCoE in the case of the x540.  It also beefs up the SR-IOV by
adding support for RSS to the PF.

The testing matrix gets to be very complex for this patch as there are a
number of different features and subsets for queueing options.  I tried to
narrow these down a bit by restricting the PF to only supporting 4TC DCB
when it is enabled in addition to SR-IOV.

Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change allows all pools from the default pool forward to be enabled vi
ixgbe_configure_virtualization.  This is needed as we are planning to use
queues belonging to adjacent pools for FCoE when SR-IOV and FCoE are both
enabled.

In addition this patch contains some minor formatting changes as there were
a few spots that seemed to be in need of some cleanup.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change is meant to make the code much more readable for MTQC and MRQC
configuration.

The big change is that I simplified much of the logic so that we are
essentially handling just 4 cases and their variants. In the cases where
RSS is disabled we are actually just programming the RETA table with all
1s resulting in a single queue RSS. In the case of SR-IOV I am treating
that as a subset of VMDq. This all results int he following configuration
for the hardware:
         DCB
         En       Dis
VMDq En  VMDQ/DCB VMDq/RSS
     Dis DCB/RSS  RSS

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change cleans up some of the logic in an attempt to try and simplify
things for how we are configuring DCB w/ RSS.

In this patch I basically did 3 things.  I updated the logic for getting
the first register index.  I applied the fact that all TCs get the same
number of queues to simplify the looping logic in caching the DCB ring
register.  Finally I updated how we configure the RQTC register to match
the fact that all TCs are assigned the same number of queues.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to configure the real number of Tx and Rx
queues in the ixgbe_open call than it does in ixgbe_set_num_queues.  By
setting the number in ixgbe_open we can avoid a number of unecessary
updates and only have to make the calls once.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously we were exiting without cleaning up the memory internally on the
ixgbe_setup_rx_resources and ixgbe_setup_tx_resources calls.  Instead of
forcing the caller to clean things up for us we should instead just unwind
the rings and free the memory as we go.  This way we can more gracefully
clean up the rings in the event of an allocation failure.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the link status changes on the PF we need to notify the VFs. In order
to do this we should ping all of the VFs in order to trigger a link status
change on them as well.

This fixes issues in which the PF would reset, but the VF didn't because the
NAK flag was not set in the VF mailbox.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NSibai Li <sibai.li@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This change merges the ixgbe_cache_ring_fcoe and ixgbe_set_fcoe_queues
logic into the DCB and RSS initialization calls.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In upcoming patches it will become increasingly common to need to determine
the FCoE traffic class in order to determine the correct queues for FCoE.
In order to make this easier I am adding a function for obtaining the FCoE
traffic class based on the user priority.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There were cases where the prio_tc_map was not populated when we were
calling open.  This will result in us incorrectly configuring the traffic
classes when DCB is enabled.  In order to correct this I have updated the
code so that we now populate the values prior to allocating the q_vectors
and calling ixgbe_open.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces a switch statement for an 82598 workaround with an if
statement that only applies to 82598. In addition I am pulling out several
dead pieces of code and instead of reading the SRRCTL register and then
modifying it we are just writing a value which we generate from scratch.
Finally I am also removing any drop enable related code since that was
moved to a function of its own.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The mask value for ring features was overloaded for FCoE which can lead to
some confusion.  In order to avoid any confusion I am splitting the mask
value and adding an offset value.  This can be used for the start of the
FCoE rings, and in the future I hope to use it to store the start of the
registers for SR-IOV.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

We are currently using indices to indicate the upper limit on a ring
feature.  However since we can switch back and forth on features such as
DCB and that has effects on other features such as RSS it is preferable to
instead store the upper limit separate from the current value for the
number of rings related to the feature.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

It makes much more sense for us to count q_vectors instead of MSI-X
vectors.  We were using num_msix_vectors to find the number of q_vectors in
multiple places.  This was wasteful since we only had one place that
actually needs the number of MSI-X vectors and that is in slow path.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.  Delete
a few that are content-free.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DCB and SR-IOV cannot currently be enabled at the same time as the queueing
schemes are incompatible.  If they are both enabled it will result in Tx
hangs since only the first Tx queue will be able to transmit any traffic.

This simple fix for this is to block us from enabling TCs in ixgbe_setup_tc
if SR-IOV is enabled.  This change will be reverted once we can support
SR-IOV and DCB coexistence.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FCoE target mode was experiencing issues due to the fact that we were
sending up data frames that were padded to 60 bytes after the DDP logic had
already stripped the frame down to 52 or 56 depending on the use of VLANs.
This was resulting in the FCoE DDP logic having issues since it thought the
frame still had data in it due to the padding.

To resolve this, adding code so that we do not pad FCoE frames prior to
handling them to the stack.

CC: <stable@vger.kernel.org>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The check for length <= 0 is bogus because length is unsigned, and network
stack never sends zero length packets (unless it is totally broken).

The check for really small packets can be optimized (using unlikely)
and calling skb_pad directly.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a memory leak that was introduced in the 3.4 kernel.  The
leak occurred when FCoE was enabled and traffic was passed over the FCoE
rings reserved for FCoE.  The memory leak was due to us not populating the
compound page information on the order 1 pages needed for FCoE.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes a potential Rx timestamp deadlock that causes the Rx
timestamping to stall indefinitely. The issue could occur when a PTP packet is
timestamped by hardware but never reaches the Rx queue. In order to prevent a
permanent loss of timestamping, the RXSTMP(L/H) registers have to be read to
unlock them. (This used to only occur when a packet that was timestamped
reached the software.) However the registers can't be read early otherwise
there is no way to correlate them to the packet.

This patch introduces a filter function which can be used to determine if a
packet should have been timestamped. Supplied with the filter setup by the
hwtstamp ioctl, check to make sure the PTP protocol and message type match the
expected values. If so, then read the timestamp registers (to free them.) At
this point check the descriptor bit, if the bit is set then we know this
packet correlates to the timestamp stored in the RXTSTAMP registers.
Otherwise, assume that packet was dropped by the hardware, and ignore this
timestamp value. However, we have at least unlocked the rxtstamp registers for
future timestamping.

Due to the way the driver handles skb data, it cannot be directly accessed. In
order to work around this, a copy of the skb data into a linear buffer is
made. From this buffer it becomes possible to read the data correctly
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NRichard Cochran <richardcochran@gmail.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes two minor nits from Richard Cochran. The first is a case of
ambitious line wrapping that wasn't necessary. The second is to re-order the
flag checks for PPS support. Previously, the hardware test was done first, and
the interrupt flag test was done second. Now, test the interrupt flag and use
the unlikely macro.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NPhil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware bit IXGBE_RXD_STAT_VP appears to be set even when Rx
stripping is disabled. This results in passing frames up the stack
which do not have the 802.1Q tag stripped but have the tci bits
set as if it was.

Working around this with a check for the feature flag bit. I
would welcome any better ideas or a pointer to exactly which
bits in the hardware register need to be cleared to get the
IXGBE_RXD_STAT_VP bit to be set per data sheet.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NMarcus Dennis <marcusx.e.dennis@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>