Commit 7fa6f340 "AER revised" erroneously inserted an error-flow
in which a semaphore is released even though the attempt to take it
has failed.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

57712/578xx devices during handling of encapsulated TSO can
properly increase ip id for only one ip header.
The patch selects inner header to be increased.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
CC: Eilon Greenstein <eilong@broadcom.com>
CC: Ariel Elior <ariele@broadcom.com>
CC: Maciej Zenczykowski <maze@google.com>
CC: Jesse Gross <jesse@nicira.com>
Reported-by: NEric Dumazet <edumazet@google.com>
Tested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Revised bnx2x implementation of PCI Express Advanced Error Recovery -
stop and free driver resources according to the AER flow (instead of the
currently implemented `hope-for-the-best' release approach), and do not make
any assumptions on the HW state after slot reset.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch utilizes FW offload capabilities for
encapsulation protocols.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bnx2x FW 1.78.17 properly supports DCBX configuration for 4-port devices,
enabling FCoE support on 57840 boards.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update appropriate HSI files and adapt driver accordingly.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent bnx2x devices which are used mainly for storage from using zero
MAC addresses as their primary MAC address.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Support sysfs interface for getting the maximal number of virtual functions
   of a given physical function.
2. Support sysfs interface for getting and setting the current number of
   virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for iproute2 callbacks allowing querying a physical
function as to its child virtual functions, and setting the macs and vlans
of said virtual functions.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When using a chip operating in Single Function mode, when the chip is probed
the bnx2x would print a message warning of an unknown Multi Function mode.

This patch prevents said message.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In latest boards, the CHIP_METAL register contains an incorrect
revision value, so the correct one needs to be obtained in a
different manner.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual functions don't have access to HW registers, therefore most ethtool ops
are forbidden to them. Instead of checking in each op whether the device being
driven is a virtual function or a physical function, this patch creates a
separate ethtool ops struct for virtual functions and uses it to initialize
the ethtool ops of the driver in case it is driving a virtual function device.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In INTA mode, cnic and bnx2x share the same IRQ.  During chip reset,
for example, cnic will stop servicing IRQs after it has shutdown the
cnic hardware resources.  However, the shared IRQ is still active as
bnx2x needs to finish the reset.  There is a window when bnx2x does
not know that cnic is no longer handling IRQ and things don't always
work properly.

Add a flag to tell bnx2x that cnic is handling IRQ.  The flag is set
before the first cnic IRQ is expected and cleared when no more cnic
IRQs are expected, so there should be no race conditions.
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix an incorrect SR-IOV memory release which was committed in 1ab4434c.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove most of the sparse warnings in the bnx2x compilation
(i.e., thus resulting when compiling with `C=2 CF=-D__CHECK_ENDIAN__').
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add/Revise several debug prints in the bnx2x driver - on regular flows
as well as error flows.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change the incorrect usage of `usleep_range(1000, 1000)' into
`usleep_range(1000, 2000)'.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Slightly changes the bnx2x code without `true' functional changes.
Changes include:
 1. Gathering macros into a single macro when combination is used multiple
    times.
 2. Exporting parts of functions into their own functions.
 3. Return values after if-else instead of only on the else condition
    (where current flow would simply return same value later in the code)
 4. Removing some unnecessary code (either dead-code or incorrect conditions)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Mostly corrects white spaces, indentations, and comments.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling interrupts, acknowledge the interrupt only
after configuring the IGU to the correct interrupt mode
(otherwise it would dirty selftests)
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get better control over interrupts during panic, and allow FW to
test outgoing Tx packets when stop-on-error is allowed.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a device is configured to act as either iscsi or fcoe
device in its nvram, prevent the other from being misused by
preventing its activation in the driver.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current logic causes chips running in switch dependent multi-function
FCoE mode not to configure their MAC, leading to an all 0s MAC.

This patch configures the interface with the SAN Mac instead.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Self-tests following boot from SAN have failed as the
UNDI driver might leave some NIG interrupt indications.

This patch does the clean-up, clearing those indications
and allowing the test to pass.
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As part of the previous driver unload flow, whenever bnx2x is
loaded after the UNDI driver it closes all Rx traffic.
However, this leads to management traffic also being stopped until
the network interface associated with one of its functions gets loaded.

