Tail dropping is enabled for a port when:

1. A source port consumes more packet buffers than the watermark encoded
   in SYS:PORT:ATOP_CFG.ATOP.

AND

2. Total memory use exceeds the consumption watermark encoded in
   SYS:PAUSE_CFG:ATOP_TOT_CFG.

The unit of these watermarks is a 60 byte memory cell. That unit is
programmed properly into ATOP_TOT_CFG, but not into ATOP. Actually when
written into ATOP, it would get truncated and wrap around.

Fixes: a556c76a ("net: mscc: Add initial Ocelot switch support")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The IS2 IP4_TCP_UDP key offsets do not correspond to the VSC7514
datasheet. Whether they work or not is unknown to me. On VSC9959 and
VSC9953, with the same mistake and same discrepancy from the
documentation, tc-flower src_port and dst_port rules did not work, so I
am assuming the same is true here.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver was not unregistering its network interfaces on unbind.
Now it is.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mscc_ocelot_probe() is already pretty large and hard to follow. So move
the code for parsing ports in a separate function.

This makes it easier for the next patch to just call
mscc_ocelot_release_ports from the error path of mscc_ocelot_init_ports.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ocelot_init() allocates memory, resets the switch and polls for a status
register, things which can fail. Stop probing the driver in that case,
and propagate the error result.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do not proceed probing if we couldn't allocate memory for the ports
array, just error out.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
    with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.

This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb82 ("net: dsa: declare lockless TX feature for
slave ports").  So the logic of using and incrementing the timestamp id
should be atomic per port.

The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: NAlexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The TX-timestampable skb is added late to the ocelot_port->tx_skbs. It
is in a race with the TX timestamp IRQ, which checks that queue trying
to match the timestamp with the skb by the ts_id. The skb should be
added to the queue before the IRQ can fire.

Fixes: 4e3b0468 ("net: mscc: PTP Hardware Clock (PHC) support")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.

[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-throughSigned-off-by: NGustavo A. R. Silva <gustavoars@kernel.org>

The next hw timestamp should be snapshoot to the read registers
only once the current timestamp has been read.
If none of the pending skbs matches the current HW timestamp
just gracefully flush the available timestamp by reading it.
Signed-off-by: Nlaurent brando <laurent.brando@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC7514 is marketed as a 10-port switch, however it has 11 physical
ports (0->10) in the block diagram:
https://www.microsemi.com/product-directory/ethernet-switches/3992-vsc7514
(also in the device tree at arch/mips/boot/dts/mscc/ocelot.dtsi)

Additionally, by architecture it has one more entry in the analyzer
block, situated right after the physical ports, for the CPU port module.
This is not a physical port, it only represents a channel for frame
injection and extraction. That entry for the CPU port is at index 11 in
the analyzer.

When the register groups for QSYS_SWITCH_PORT_MODE, SYS_PORT_MODE and
SYS_PAUSE_CFG are declared to be replicated 11 times, the 11th entry in
the array of regfields is not initialized, so the CPU port module is not
initialized either.

The documentation of QSYS_SWITCH_PORT_MODE for VSC7514 also says that
this register group is replicated 12 times, so this patch is simply
reflecting that and not introducing any further inconsistency.

Fixes: 886e1387 ("net: mscc: ocelot: convert QSYS_SWITCH_PORT_MODE and SYS_PORT_MODE to regfields")
Fixes: 541132f0 ("net: mscc: ocelot: convert SYS_PAUSE_CFG register access to regfield")
Reported-by: NBryan Whitehead <bryan.whitehead@microchip.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For PPS output (perout period is 1.000000000), accept the new "phase"
parameter from the periodic output request structure.

For both PPS and freeform output, accept the new "on" argument for
specifying the duty cycle of the generated signal. Preserve the old
defaults for this "on" time: 1 us for PPS, and half the period for
freeform output.

Also preserve the old behavior that accepted the "phase" via the "start"
argument.
Signed-off-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NHoratiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having the users of MSCC_OCELOT_SWITCH_LIB depend on REGMAP_MMIO was a
bad idea, since that symbol is not user-selectable. So we should have
kept a 'select REGMAP_MMIO'.

