STA control register has areas of mode and opcodes for opeations. 18 bit is
using for mode selection, where 0 is old MIO/MDIO access method and 1 is
indirect access mode. 19-20 bits are using for setting up read/write
operation(STA opcodes). In current state 'read' is set into old MIO/MDIO mode
with 19 bit and write operation is set into 18 bit which is mode selection,
not a write operation. To correlate write with read we set it into 20 bit.
All those bit operations are MSB 0 based.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

emac4syn chips has availability to use 8192 rx/tx fifo buffer sizes,
in current state if we set it up in dts 8192 as example, we will get
only 2048 which may impact on network speed.
Signed-off-by: NIvan Mikhaylov <ivan@de.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code will try to access dev->iotlb when processing
VHOST_IOTLB_INVALIDATE even if it was not initialized which may lead
to NULL pointer dereference. Fixes this by check dev->iotlb before.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We used to call mutex_lock() in vhost_dev_lock_vqs() which tries to
hold mutexes of all virtqueues. This may confuse lockdep to report a
possible deadlock because of trying to hold locks belong to same
class. Switch to use mutex_lock_nested() to avoid false positive.

Fixes: 6b1e6cc7 ("vhost: new device IOTLB API")
Reported-by: syzbot+dbb7c1161485e61b0241@syzkaller.appspotmail.com
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since TC block changes drivers are required to check if
the TC hw offload flag is set on the interface themselves.

Fixes: 2f4b411a ("i40e: Enable cloud filters via tc-flower")
Fixes: 44ae12a7 ("net: sched: move the can_offload check from binding phase to rule insertion phase")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michal Kalderon says:

====================
qed: rdma bug fixes

This patch contains two small bug fixes related to RDMA.
Both related to resource reservations.
====================
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A tid was allocated for reserved MR during initialization but
not freed. This lead to an annoying output message during
rdma unload flow.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Double reservation for kernel dedicated dpi was performed.
Once in the core module and once in qedr.
Remove the reservation from core.
Signed-off-by: NMichal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: NAriel Elior <Ariel.Elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tom Herbert says:

====================
kcm: fix two syzcaller issues

In this patch set:

- Don't allow attaching non-TCP or listener sockets to a KCM mux.
- In kcm_attach Check if sk_user_data is already set. This is
  under lock to avoid race conditions. More work is need to make
  all of the users of sk_user_data to use the same locking.

- v2
  Remove unncessary check for not PF_KCM in kcm_attach (suggested by
  Guillaume Nault)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is needed to prevent sk_user_data being overwritten.
The check is done under the callback lock. This should prevent
a socket from being attached twice to a KCM mux. It also prevents
a socket from being attached for other use cases of sk_user_data
as long as the other cases set sk_user_data under the lock.
Followup work is needed to unify all the use cases of sk_user_data
to use the same locking.

Reported-by: syzbot+114b15f2be420a8886c3@syzkaller.appspotmail.com
Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Signed-off-by: NTom Herbert <tom@quantonium.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCP sockets for IPv4 and IPv6 that are not listeners or in closed
stated are allowed to be attached to a KCM mux.

Fixes: ab7ac4eb ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+8865eaff7f9acd593945@syzkaller.appspotmail.com
Signed-off-by: NTom Herbert <tom@quantonium.net>
Reviewed-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TCF_LAYER_LINK and TCF_LAYER_NETWORK returned the same pointer as
skb->data points to the network header.
Use skb_mac_header instead.
Signed-off-by: NWolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'ptr' is shifted by the offset and then validated,
the memcmp should not add it a second time.
Signed-off-by: NWolfgang Bumiller <w.bumiller@proxmox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver periodically samples all neighbors configured in device
in order to update the kernel regarding their state. When finding
an entry configured in HW that doesn't show in neigh_lookup()
driver logs an error message.
This introduces a race when removing multiple neighbors -
it's possible that a given entry would still be configured in HW
as its removal is still being processed but is already removed
from the kernel's neighbor tables.

Simply remove the error message and gracefully accept such events.

