Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 11 5月, 2017 1 次提交
  3. 26 4月, 2017 1 次提交
  5. 20 4月, 2017 1 次提交
    • J
      HID: wacom: Override incorrect logical maximum contact identifier · 6f107fab
      由 Jason Gerecke 提交于 
      It apears that devices designed around Wacom's G11 chipset (e.g. Lenovo
ThinkPad Yoga 260, Lenovo ThinkPad X1 Yoga, Dell XPS 12 9250, Dell Venue
8 Pro 5855, etc.) suffer from a common issue in their HID descriptors.
The logical maximum is not updated for the "Contact Identifier" usage,
leaving it as just "1" despite these devices being capable of tracking
far more touches.

Commit 60a22186 began ignoring usages with out-of-range values,
causing problems for devices based on this chipset. Touches after
the first will have an out-of-range Contact Identifier, and ignoring
that usage will cause the kernel to incorrectly slot each finger's
events (along with all the knock-on userspace effects that entails).

This commit checks for these buggy descriptors and updates the maximum
where required. Prior chipsets have used "255" as the maximum (and the
G11, at least, doesn't seem to actually use IDs outside the range of
1..CONTACTMAX) so continue using this value.

Cc: stable@vger.kernel.org
Fixes: 60a22186 ("HID: wacom: generic: add support for touchring")
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
      6f107fab
  7. 19 4月, 2017 1 次提交
    • J
      HID: wacom: Treat HID_DG_TOOLSERIALNUMBER as unsigned · 286f3f47
      由 Jason Gerecke 提交于 
      Because HID_DG_TOOLSERIALNUMBER doesn't first cast the value recieved from HID
to an unsigned type, sign-extension rules can cause the value of
wacom_wac->serial[0] to inadvertently wind up with all 32 of its highest bits
set if the highest bit of "value" was set.

This can cause problems for Tablet PC devices which use AES sensors and the
xf86-input-wacom userspace driver. It is not uncommon for AES sensors to send a
serial number of '0' while the pen is entering or leaving proximity. The
xf86-input-wacom driver ignores events with a serial number of '0' since it
cannot match them up to an in-use tool.  To ensure the xf86-input-wacom driver
does not ignore the final out-of-proximity event, the kernel does not send
MSC_SERIAL events when the value of wacom_wac->serial[0] is '0'. If the highest
bit of HID_DG_TOOLSERIALNUMBER is set by an in-prox pen which later leaves
proximity and sends a '0' for HID_DG_TOOLSERIALNUMBER, then only the lowest 32
bits of wacom_wac->serial[0] are actually cleared, causing the kernel to send
an MSC_SERIAL event. Since the 'input_event' function takes an 'int' as
argument, only those lowest (now-cleared) 32 bits of wacom_wac->serial[0] are
sent to userspace, causing xf86-input-wacom to ignore the event. If the event
was the final out-of-prox event, then xf86-input-wacom may remain in a state
where it believes the pen is in proximity and refuses to allow other devices
under its control (e.g. the touchscreen) to move the cursor.

It should be noted that EMR devices and devices which use both the
HID_DG_TOOLSERIALNUMBER and WACOM_HID_WD_SERIALHI usages (in that order) would
be immune to this issue. It appears only AES devices are affected.

Fixes: f85c9dc6 ("HID: wacom: generic: Support tool ID and additional tool types")
Cc: stable@vger.kernel.org
Signed-off-by: NJason Gerecke <jason.gerecke@wacom.com>
Acked-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
      286f3f47
  9. 13 4月, 2017 1 次提交
    • C
      HID: asus: support backlight on USB keyboards · af22a610
      由 Carlo Caione 提交于 
      The latest USB keyboards shipped on several ASUS laptop models
(including ROG laptop models such as GL702VMK) have the keyboards
backlight controlled by the keyboard firmware.

The firmware implements at least 3 different commands:
- Init command (to use when the system starts)
- Configuration command (to get keyboard status/information)
- Backlight level control (to change the level of the keyboard light)

With this patch we create the usual 'asus::kbd_backlight' led class
entry to control the keyboard backlight.

[jkosina@suse.cz: remove pointless cancel_work_sync() call while
 handling an error in asus_kbd_register_leds(), as spotted by
 Benjamin]
Signed-off-by: NCarlo Caione <carlo@endlessm.com>
Reviewed-by: NBenjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>
      af22a610
  11. 11 4月, 2017 1 次提交
  13. 06 4月, 2017 29 次提交
  15. 30 3月, 2017 5 次提交