To remedy this, management traffic is re-opened once the 'cleaning'
after the previous driver ends.
Signed-off-by: NBarak Witkowski <barak@broadcom.com>
Signed-off-by: NYuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Static checkers complained that the E1H_FUNC_MAX define is used
incorrectly in bnx2x_pretend_func(). The complaint was justified,
although its not a real bug, as the first part of the conditional
protects us in this case (a real bug would happen if a VF tried to
use the pretend func, but there are no VFs in E1H chips).
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

perm_addr is initialized correctly in register_netdevice() so to init it in
drivers is no longer needed.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this patch the SR-IOV code is segregated from the main bulk of
the bnx2x code. The CONFIG_BNX2X_SRIOV define is added to Broadcom's
Kconfig, and allows the elision of the building of all the SR-IOV
support code in the driver.
The define is dependant on the kernel CONFIG_PCI_IOV configuration
define.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJorrit Schippers <jorrit@ncode.nl>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Add the various VF device ids (of all supported hardware)
Add the calls to enable_sriov and disable_sriov to enable the
SR-IOV feature. This patch also advances the version and release
date of the bnx2x module.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PF <-> VF Bulletin Board is a simple interface between the
PF and the VF. The main reason for the Bulletin Board is to allow
the PF to be the initiator. The VF publishes at 'acquire' stage
the GPA of a Bulletin Board structure it has allocated. The PF notes
this GPA in the VF database. The VF samples the Bulletin Board
periodically for new messages. The latest version of the BB is always
used.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FLR indication arrives as an attention from the management processor.
Upon VF flr all FLRed function in the indication have already been
released by Firmware and now we basically need to free the resources
allocated to those VFs, and clean any remainders from the device
(FLR final cleanup).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 'release' request is the opposite of the 'acquire' request.
At release, all the resources allocated to the VF are reclaimed.
The release flow applies the close flow if applicable.
Note that there are actually two types of release:
1. The VF has been removed, and so issued a 'release' request
over the VF <-> PF Channel.
2. The PF is going down and so has to release all of it's VFs.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Statistics are collected by the PF driver. The collection is
performed via a query sent to the device which is basically an array
of 3-tuples of the form (statistics client, function, DMAE address).
In this patch the PF driver adds to the query, on top of the
statistics clients it is maintaining for itself (rss queues, storage,
etc), the 3-tuples for the VFs it is maintaining. The addresses used
are the GPAs of the statistics buffers supplied by the VF in the
init message on the VF <-> PF channel. The function parameter
ensures that the iommu will translate the GPA to the correct physical
address.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VF driver will send an 'init' request as part of its nic load
flow. This message is used by the VF to publish the GPA's of its
status blocks, slow path ring and statistics buffer.
The PF driver notes all this down in the VF database, and also uses
this message to transfer the VF to VF_INIT state internally.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Support interrupt from device which indicates VF has placed
A request on the VF <-> PF channel.
The PF driver issues a DMAE to retrieve the request from the VM
memory (the Ghost Physical Address of the request is contained
in the interrupt. The PF driver uses the GPA in the DMAE request,
which is translated by the IOMMU to the correct physical address).
The request which arrives is examined to recognize the sending VF.
The PF driver allocates a workitem to handle the VF Operation (vfop).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At nic load of the PF, if VFs may be present, prepare the device
for the VFs. Initialize the VF database in preparation of VF arrival.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When A PF determines that it may have to manage SRIOV VFs it
allocates a database for this purpose. The database is intended to
keep track of the VF state, the resources allocated for each VF
(queues, interrupt vectors, etc), the state of the VF's queues.
When the VF loads the database is updated accordingly.
When A VF closes the database is consulted to determine which
resources need to be released (close queues against device, reclaim
interrupt vectors, etc).
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VF driver is transmitting it must supply the correct mac
address in the parsing BD. This is used for firmware validation
and enforcement and also for tx-switching.
Refactor interrupt ack flow to allow for different BAR addresses of
the hardware in the PF BAR vs the VF BAR.
Signed-off-by: NAriel Elior <ariele@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>