for both mixed and pure 40MHz, need to check for valid channel location.
if the specified channel not allow the channel location requested
(ABOVE, BELOW), then reject the Fat channel access

This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1988

("iwlwifi: checking for 40MHz mode" and "iwlwifi: check control channel
for pure 40MHz" combine with this to address the above bug. -- JWL)
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

for pure 40MHz mode, set the control channel location if provided, but not
like Mixed mode; if information is not provided, still allow 40MHz
operation.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

when checking for 40MHz, compare ht_protection to
IEEE80211_HT_OP_MODE_PROTECTION_20MHZ. ht_protection is not a bit-mask
field
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My earlier patch,
	"mac80211: unify config_interface and bss_info_changed"
introduced a bug in iwlwifi where it will do some things
incorrectly now when reassociating.

Revamp iwl_bss_info_changed to fix that issue and make it
easier to read. Also, while at it, add comments about things
that it should do but currently doesn't.

Finally, also improve the locking in the function.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

|BUG: spinlock recursion on CPU#0, lbs_spi_thread/1030
| lock: dee9a1bc, .magic: dead4ead, .owner: lbs_spi_thread/1030, .owner_cpu: 0
|Call Trace:
|[deec3eb0] [c0007220] show_stack+0x4c/0x15c (unreliable)
|[deec3ef0] [c0187720] spin_bug+0x9c/0xb0
|[deec3f10] [c0187890] _raw_spin_lock+0x54/0x148
|[deec3f40] [c02d260c] _spin_lock_irqsave+0x2c/0x44
|[deec3f60] [e8671800] lbs_queue_event+0x7c/0x130 [libertas]
|[deec3f80] [e8725f04] lbs_spi_thread+0x538/0x58c [libertas_spi]
|[deec3fe0] [c004f270] kthread+0x4c/0x88
|[deec3ff0] [c000f33c] kernel_thread+0x4c/0x68

if_spi_e2h() is grabbing ->driver_lock just while calling
lbs_queue_event() which is grabbing the same lock.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The card firmware does not set the Command Download Ready interrupt bit
when IEEE PS mode is enabled, preventing the driver from sending
commands (such as the command to exit IEEE PS mode) since there is no
indication that the card is ready to accept commands.

This patch works around the problem by using the the TX Download Ready
bit in place of the Command Download Ready Bit while in IEEE PS mode.
TX Download Ready is set in IEEE PS mode.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When the hard state changes, we shouldn't set the soft
state to blocked as well -- we have no such indication
from the device in that case so leave it untouched.

Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13458.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix recent fusion driver kernel-doc fatal error and warnings.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Eric.Moore@lsi.com
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.  This is the same bug that was reported in ib_mthca by Yinghai
Lu <yhlu.kernel@gmail.com>.
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

The current build shows a warning with the DTL-1 driver:

  CC [M]  drivers/bluetooth/dtl1_cs.o
drivers/bluetooth/dtl1_cs.c: In function ‘dtl1_hci_send_frame’:
drivers/bluetooth/dtl1_cs.c:396: warning: ‘nsh.type’ may be used uninitialized in this function

Fix this by adding a proper error for unknown packet types.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

menuconfig IEEE802154_DRIVERS is a bool that depends on tristate IEEE802154.
If the IEEE802154 symbol is 'm', the bool becomes 'y'.
This allows tristate symbols under IEEE802154_DRIVERS to be configured as
'y' and cause build problems.
Changing the menuconfig bool to a tristate fixes this.

drivers/built-in.o: In function `fake_scan_req':
fakehard.c:(.text+0x46d625): undefined reference to `ieee802154_nl_scan_confirm'
drivers/built-in.o: In function `fake_disassoc_req':
fakehard.c:(.text+0x46d66f): undefined reference to `ieee802154_nl_disassoc_confirm'
drivers/built-in.o: In function `fake_assoc_req':
fakehard.c:(.text+0x46d6be): undefined reference to `ieee802154_nl_assoc_confirm'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Acked-by: NSergey Lapin <slapin@ossfans.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to rework how bonding devices are initialized to make it more
amenable to creating bonding devices via netlink.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove bogus non-portable possibly unaligned way of testing
for zero addres..
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The bonding device acts unlike all other Linux network device functions
in that it ignores case of device names. The developer must have come
from windows!