Fixes: c723c735 ("mlxsw: spectrum_router: Periodically update the kernel's neigh table")
Fixes: 60f040ca ("mlxsw: spectrum_router: Periodically dump active IPv6 neighbours")
Signed-off-by: NYuval Mintz <yuvalm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net): ipsec 2018-01-24

1) Only offloads SAs after they are fully initialized.
   Otherwise a NIC may receive packets on a SA we can
   not yet handle in the stack.
   From Yossi Kuperman.

2) Fix negative refcount in case of a failing offload.
   From Aviad Yehezkel.

3) Fix inner IP ptoro version when decapsulating
   from interaddress family tunnels.
   From Yossi Kuperman.

4) Use true or false for boolean variables instead of an
   integer value in xfrm_get_type_offload.
   From Gustavo A. R. Silva.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

with the introduction of commit
b0eb57cb, it appears that rq->buf_info
is improperly handled.  While it is heap allocated when an rx queue is
setup, and freed when torn down, an old line of code in
vmxnet3_rq_destroy was not properly removed, leading to rq->buf_info[0]
being set to NULL prior to its being freed, causing a memory leak, which
eventually exhausts the system on repeated create/destroy operations
(for example, when  the mtu of a vmxnet3 interface is changed
frequently.

Fix is pretty straight forward, just move the NULL set to after the
free.

Tested by myself with successful results

Applies to net, and should likely be queued for stable, please
Signed-off-by: NNeil Horman <nhorman@tuxdriver.com>
Reported-By: boyang@redhat.com
CC: boyang@redhat.com
CC: Shrikrishna Khare <skhare@vmware.com>
CC: "VMware, Inc." <pv-drivers@vmware.com>
CC: David S. Miller <davem@davemloft.net>
Acked-by: NShrikrishna Khare <skhare@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 513674b5 ("net: reevalulate autoflowlabel setting after
sysctl setting") removed the initialisation of
ipv6_pinfo::autoflowlabel and added a second flag to indicate
whether this field or the net namespace default should be used.

The getsockopt() handling for this case was not updated, so it
currently returns 0 for all sockets for which IPV6_AUTOFLOWLABEL is
not explicitly enabled.  Fix it to return the effective value, whether
that has been set at the socket or net namespace level.

Fixes: 513674b5 ("net: reevalulate autoflowlabel setting after sysctl ...")
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In pppoe_sendmsg(), reserving dev->hard_header_len bytes of headroom
was probably fine before the introduction of ->needed_headroom in
commit f5184d26 ("net: Allow netdevices to specify needed head/tailroom").

But now, virtual devices typically advertise the size of their overhead
in dev->needed_headroom, so we must also take it into account in
skb_reserve().
Allocation size of skb is also updated to take dev->needed_tailroom
into account and replace the arbitrary 32 bytes with the real size of
a PPPoE header.

This issue was discovered by syzbot, who connected a pppoe socket to a
gre device which had dev->header_ops->create == ipgre_header and
dev->hard_header_len == 0. Therefore, PPPoE didn't reserve any
headroom, and dev_hard_header() crashed when ipgre_header() tried to
prepend its header to skb->data.

skbuff: skb_under_panic: text:000000001d390b3a len:31 put:24
head:00000000d8ed776f data:000000008150e823 tail:0x7 end:0xc0 dev:gre0
------------[ cut here ]------------
kernel BUG at net/core/skbuff.c:104!
invalid opcode: 0000 [#1] SMP KASAN
Dumping ftrace buffer:
    (ftrace buffer empty)
Modules linked in:
CPU: 1 PID: 3670 Comm: syzkaller801466 Not tainted
4.15.0-rc7-next-20180115+ #97
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
RIP: 0010:skb_panic+0x162/0x1f0 net/core/skbuff.c:100
RSP: 0018:ffff8801d9bd7840 EFLAGS: 00010282
RAX: 0000000000000083 RBX: ffff8801d4f083c0 RCX: 0000000000000000
RDX: 0000000000000083 RSI: 1ffff1003b37ae92 RDI: ffffed003b37aefc
RBP: ffff8801d9bd78a8 R08: 1ffff1003b37ae8a R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff86200de0
R13: ffffffff84a981ad R14: 0000000000000018 R15: ffff8801d2d34180
FS:  00000000019c4880(0000) GS:ffff8801db300000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000000208bc000 CR3: 00000001d9111001 CR4: 00000000001606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
  skb_under_panic net/core/skbuff.c:114 [inline]
  skb_push+0xce/0xf0 net/core/skbuff.c:1714
  ipgre_header+0x6d/0x4e0 net/ipv4/ip_gre.c:879
  dev_hard_header include/linux/netdevice.h:2723 [inline]
  pppoe_sendmsg+0x58e/0x8b0 drivers/net/ppp/pppoe.c:890
  sock_sendmsg_nosec net/socket.c:630 [inline]
  sock_sendmsg+0xca/0x110 net/socket.c:640
  sock_write_iter+0x31a/0x5d0 net/socket.c:909
  call_write_iter include/linux/fs.h:1775 [inline]
  do_iter_readv_writev+0x525/0x7f0 fs/read_write.c:653
  do_iter_write+0x154/0x540 fs/read_write.c:932
  vfs_writev+0x18a/0x340 fs/read_write.c:977
  do_writev+0xfc/0x2a0 fs/read_write.c:1012
  SYSC_writev fs/read_write.c:1085 [inline]
  SyS_writev+0x27/0x30 fs/read_write.c:1082
  entry_SYSCALL_64_fastpath+0x29/0xa0

