Commit dbbf1755 "iwlwifi: use
antenna information in EEPROM" caused 4965 device breakage with
"Microcode SW error detected.  Restarting 0x82000000." message.
This patch reverts 4965 part of that commit.
Signed-off-by: NStanislaw Gruszka <sgruszka@redhat.com>
Acked-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove a superfluous ieee80211_is_data check as that was checked a few
lines before already and we wont't get here for non-data frames at all.

Second, the frame was already converted to 802.3 header format and
reading the fc and addr1 fields was only possible because the 802.3
header is short enough and didn't overwrite the relevant parts of the
802.11 header. Make the code more obvious by checking the ethernet
header's h_dest field.

Furthermore reorder the conditions to reduce the number of checks
when dynamic powersave is not needed (AP mode for example).
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Reviewed-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.

To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone().  For the rt2800pci special case a driver
flag is introduced.
Signed-off-by: NJohannes Stezenbach <js@sig21.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * A diff between rfbuffer settings of turbo and non-turbo
 modes indicates there is a bit on bank 2 related to turbo operation
 (it's set on turbo modes). This bit is present on all radios except
 RF5413 that seems to have a completely different bank 2. Also
 since 2317 has the same rf-registers locations with 2425 and
 since the bit exists on 2317 I assume it also exists on 2425/2417).
 So in case we use turbo mode (40MHz) enable it on bank modification.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Clean up what's left of turbo mode, since we handle all
 register modifications (rfbuffer comes next) on code there
 is no need to have duplicated arrays.

 * Rename change_channel to skip_pcu on initvals.c as we did
 on reset.c
Signed-off-by: NNick Kossifidis <micklfemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Clean up CHANNEL_T(URBO), use AR5K_BWMODE_40MHZ instead
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Use correct clock value when setting OFDM timings on
 non-default bwmodes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Don't return -EINVAL when trying to set tx power
 on RF5110 because AR5210 reset will fail. We need to
 add support for RF5110 and AR5210 eeprom in the future
 but for now just skip it.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since we set antenna flags on phy init and ack bitrate
 mode on pcu init, there is no need to save/restore sta_id
 flags on ath5k_hw_reset. Also we don't need to re-set our
 mac address because it's not affected by resets.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add synth-only channel change for AR2413/5413. When we call
 ath5k_reset with a channel ath5k_hw_reset will first try to
 set channel on PHY while PHY is running instead of doing a normal
 full reset. To do this phy_init has to change to implement this
 functionality.

 * Clean up change_channel flag, what it really did was skip PCU
 registers when setting initvals. This is done because on reset
 PCU registers are not affected (except the registers we set
 in pcu init and -due to hw problems- TSF). Use a new skip_pcu
 flag that's not misleading instead. In the future we might use
 that to also skip PCU reset and save us the TSF etc problems
 (needs testing because standard practice is to reset everything).

 * Use fast channel change only when setting channel, and set skip_pcu
 to false only on init. When we reset the card due to DMA or PHY
 problems skip pcu but never do a fast channel change.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Only set power table if we are changing channel/mode
 there is no need to recalculate and reset the power table
 all the time.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Set correct PLL settings for each bwmode
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Tweak power detector delays on AR5111/AR5112 when
 using half/quarter modes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Make sure we always set IFS timings even if no
 coverage class is set. If we don't we'll miss the
 needed changes for different bwmodes.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Set AR5K_DCU_GBL_IFS_MISC_TURBO_MODE flag on DCU when operating
 on 40MHz
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Replace set_slot_time with set_ifs_intervals that also sets
 the various inter-frame space intervals based on current bwmode.

 * Clean up AR5210 mess from reset_tx_queue, AR5210 only has one
 data queue and we set IFS intervals for that queue on set_ifs_intervals
 so there is nothing left to do for 5210 on reset_tx_queue.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Extend ieee80211_generic_frame_duration to support the various
 bwmodes.

 * Better document what's going on with ack bitrates and update
 write_rate_duration to support the standard ack bitrates (when
 we don't set the high bit).

 * Get rid of set_ack_bitrate_high and introduce a flag on ath5k_hw
 for this (we only called the function on init anyway so there is no
 difference).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Extend get_default_sifs/slot_time to include timings for turbo
 half and quarter rate modes.