Cleanup the management of names and use standard routines where possible.
Flag places where bonding device still doesn't work right with network
namespaces.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "expected_refcount" stuff in bonding sysfs module is a mistake.
Sysfs does proper refcounting, and it is okay to remove a bond device
that has some user process holding the file open.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Resolve some of the complaints from checkpatch, and remove "magic emacs format"
comments, and useless MODULE_SUPPORTED_DEVICE(). But should not
change actual code.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not safe to use a network device destructor that is a function in
the module, since it can be called after module is unloaded if sysfs
handle is open.

When eventually using netlink, the device cleanup code needs to be done
via uninit function.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The whole read/write semaphore locking can be removed. It doesn't add any
protection that isn't already done by using the RTNL mutex properly.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid a unnecessary carrier state transistion that happens when device
is registered.
Lockdep works better if initialization is done before registration as well.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bond_create() is always called with same parameters so move the argument
down.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When both MSI-X and legacy INTx fail to generate an interrupt, the
driver frees the MSI-X interrupts twice.  Fix this by clearing the
have_irq flag for the MSI-X interrupts when they are freed the first
time.
Reported-by: NYinghai Lu <yhlu.kernel@gmail.com>
Tested-by: NYinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

New revision of Atmel MCI interface adds new features. This is a update of
register definition in header file. This new MCI IP is called MCI2.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The MCI IP is shared among AVR32 and AT91 SOCs.
AT91 has specific bit definitions in the user interface of MCI SD/MMC IP.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Now tmio_mmc is able to drive the MMC/SD cell in ASIC3.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <spyro@f2s.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

In the write recovery routine, the data to get from the card
is allocated from the stack. The DMA mapping documentation says
explicitly stack memory is not mappable by any of the DMA calls.

Change to using kmalloc() to allocate the memory for the result
from the card and then free it once we've finished with the
transaction.

[ Changed to GFP_KERNEL allocation - Pierre Ossman ]
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

If using ADMA, then we should print the ADMA error
and current pointer in sdhci_dumpregs() when any
debug is requested.
Signed-off-by: NBen Dooks <ben@simtec.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This patch fixes the clock setup in tmio_mmc.

  * Incorrect divider setting
  * Cruft written to the clock registers (seemingly harmless but Not
Good (tm))

It also eliminates some unnecessary ifs and tidies the loop syntax.

Thanks to Philipp Zabel who discovered the divider issue, commenting

   "Except for the SDCLK = HCLK (divider bypassed) case, the clock
    setting resulted in double the requested frequency.
    The smallest possible frequency (f_max/512) is configured with
    a divider setting 0x80, not 0x40."
Signed-off-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

ASIC3 can disable the memory, so we need to wait for mfd_cell->enable
to enable the memory before we can map the SD control registers.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Use an IRQF_TRIGGER_ flag in request_irq instead.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Some ASIC3 devices in the wild are connected with the address bus shifted
by one line, so that its 16-bit registers appear 32-bit aligned in host
memory space.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The Toshiba parts all have a 24 MHz HCLK, but HTC ASIC3 has a 24.576 MHz HCLK
and AMD Imageon w228x's HCLK is 80 MHz. With this patch, the MFD driver
provides the HCLK frequency to tmio_mmc via mfd_cell->driver_data.
Signed-off-by: NPhilipp Zabel <philipp.zabel@gmail.com>
Acked-by: NIan Molton <ian@mnementh.co.uk>
Acked-by: NSamuel Ortiz <sameo@openedhand.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

This patch changes the reported error code for the responses
to a command from EINVAL to EFAULT/ENOSYS, as EINVAL is reserved
for non-recoverable host errors, and the responses from
the SD/MMC card may be because of recoverable transmission
errors in the command or in the response. Response codes
in SPI mode are NOT protected by a checksum, so don't trust them.
Signed-off-by: NWolfgang Muees <wolfgang.mues@auerswald.de>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Added a platform driver which uses the SDHCI core.
Signed-off-by: NRichard Röjfors <richard.rojfors.ext@mocean-labs.com>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The MMC core has now been fixed to not send silly frequencies to the
drivers which means we can remove this workaround.
Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

Signed-off-by: NPierre Ossman <pierre@ossman.eu>

The code is divided in two parts. There is a virtual 'bus' driver
that handles PCI device and registers three new devices one per card
reader type. The other driver handles SD/MMC part of the reader.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NPierre Ossman <pierre@ossman.eu>