Admittedly PPPoE shouldn't be allowed to run on non Ethernet-like
interfaces, but reserving space for ->needed_headroom is a more
fundamental issue that needs to be addressed first.

Same problem exists for __pppoe_xmit(), which also needs to take
dev->needed_headroom into account in skb_cow_head().

Fixes: f5184d26 ("net: Allow netdevices to specify needed head/tailroom")
Reported-by: syzbot+ed0838d0fa4c4f2b528e20286e6dc63effc7c14d@syzkaller.appspotmail.com
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Reviewed-by: NXin Long <lucien.xin@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Fix divide by zero in mlx5, from Talut Batheesh.

 2) Guard against invalid GSO packets coming from untrusted guests and
    arriving in qdisc_pkt_len_init(), from Eric Dumazet.

 3) Similarly add such protection to the various protocol GSO handlers.
    From Willem de Bruijn.

 4) Fix regression added to IGMP source address checking for IGMPv3
    reports, from Felix Feitkau.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
  tls: Correct length of scatterlist in tls_sw_sendpage
  be2net: restore properly promisc mode after queues reconfiguration
  net: igmp: fix source address check for IGMPv3 reports
  gso: validate gso_type in GSO handlers
  net: qdisc_pkt_len_init() should be more robust
  ibmvnic: Allocate and request vpd in init_resources
  ibmvnic: Revert to previous mtu when unsupported value requested
  ibmvnic: Modify buffer size and number of queues on failover
  rds: tcp: compute m_ack_seq as offset from ->write_seq
  usbnet: silence an unnecessary warning
  cxgb4: fix endianness for vlan value in cxgb4_tc_flower
  cxgb4: set filter type to 1 for ETH_P_IPV6
  net/mlx5e: Fix fixpoint divide exception in mlx5e_am_stats_compare

Assign true or false to boolean variables instead of an integer value.

This issue was detected with the help of Coccinelle.

Fixes: ffdb5211 ("xfrm: Auto-load xfrm offload modules")
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

IPSec tunnel mode supports encapsulation of IPv4 over IPv6 and vice-versa.

The outer IP header is stripped and the inner IP inherits the original
Ethernet header. Tcpdump fails to properly decode the inner packet in
case that h_proto is different than the inner IP version.

Fix h_proto to reflect the inner IP version.
Signed-off-by: NYossi Kuperman <yossiku@mellanox.com>
Signed-off-by: NSteffen Klassert <steffen.klassert@secunet.com>

Commit bdcf0a42 ("kernel: make groups_sort calling a responsibility
group_info allocators") appears to break nfsd rootsquash in a pretty
major way.

It adds a call to groups_sort() inside the loop that copies/squashes
gids, which means the valid gids are sorted along with the following
garbage.  The net result is that the highest numbered valid gids are
replaced with any lower-valued garbage gids, possibly including 0.

We should sort only once, after filling in all the gids.

