Currently qe_bd_t is used in the macro call -- dma_unmap_single,
which is a no-op on PPC32, thus error is hidden today. Starting
with 2.6.24, macro will be replaced by the empty static function,
and erroneous use of qe_bd_t will trigger compilation error.
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Reported by Corey Minyard <cminyard@mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A crash upon booting that is caused by bcm43xx has been reported [1] and
found to be due to a work queue being reinitialized while work on that
queue is still pending. This fix modifies the shutdown of work queues and
prevents periodic work from being requeued during shutdown. With this patch,
no more crashes on reboot were observed by the original reporter. I do not
get that particular failure on my system; however, when running a large
number of ifdown/ifup sequences, my system would kernel panic with the
'caps lock' light blinking at roughly a 1 Hz rate. In addition, there were
infrequent failures in the firmware that resulted in 'IRQ READY TIMEOUT'
errors. With this patch, no more of the first type of failure occur, and
incidence of the second type is greatly reduced.

[1] http://bugzilla.kernel.org/show_bug.cgi?id=8937Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch solves a problem that the spidernet driver sometimes fails
to handle IRQ.

The problem happens because,
- In Cell architecture, interrupts may arrive at an interrupt
  controller, even if they are masked by the setting on registers of
  devices. It happens when interrupt packets are sent just before
  the interrupts are masked.
- spidernet interrupt handler compares interrupt reasons with
  interrupt masks, so when such interrupts occurs, spidernet interrupt
  handler returns IRQ_NONE.
- When all of interrupt handler return IRQ_NONE, linux kernel disables
  the IRQ and it no longer delivers interrupts to the interrupt handlers.

spidernet doesn't work after above sequence, because it can't receive
interrupts.

This patch changes spidernet interrupt handler that it compares
interrupt reason with SPIDER_NET_INTX_MASK_VALUE.
Signed-off-by: NKou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update last_rx in registered device struct instead of
in the dummy device.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Introduces a module parameter to decide whether the physical
port link state is propagated to the network stack or not.
It makes sense not to take the physical port state into account
on machines with more logical partitions that communicate
with each other. This is always possible no matter what the physical
port state is. Thus eHEA can be considered as a switch there.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Lock debugging finds a problem in phy.c and phy_device.c,
this patch fixes it. Tested on an AT91SAM9263-EK board,
kernel 2.6.23-rc4.
Signed-off-by: NHans J. Koch <hjk@linutronix.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Need to restore multicast settings on resume and after 'ethtool -r'.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

64-bit DMA causes data corruption with atl1.  We don't know why, and Atheros
is working on it.  For now, just use 32-bit DMA.  This is a big hack that is
probably wrong, but it stops the bleeding.
Signed-off-by: NLuca Tettamanti <kronos.it@gmail.com>
Acked-by: NChris Snook <csnook@redhat.com>
Acked-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

A hardware bug was revealed after a recent PCI MSI patch was made to
always disable legacy INTX when enabling MSI.  The 5714/5780 chips
will not generate MSI when INTX is disabled, causing MSI failure
messages to be reported, and another patch was made to workaround the
problem by disabling MSI on ServerWorks HT1000 bridge chips commonly
found with the 5714.

We workaround this chip bug by enabling INTX after we enable MSI and
after we resume from suspend.

Update version to 3.81.

This problem was discovered by David Miller.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Acked-by: NAndy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Load the engine microcode when an interface
is brought up, instead of of doing it when the module
is loaded.
Loosen up tight binding between the driver and the
engine microcode version.
There is no need for microcode update with T3A boards.
Fix the file naming.
Do a better job at logging the loading activity.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

cxgb3 used netdev_priv() and dev->priv for different purposes.
In 2.6.23, netdev_priv() == dev->priv, cxgb3 needs a fix.
This patch is a partial backport of Dave Miller's changes in the
net-2.6.24 git branch.

Without this fix, cxgb3 crashes on 2.6.23.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes two problems during driver unload. The pci_disable_device()
call is before firmware reload, causing reads and writes across PCI bus after
disabling device. Second problem is the register window was wrong during
firmware reload

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Loading firmware during PCI probe can lead to incorrect initialization,
rendering the card unusable until next reboot.  This was introduced a while
ago as a workaround for firmware bug, a better workaround was submitted for
this a while ago. So removing original hack that loads firmware during probe.