When we do that, we run into 2 more problems:

- By depending on GENERIC_PHY, we are causing a recursive dependency.
  But it looks like GENERIC_PHY has no other dependencies, and other
  drivers select it, so we can select it too:

drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69:  symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68:  symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7:  symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15:   symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22:   symbol MSCC_OCELOT_SWITCH depends on GENERIC_PHY
drivers/phy/Kconfig:8:  symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:41:        symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:13:     symbol MDIO_BUS depends on MDIO_DEVICE
drivers/net/phy/Kconfig:6:      symbol MDIO_DEVICE is selected by PHYLIB
drivers/net/phy/Kconfig:254:    symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19:    symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25:    symbol ARC_EMAC depends on OF_IRQ

- By depending on PHYLIB, we are causing a recursive dependency. PHYLIB
  only has a single dependency, "depends on NETDEVICES", which we are
  already depending on, so we can again hack our way into conformance by
  turning the PHYLIB dependency into a select.

drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69:  symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68:  symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7:  symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15:   symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22:   symbol MSCC_OCELOT_SWITCH depends on PHYLIB
drivers/net/phy/Kconfig:254:    symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19:    symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25:    symbol ARC_EMAC depends on OF_IRQ

Fixes: f4d0323b ("net: mscc: ocelot: convert MSCC_OCELOT_SWITCH into a library")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

The ocelot_wm_encode function deals with setting thresholds for pause
frame start and stop. In Ocelot and Felix the register layout is the
same, but for Seville, it isn't. The easiest way to accommodate Seville
hardware configuration is to introduce a function pointer for setting
this up.
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Seville has a different bitwise layout than Ocelot and Felix.
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Ocelot switches do not support flow control on Ethernet interfaces
where a DSA tag must be added. If pause frames are enabled, they will be
encapsulated in the DSA tag just like regular frames, and the DSA master
will not recognize them.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't want ocelot_port_set_maxlen to enable pause frame TX, just to
adjust the pause thresholds.

Move the unconditional enabling of pause TX to ocelot_init_port. There
is no good place to put such setting because it shouldn't be
unconditional. But at the moment it is, we're not changing that.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently Felix and Ocelot share the same bit layout in these per-port
registers, but Seville does not. So we need reg_fields for that.

Actually since these are per-port registers, we need to also specify the
number of ports, and register size per port, and use the regmap API for
multiple ports.

There's a more subtle point to be made about the other 2 register
fields:
- QSYS_SWITCH_PORT_MODE_SCH_NEXT_CFG
- QSYS_SWITCH_PORT_MODE_INGRESS_DROP_MODE
which we are not writing any longer, for 2 reasons:
- Using the previous API (ocelot_write_rix), we were only writing 1 for
  Felix and Ocelot, which was their hardware-default value, and which
  there wasn't any intention in changing.
- In the case of SCH_NEXT_CFG, in fact Seville does not have this
  register field at all, and therefore, if we want to have common code
  we would be required to not write to it.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the register definitions for the MSCC MIIM MDIO controller in
preparation for seville_vsc9959.c to create its accessors for the
internal MDIO bus.

Since we've introduced elements to ocelot_regfields that are not
instantiated by felix and ocelot, we need to define the size of the
regfields arrays explicitly, otherwise ocelot_regfields_init, which
iterates up to REGFIELD_MAX, will fault on the undefined regfield
entries (if we're lucky).
Signed-off-by: NMaxim Kochetkov <fido_max@inbox.ru>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the moment, there are some minimal register differences between
VSC7514 Ocelot and VSC9959 Felix. To be precise, the PCS1G registers are
missing from Felix because it was integrated with an NXP PCS.

But with VSC9953 Seville (not yet introduced), the register differences
are more pronounced.  The MAC registers are located at different offsets
within the DEV_GMII target. So we need to refactor the driver to keep a
regmap even for per-port registers. The callers of the ocelot_port_readl
and ocelot_port_writel were kept unchanged, only the implementation is
now more generic.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since 'tcfp_burst' with TICK factor, driver side always need to recover
it to the original value, this patch moves the generic calculation and
recover to the 'burst' original value before offloading to device driver.
Signed-off-by: NPo Liu <po.liu@nxp.com>
Acked-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that all net_device operations are bundled together inside
mscc_ocelot.ko and no longer part of the common library, there's no
reason to export these symbols.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current procedure for installing a multicast address is hardcoded
for IPv4. But, in the ocelot hardware, there are 3 different procedures
for IPv4, IPv6 and for regular L2 multicast.

For IPv6 (33-33-xx-xx-xx-xx), it's the same as for IPv4
(01-00-5e-xx-xx-xx), except that the destination port mask is stuffed
into first 2 bytes of the MAC address except into first 3 bytes.