 * AR5210 code for now uses timings already on core clock units
 instead of usecs so rename them (we 'll clean it up later).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Move setting of tx retry limits on a separate function
 (we 'll clean up this AR5210 mess later)
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * On turbo mode increase PHY settling times, note that
 we only increase switch settling time on AR5212 as indicated
 by initvals.

 * A few cleanups: Move frame control settings for AR5210 from
 reset_tx_queue to tweak_initvals and remove phy_scal settings
 from tweak_initvals (we tweak them alread on set_sleep_clock).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Now that we properly set rx/tx latencies for AR5311 remove
 that old buggy part of code left inside ath5k_hw_tweak_initval_settings
 that was never executed (you can't have an RF5112 radio on a mac older
 than AR5212). Also use a magic value for 5311 PHY_SCAL value.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Handle all usec parameters in one function. It's much cleaner
 this way.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Prepare for half/quarter/turbo support, introduce a new
 ah_bwmode parameter and get rid of ah_turbo. Bwmode stands
 for "bandwidth mode" and can have 4 values, default (20MHz),
 turbo (40MHz), half rate (10MHz), and quarter rate (5MHz).
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since we only use ath5k_hw_stop_tx_dma to stop the beacon
 queue, introduce a new function ath5k_hw_stop_beacon_queue so
 that we can use that instead and have better control. In the future
 we can add more beacon queue specific stuff there (maybe tweak
 beacon timers or something), for now just call ath5k_hw_stop_tx_dma.

 * Also since we don't call ath5k_hw_stop_rx/tx_dma from outside
 dma.c, make them static.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Make sure we are not trying to set RXDP while RX is active,
 for now ignore the return value.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * DCU early termination should be used to quickly flush QCU
 according to docs so don't enable it for all queues, enable
 it only when stopping each queue and disable it when we are
 done.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Increase timeouts on ath5k_hw_stop_tx_dma and also wait for
 tx queue to stop before checking for pending frames

 * Add a new debug level to debug dma start/stop
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Since we stop rx/tx dma and pcu durring reset there is no need to
 call ath5k_hw_stop_rx/tx_dma before, also there is no need to call
 them durring stop_locked since we can use ath5k_hw_dma_stop for
 both.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Stop PCU receive logic (DRU) durring reset
 We need to be sure pcu is not active when trying to stop rx dma
 right now this is done on ath5k_reset (base.c) but later we are
 going to clean it up.
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * Add a new function to stop rx/tx dma and use in when reset starts
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

 * No functional changes

 * Clean up reset:
 Introduce init functions for each unit and call them instead
 of having everything inside ath5k_hw_reset (it's just c/p for
 now so nothing changes except calling order -I tested it with
 various cards and it's ok-)

 * Further cleanups:
 ofdm_timings belongs to phy.c
 rate_duration belongs to pcu.c
 clock functions are general and belong to reset.c (more to follow)

 * Reorder functions for better organization:
 We start with helpers and other functions follow in categories,
 init functions are last
Signed-off-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.

This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).

Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The RX aggregation locking documentation was
wrong, which led Christian to also code the
timer timeout handling for it somewhat wrongly.

Fix the documentation, the two places that
need to hold the reorder lock across accesses
to the structure, and the debugfs code that
should just use RCU.

Also, remove acquiring the sta->lock across
reorder timeouts since it isn't necessary, and
change a few places to GFP_KERNEL because the
code path here doesn't need atomic allocations
as I noticed when reviewing all this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The recent tx path cleanups moved the software retry count tracking
from the ath_buf to the skb cb, however the actual counter update
referred to the wrong location, confusing block-ack window tracking.
Fix this by using the retries counter in the struct ath_frame_info.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This reverts commit 446fad5a.

The change had broken the packet injection on monitoring mode.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is not ideal to enable btcoex based on subsys id as it is
not unique, they are so random. It is also a pain keeping
all of them in a table to enable btcoex for a particular
hw. Going back to the old idea.
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This implements the new off-channel TX API
in mac80211 with a new work item type. The
operation doesn't add a new work item when
we're on the right channel and there's no
wait time so that for example p2p probe
responses will be transmitted without delay.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>