Fixes: bdcf0a42 ("kernel: make groups_sort calling a responsibility ...")
Signed-off-by: NBen Hutchings <ben.hutchings@codethink.co.uk>
Acked-by: NJ. Bruce Fields <bfields@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In orangefs_devreq_read, there is a loop which picks an op off the list
of pending ops.  If the loop fails to find an op, there is nothing to
read, and it returns EAGAIN.  If the op has been given up on, the loop
is restarted via a goto.  The bug is that the variable which the found
op is written to is not reinitialized, so if there are no more eligible
ops on the list, the code runs again on the already handled op.

This is triggered by interrupting a process while the op is being copied
to the client-core.  It's a fairly small window, but it's there.
Signed-off-by: NMartin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

set_op_state_purged can delete the op.
Signed-off-by: NMartin Brandenburg <martin@omnibond.com>
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The scatterlist is reused by both sendmsg and sendfile.
If a sendmsg of smaller number of pages is followed by a sendfile
of larger number of pages, the scatterlist may be too short, resulting
in a crash in gcm_encrypt.

Add sg_unmark_end to make the list the correct length.

tls_sw_sendmsg already calls sg_unmark_end correctly when it allocates
memory in alloc_sg, or in zerocopy_from_iter.
Signed-off-by: NDave Watson <davejwatson@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The commit 62219066 ("be2net: Request RSS capability of Rx interface
depending on number of Rx rings") modified be_update_queues() so the
IFACE (HW representation of the netdevice) is destroyed and then
re-created. This causes a regression because potential promiscuous mode
is not restored properly during be_open() because the driver thinks
that the HW has promiscuous mode already enabled.

Note that Lancer is not affected by this bug because RX-filter flags are
disabled during be_close() for this chipset.

Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>

Fixes: 62219066 ("be2net: Request RSS capability of Rx interface depending on number of Rx rings")
Signed-off-by: NIvan Vecera <ivecera@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "net: igmp: Use correct source address on IGMPv3 reports"
introduced a check to validate the source address of locally generated
IGMPv3 packets.
Instead of checking the local interface address directly, it uses
inet_ifa_match(fl4->saddr, ifa), which checks if the address is on the
local subnet (or equal to the point-to-point address if used).

This breaks for point-to-point interfaces, so check against
ifa->ifa_local directly.

Cc: Kevin Cernekee <cernekee@chromium.org>
Fixes: a46182b0 ("net: igmp: Use correct source address on IGMPv3 reports")
Reported-by: NSebastian Gottschall <s.gottschall@dd-wrt.com>
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Validate gso_type during segmentation as SKB_GSO_DODGY sources
may pass packets where the gso_type does not match the contents.

Syzkaller was able to enter the SCTP gso handler with a packet of
gso_type SKB_GSO_TCPV4.

On entry of transport layer gso handlers, verify that the gso_type
matches the transport protocol.

Fixes: 90017acc ("sctp: Add GSO support")
Link: http://lkml.kernel.org/r/<001a1137452496ffc305617e5fe0@google.com>
Reported-by: syzbot+fee64147a25aecd48055@syzkaller.appspotmail.com
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Reviewed-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Without proper validation of DODGY packets, we might very well
feed qdisc_pkt_len_init() with invalid GSO packets.

tcp_hdrlen() might access out-of-bound data, so let's use
skb_header_pointer() and proper checks.

Whole story is described in commit d0c081b4 ("flow_dissector:
properly cap thoff field")

We have the goal of validating DODGY packets earlier in the stack,
so we might very well revert this fix in the future.
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Jason Wang <jasowang@redhat.com>
Reported-by: syzbot+9da69ebac7dddd804552@syzkaller.appspotmail.com
Acked-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

John Allen says:

====================
ibmvnic: Reset behavior fixes

This patchset fixes a number of issues related to ibmvnic reset uncovered
from testing new Power9 machines with Everglades adapters and the new
functionality to change mtu and other parameters in the driver.