For plain Ethernet multicast, there's no port-in-address stuffing going
on, instead the DEST_IDX (pointer to PGID) is used there, just as for
unicast. So we have to use one of the nonreserved multicast PGIDs that
the hardware has allocated for this purpose.

This patch classifies the type of multicast address based on its first
bytes, then redirects to one of the 3 different hardware procedures.

Note that this gives us a really better way of redirecting PTP frames
sent at 01-1b-19-00-00-00 to the CPU. Previously, Yangbo Lu tried to add
a trapping rule for PTP EtherType but got a lot of pushback:

https://patchwork.ozlabs.org/project/netdev/patch/20190813025214.18601-5-yangbo.lu@nxp.com/

But right now, that isn't needed at all. The application stack (ptp4l)
does this for the PTP multicast addresses it's interested in (which are
configurable, and include 01-1b-19-00-00-00):

	memset(&mreq, 0, sizeof(mreq));
	mreq.mr_ifindex = index;
	mreq.mr_type = PACKET_MR_MULTICAST;
	mreq.mr_alen = MAC_LEN;
	memcpy(mreq.mr_address, addr1, MAC_LEN);

	err1 = setsockopt(fd, SOL_PACKET, PACKET_ADD_MEMBERSHIP, &mreq,
			  sizeof(mreq));

Into the kernel, this translates into a dev_mc_add on the switch network
interfaces, and our drivers know that it means they should translate it
into a host MDB address (make the CPU port be the destination).
Previously, this was broken because all mdb addresses were treated as
IPv4 (which 01-1b-19-00-00-00 obviously is not).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current iterators are impossible to understand at first glance
without switching back and forth between the definitions and their
actual use in the for loops.

So introduce some convenience names to help readability.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds the mdb hooks in felix and exports the mdb functions from
ocelot.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When used in DSA mode (as seen in Felix), the DEST_IDX in the MAC table
should point to the PGID for the CPU port (PGID_CPU) and not for the
Ethernet port where the CPU queues are redirected to (also known as Node
Processor Interface - NPI).

Because for Felix this distinction shouldn't really matter (from DSA
perspective, the NPI port _is_ the CPU port), make the ocelot library
act upon the CPU port when NPI mode is enabled. This has no effect for
the mscc_ocelot driver for VSC7514, because that does not use NPI (and
ocelot->npi is -1).
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ocelot hardware designers have made some hacks to support multicast
IPv4 and IPv6 addresses. Normally, the MAC table matches on MAC
addresses and the destination ports are selected through the DEST_IDX
field of the respective MAC table entry. The DEST_IDX points to a Port
Group ID (PGID) which contains the bit mask of ports that frames should
be forwarded to. But there aren't a lot of PGIDs (only 80 or so) and
there are clearly many more IP multicast addresses than that, so it
doesn't scale to use this PGID mechanism, so something else was done.
Since the first portion of the MAC address is known, the hack they did
was to use a single PGID for _flooding_ unknown IPv4 multicast
(PGID_MCIPV4 == 62), but for known IP multicast, embed the destination
ports into the first 3 bytes of the MAC address recorded in the MAC
table.

The VSC7514 datasheet explains it like this:

    3.9.1.5 IPv4 Multicast Entries

    MAC table entries with the ENTRY_TYPE = 2 settings are interpreted
    as IPv4 multicast entries.
    IPv4 multicasts entries match IPv4 frames, which are classified to
    the specified VID, and which have DMAC = 0x01005Exxxxxx, where
    xxxxxx is the lower 24 bits of the MAC address in the entry.
    Instead of a lookup in the destination mask table (PGID), the
    destination set is programmed as part of the entry MAC address. This
    is shown in the following table.

    Table 78: IPv4 Multicast Destination Mask

        Destination Ports            Record Bit Field
        ---------------------------------------------
        Ports 10-0                   MAC[34-24]

    Example: All IPv4 multicast frames in VLAN 12 with MAC 01005E112233 are
    to be forwarded to ports 3, 8, and 9. This is done by inserting the
    following entry in the MAC table entry:
    VALID = 1
    VID = 12
    MAC = 0x000308112233
    ENTRY_TYPE = 2
    DEST_IDX = 0

But this procedure is not at all what's going on in the driver. In fact,
the code that embeds the ports into the MAC address looks like it hasn't
actually been tested. This patch applies the procedure described in the
datasheet.

