Add the MINI2440 to the list of machines built by the
central defconfig.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit 52da219e added IIS
platform devices, but these do not build on s3c24xx systems
and the file depends on SND_S3C24XX_SOC, which is selected
for all S3C64XX/S3C24XX systems.

As a quick fix, make the dev-audio.o file depends on
SND_S3C64XX_SOC_I2S instead.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Commit 52da219e removed
the s3c_device_iis, but didn't replace it with anything
so a number of s3c24xx machines are currently failing
to build.

As a temporary fix, re-instate s3c_device_iis until a
proper replacement can be done for it.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove duplicated #include('s) in
  arch/arm/mach-s3c2440/mach-mini2440.c
Signed-off-by: NHuang Weiyi <weiyi.huang@gmail.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The commit ec976d6e
removed a number of gpio definitions from <mach/hardware.h>
but misssed updating these two files:

Fix the following build errors by including <linux/gpio.h>:
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c: In function 's3c24xx_spi_gpiocfg_bus1_gpg5_6_7':
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus1-gpg5_6_7.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c: In function 's3c24xx_spi_gpiocfg_bus0_gpe11_12_13':
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:25: error: implicit declaration of function 's3c2410_gpio_cfgpin'
arch/arm/plat-s3c24xx/spi-bus0-gpe11_12_13.c:28: error: implicit declaration of function 's3c2410_gpio_pullup'
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

Remove the unused CONFIG_DEBUG_S3C_PORT as we currently only have
support for using the S3C UARTs via the low-level debug code.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

CONFIG_S3C24XX_PWM was defined in arch/arm/plat-s3c24xx/Kconfig but
not used anywhere else as the corresponding makefile used
CONFIG_HAVE_PWM (selected by CONFIG_S3C24XX_PWM) to compile the PWM
driver.

Change the makefile to use CONFIG_S3C24XX_PWM to compile this driver
to ensure it is only build when needed.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The recent deprecation of dma_sync_{sg,single} ironically broke Blackfin
systems.  This is because we don't define dma_sync_sg_for_cpu at all, so
until the DMA asm-generic conversion/cleanup is done after the next
release, simply stub out the dma_sync_sg_for_{cpu,device} functions.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We don't support the BF535 at all, and the exception 0x2A text specific to
it is pretty verbose and confusing (since the behavior is simply odd), so
punt it to keep the noise down.
Signed-off-by: NYi Li <yi.li@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Make sure we process the kernel command line before poking the hardware,
so that we can process early printk.  This helps ensure that if you boot
a kernel configured for a different processor, something will be left in
the log buffer.
Signed-off-by: NRobin Getz <robin.getz@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The GPTMR0_CLOCKSOURCE Kconfig option requires the gptimers framework, so
make sure it is selected when this option is enabled.
Reported-by: NPeter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The port1 disable stuff was dropped from the USB ISP1760, so update the
Blackfin boards accordingly.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF526-EZBRD changed SDRAM chips between board revisions, so create a
timing table that can accommodate both.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We defined SDRAM_tRAS to TRAS_4, but then wrongly defined SDRAM_tRAS_num
to 3.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Many aspects of the Blackfin memory map is exactly the same across all
variants.  Rather than copy and paste all of these duplicated values in
each header, unify all of these into the common Blackfin memory map header
file.  In the process, push down BF561 SMP specific stuff to the BF561
specific header to keep the noise down.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Rather than use "Linux" in the boot image name (as this is redundant --
the image type is already set to "linux"), use the CPU name.  This makes
it fairly obvious when a wrong image is accidentally booted.  Otherwise
there is no kernel output and you waste time scratching your head
wondering wtf just happened.
Signed-off-by: NRobin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The current cache options don't really represent the hardware features.
They end up setting different aspects of the hardware so that the end
result is to turn on/off the cache.  Unfortunately, when we hit cache
problems with the hardware, it's difficult to test different settings to
root cause the problem.  The current settings also don't cleanly allow for
different caching behaviors with different regions of memory.

So split the configure options such that they properly reflect the settings
that are applied to the hardware.
Signed-off-by: NJie Zhang <jie.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NPhilippe Gerum <rpm@xenomai.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NPhilippe Gerum <rpm@xenomai.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NPhilippe Gerum <rpm@xenomai.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NPhilippe Gerum <rpm@xenomai.org>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Now that 0.1 of the BF51x is coming out, allow people to build for it.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF526-EZBRD has a SST SPI flash on it, not a ST Micro.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

We read the SWRST (Software Reset) register to get at the last reset
state, and then we may configure the DOUBLE_FAULT bit to control behavior
when a double fault occurs.  But if the lower bits of the register is
already set (like UART boot mode on a BF54x), we inadvertently make the
system reset by writing to the SYSTEM_RESET field at the same time.  So
make sure the lower 4 bits are always cleared.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Split out the optional IRQ14 lowering code to further simplify the
asm_do_IRQ() function and keep the ifdef nest under control.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Take a page from x86 and abstract the stack checking out of the
asm_do_IRQ() function so that the result is easier to digest.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Signed-off-by: NMike Frysinger <vapier@gentoo.org>

With the common IRQ code initializing much more of the irq_desc state, we
can't blindly initialize it ourselves to the local bad_irq state.  If we
do, we end up wrongly clobbering many fields.  So punt most of the bad irq
code as the common layers will handle the default state, and simply call
handle_bad_irq() directly when the IRQ we are processing is invalid.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

Update anomaly headers to match latest released anomaly sheets.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The BF533-EZKIT has two Flash In-System Programming devices hooked up to
the async memory bus, so add resources for the primary flashes and the
SRAMs on the devices.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The common DSA code changed structure layout, so update the BF518F-EZBRD
resources accordingly.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

The kgdb (in multiple places) and traps code developed pretty much
identical checks for how to access different regions of the Blackfin
memory map, but each wasn't 100%, so unify them to avoid duplication,
bitrot, and bugs with edge cases.
Signed-off-by: NMike Frysinger <vapier@gentoo.org>

pm_idle is used by infrastructure (eg, cpuidle) which expects architectures
to call it in a certain way.  Arrange for ARM to follow x86's lead on this
and call pm_idle() with interrupts already disabled.  However, we expect
pm_idle() to enable interrupts before it returns.

Also, OMAP wants to be able to disable hlt-ing, so allow hlt_counter to
prevent all calls to pm_idle.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the MN10300 vmlinux ldscript.  It needs to use various macros from
asm-generic/vmlinux.lds.h to correctly include all that it needs to.
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fix gpio-config off-by-one bug. Without this patch, touching GPA0 pin on
S3C64XX platform causes kernel oops.
Reviewed-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

N group

Add to_irq() function to onvert gpio to irq for external interrupt
group (GPN).
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

The usb-host clock was using the wrong define (the SCLK enable for the
usb-host-bus) to change the HCLK register instead of the HCLK_UHOST bit.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>

A few typos seems to have sneaked into the HCLK gate defines, causing the
usb host clock to not get enabled. Fix them according to the reference
manual and throw in the 3d accel bit for good measure.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NBen Dooks <ben-linux@fluff.org>