Changes since v1:
-In patch 1/3, added the line to free the long term buffers before
allocating a new one. This change inadvertently uncovered the problem
that the number of queues can change after a failover as well. To fix
this, we check whether or not the number of queues has changed in
do_reset and if they have, we do a full release and init of the queues.
-In patch 1/3, added variables to the adapter struct to track how
many rx/tx pools have actually been allocated and modify the release
pools routines to use these values rather than the possibly incorrect
req_rx/tx_queues values.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In reset events in which our memory allocations need to be reallocated,
VPD data is being freed, but never reallocated. This can cause issues if
we later attempt to access that memory or reset and attempt to free the
memory. This patch moves the allocation of the VPD data to init_resources
so that it will be symmetrically freed during release resources.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we request an unsupported mtu value, the vnic server will suggest a
different value. Currently we take the suggested value without question
and login with that value. However, the behavior doesn't seem completely
sane as attempting to change the mtu to some specific value will change
the mtu to some completely different value most of the time. This patch
fixes the issue by logging in with the previously used mtu value and
printing an error message saying that the given mtu is unsupported.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using newer backing devices can cause the required padding at the end of
buffer as well as the number of queues to change after a failover.
Since we currently assume that these values never change, after a
failover to a backing device with different capabilities, we can get
errors from the vnic server, attempt to free long term buffers that are
no longer there, or not free long term buffers that should be freed.

This patch resolves the issue by checking whether any of these values
change, and if so perform the necessary re-allocations.
Signed-off-by: NJohn Allen <jallen@linux.vnet.ibm.com>
Reviewed-by: NNathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rds-tcp uses m_ack_seq to track the tcp ack# that indicates
that the peer has received a rds_message. The m_ack_seq is
used in rds_tcp_is_acked() to figure out when it is safe to
drop the rds_message from the RDS retransmit queue.

The m_ack_seq must be calculated as an offset from the right
edge of the in-flight tcp buffer, i.e., it should be based on
the ->write_seq, not the ->snd_nxt.
Signed-off-by: NSowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

That a kevent could not be scheduled is not an error.
Such handlers must be able to deal with multiple events anyway.
As the successful scheduling of a work is a debug event, make
the failure debug priority, too.

V2: coding style
Signed-off-by: NOliver Neukum <oneukum@suse.com>
Reported-by: NCristian Caravena <caravena@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Daniel Borkmann says:

====================
pull-request: bpf 2018-01-18

The following pull-request contains BPF updates for your *net* tree.

The main changes are:

1) Fix a divide by zero due to wrong if (src_reg == 0) check in
   64-bit mode. Properly handle this in interpreter and mask it
   also generically in verifier to guard against similar checks
   in JITs, from Eric and Alexei.

2) Fix a bug in arm64 JIT when tail calls are involved and progs
   have different stack sizes, from Daniel.

3) Reject stores into BPF context that are not expected BPF_STX |
   BPF_MEM variant, from Daniel.

4) Mark dst reg as unknown on {s,u}bounds adjustments when the
   src reg has derived bounds from dead branches, from Daniel.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't change endianness when assigning vlan value in cxgb4_tc_flower
code when processing flow match parameters. The value gets converted
to network order as part of filtering code in set_filter_wr.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For ethtype_key = ETH_P_IPV6, set filter type as 1 in cxgb4_tc_flower
code when processing flow match parameters.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new helper would check if the pfn belongs to the page. For huge
pages it checks if the PFN is within range covered by the huge page.

The helper is used in check_pte(). The original code the helper replaces
had two call to page_to_pfn(). page_to_pfn() is relatively costly.

Although current GCC is able to optimize code to have one call, it's
better to do this explicitly.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Tetsuo reported random crashes under memory pressure on 32-bit x86
system and tracked down to change that introduced
page_vma_mapped_walk().

The root cause of the issue is the faulty pointer math in check_pte().
As ->pte may point to an arbitrary page we have to check that they are
belong to the section before doing math. Otherwise it may lead to weird
results.

It wasn't noticed until now as mem_map[] is virtually contiguous on
flatmem or vmemmap sparsemem. Pointer arithmetic just works against all
'struct page' pointers. But with classic sparsemem, it doesn't because
each section memap is allocated separately and so consecutive pfns
crossing two sections might have struct pages at completely unrelated
addresses.

Let's restructure code a bit and replace pointer arithmetic with
operations on pfns.
Signed-off-by: NKirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-and-tested-by: NTetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Acked-by: NMichal Hocko <mhocko@suse.com>
Fixes: ace71a19 ("mm: introduce page_vma_mapped_walk()")
Cc: stable@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>