Since there are many other fixes to be made around multicast forwarding
until it works properly, there is no real reason for this patch to be
backported to stable trees, or considered a real fix of something that
should have worked.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the function prototypes from ocelot_police.h and make these
functions static. We need to move them above their callers. Note that
moving the implementations to ocelot_police.c is not trivially possible
due to dependency on is2_entry_set() which is static to ocelot_vcap.c.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.
Let's rename the structures and functions to something more generic, so
that VCAP IS1 structures (which would otherwise have to be called
Ingress Classification Entries) can reuse the same code without
confusion.

Some renaming that was done:

struct ocelot_ace_rule -> struct ocelot_vcap_filter
struct ocelot_acl_block -> struct ocelot_vcap_block
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_vlan -> struct ocelot_vcap_key_vlan
enum ocelot_ace_action -> enum ocelot_vcap_action
struct ocelot_ace_stats -> struct ocelot_vcap_stats
enum ocelot_ace_type -> enum ocelot_vcap_key_type
struct ocelot_ace_frame_* -> struct ocelot_vcap_key_*

No functional change is intended.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Access Control Lists (and their respective Access Control Entries) are
specifically entries in the VCAP IS2, the security enforcement block,
according to the documentation.

Let's rename the files that deal with generic operations on the VCAP
TCAM, so that VCAP IS1 and ES0 can reuse the same code without
confusion.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ocelot hardware library shouldn't contain too much net_device
specific code, since it is shared with DSA which abstracts that
structure away. So much as much of this code as possible into the
mscc_ocelot driver and outside of the common library.

We're making an exception for MDB and LAG code. That is not yet exported
to DSA, but when it will, most of the code that's already in ocelot.c
will remain there. So, there's no point in moving code to ocelot_net.c
just to move it back later.

We could have moved all net_device code to ocelot_vsc7514.c directly,
but let's operate under the assumption that if a new switchdev ocelot
driver gets added, it'll define its SoC-specific stuff in a new
ocelot_vsc*.c file and it'll reuse the rest of the code.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ocelot_regs.c actually shouldn't be part of the common library. It
describes the register map of the VSC7514 switch. The way ocelot
switches work, they'll have highly optimized register maps, so another
SoC will likely have the same registers but laid out completely
different in memory (so there's little room for reusing this structure).
So move it to ocelot_vsc7514.c instead.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Putting 'ocelot' in the config's name twice just to say that 'it's the
ocelot driver running on the ocelot SoC' is a bit confusing. Instead,
it's just the ocelot driver. Now that we've renamed the previous symbol
that was holding the MSCC_OCELOT_SWITCH_OCELOT into *_LIB (because
that's what it is), we're free to use this name for the driver.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Hide the CONFIG_MSCC_OCELOT_SWITCH option from users. It is meant to be
only a hardware library which is selected by the drivers that use it
(ocelot, felix).

Since it is "selected" from Kconfig, all its dependencies are manually
transferred to the driver that selects it. This is because "select" in
Kconfig language is a bit of a mess, and doesn't handle dependencies of
selected options quite right.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mscc_ocelot is a slightly better name for a module than ocelot_board or
ocelot_vsc7514 is, so let's use that.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To follow the model of felix and seville where we have one
platform-specific file, rename this file to the actual SoC it serves.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Get rid of sparse "cast to restricted __be16" warnings.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sparse is rightfully complaining about the fact that:

warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
   26 |   __builtin_constant_p((l) > (h)), (l) > (h), 0)))
      |                            ^
note: in expansion of macro ‘GENMASK_INPUT_CHECK’
   39 |  (GENMASK_INPUT_CHECK(h, l) + __GENMASK(h, l))
      |   ^~~~~~~~~~~~~~~~~~~
note: in expansion of macro ‘GENMASK’
  127 |   mask = GENMASK(width, 0);
      |          ^~~~~~~

So replace the variables that go into GENMASK with plain, signed integer
types.
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds a drop frames counter to tc flower offloading.
Reporting h/w dropped frames is necessary for some actions.
Some actions like police action and the coming introduced stream gate
action would produce dropped frames which is necessary for user. Status
update shows how many filtered packets increasing and how many dropped
in those packets.

v2: Changes
 - Update commit comments suggest by Jiri Pirko.
Signed-off-by: NPo Liu <Po.Liu@nxp.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NVlad Buslov <vladbu@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>