Signed-off by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix the bug that 'ifconfig eth0 down' would hang up, reported by Stefan
Assmann <sassmann@suse.de>.
As we removed netif_poll_enable() from dev->open(), we should not use
netif_poll_disable() in dev->stop().
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The IOC3 driver's UART detection bits used to rely on the the firmware
setting the UART pre-divider in a way that's apropriate for the 8250
driver which doesn't currently program this register.  This happens
to work for the console but not rarely for additional ports.

While at it, also program the UART to RS-232 PIO mode; it the UART might
have been in mac-serial and/or DMA mode though that hasn't actually been
observed in practice.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add comment to explain why we cannot read back after chip reset
before delaying.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2.c (incorrectly) sets current->state directly to
TASK_UNINTERRUPTIBLE, without going through set_task_state(). However
all the code wants to do is an msleep so just make it do that instead...
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Acked-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The general kernel memory allocation functions return void pointers
and there is no need to cast their return values.
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

kmalloc() returns a void pointer, so there is no need to cast it in
 drivers/net/irda/kingsun-sir.c::kingsun_probe().
Signed-off-by: NJesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function declared static in forward declaration, but not in actual code.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

More noodlin on long flights, patch bin. Sparse warning fix for eql.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update myri10ge driver version to 1.3.2-1.269.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Based on a patch from Peter Oruba, convert myri10ge to use pcie_get_readrq()
and pcie_set_readrq() instead of our own PCI calls and arithmetics.

These driver changes incorporate the proposed PCI-X / PCI-Express read byte
count interface.  Reading and setting those values doesn't take place
"manually", instead wrapping functions are called to allow quirks for some
PCI bridges.
Signed-off-by: NBrice Goglin <brice@myri.com>
Signed-off by: Peter Oruba <peter.oruba@amd.com>
Based on work by Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Includes hcp_epas_dtor in eq/cq/qp destructors to unmap
HW register.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Update the module parameter description of "use_mcs" to
show correct default value
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Userspace DLPAR tool expects decimal numbers to be written to
and read from sysfs entries.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The driver remove method needs to return an int not void.  This was just
never noticed because usually this driver is not being built as a module.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mark new version to track if current driver is in use.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This fixes the extra timer overhead that people were whining about
as a 2.6.23 regression.

Running the watchdog timer all the time is unneeded. Change it
to run only if link is up, and reduce frequency to save power.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make sure PCI register for PHY power gets cleared on boot, and make
sure to avoid any PCI posting problems.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When transferring data at full speed, the DM9000 network interface
sometimes stops sending/receiving data. Worse, ksoftirqd consumes
100% cpu and the net tx watchdog never triggers.
Fix by spin_lock_irqsave() in dm9000_start_xmit() to prevent the
interrupt handler from interfering.
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Writing BMCR_RESET bit will reset MII_BMCR to default values. This is
clearly not what we want.
Signed-off-by: NDomen Puncer <domen.puncer@telargo.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

IP32 doesn't even have a ZONE_DMA so no point in using GFP_DMA in any
IP32-specific device driver.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

As noticed by Chuck Ebbert, commit c5e3ae88
introduced a copy-paste typo, as realtek phy is 0x732 and not 0x1c1. Obvious
fix below suggested by Ayaz Abdulla.
Signed-off-by: NWilly Tarreau <w@1wt.eu>
Cc: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch addresses the issue with "osize too small" errors in mppe
encryption.  The patch fixes the issue with wrong output buffer size
being passed to ppp decompression routine.

--------------------
As pointed out by Suresh Mahalingam, the issue addressed by
ppp-fix-osize-too-small-errors-when-decoding patch is not fully resolved yet.
The size of allocated output buffer is correct, however it size passed to
ppp->rcomp->decompress in ppp_generic.c if wrong. The patch fixes that.
--------------------
Signed-off-by: NKonstantin Sharlaimov <konstantin.sharlaimov@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ.  It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.

This patch moves the printk's out of the spinlock protected area.

Without this patch the machine hangs hard.  With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: NTimo Jantunen <jeti@iki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited MACINTOSH_DRIVERS per Geert Uytterhoeven's remark)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch adds support for 2 new board variants:
- A Quad port fiber 82571 board
- A blade version of the 82571 quad copper board
Signed-off-by: NAuke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>