This adds appropriate casts to avoid a warning and print the correct
values in pr_debug.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch removes the following unused exports:
- remove the following unused EXPORT_SYMBOL's:
 - pci-acpi.c: pci_osc_support_set
 - proc.c: pci_proc_detach_bus
- remove the following unused EXPORT_SYMBOL_GPL's:
  - bus.c: pci_walk_bus
  - probe.c: pci_create_bus
  - setup-res.c: pci_claim_resource
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Functions marked __devinit will be removed after kernel init.  But being
exported they are potentially called by a module much later.

So the safer choice seems to be to keep the function even in the non
CONFIG_HOTPLUG case.

This silence the follwoing section mismatch warnings:
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_device from __ksymtab_gpl between '__ksymtab_pci_bus_add_device' (at offset 0x20) and '__ksymtab_pci_walk_bus'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_create_bus from __ksymtab_gpl between '__ksymtab_pci_create_bus' (at offset 0x40) and '__ksymtab_pci_stop_bus_device'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_max_busnr from __ksymtab_gpl between '__ksymtab_pci_bus_max_busnr' (at offset 0xc0) and '__ksymtab_pci_assign_resource_fixed'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_claim_resource from __ksymtab_gpl between '__ksymtab_pci_claim_resource' (at offset 0xe0) and '__ksymtab_pcie_port_bus_type'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_add_devices from __ksymtab between '__ksymtab_pci_bus_add_devices' (at offset 0x70) and '__ksymtab_pci_bus_alloc_resource'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_scan_bus_parented from __ksymtab between '__ksymtab_pci_scan_bus_parented' (at offset 0x90) and '__ksymtab_pci_root_buses'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_assign_resources from __ksymtab between '__ksymtab_pci_bus_assign_resources' (at offset 0x4d0) and '__ksymtab_pci_bus_size_bridges'
WARNING: drivers/built-in.o - Section mismatch: reference to .init.text:pci_bus_size_bridges from __ksymtab between '__ksymtab_pci_bus_size_bridges' (at offset 0x4e0) and '__ksymtab_pci_setup_cardbus'
Signed-off-by: NSam Ravnborg <sam@ravnborg.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Since commit 368c73d4 the kernel will try
to update the non-writeable BAR registers 0..3 of PIIX4 IDE adapters if
pci_assign_unassigned_resources() is used to do full resource assignment of
the bus.  This fails because in the PIIX4 these BAR registers have
implicitly assumed values and read back as zero; it used to work because
the kernel used to just write zero to that register the read back value did
match what was written.

The fix is a new resource flag IORESOURCE_PCI_FIXED used to mark a resource
as non-movable.  This will also be useful to keep other import system
resources from being moved around - for example system consoles on PCI
busses.

[akpm@osdl.org: cleanup]
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on a patch series originally from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This is needed if we wish to change the size of the resource structures.

Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>

Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PCI: Add pci_assign_resource_fixed -- allow fixed address assignments

On some embedded systems the PCI address for hotplug devices are not only
known a priori but are required to be at a given PCI address for other
master in the system to be able to access.

An example of such a system would be an FPGA which is setup from user space
after the system has booted.  The FPGA may be access by DSPs in the system
and those DSPs expect the FPGA at a fixed PCI address.

Added pci_assign_resource_fixed() as a way to allow assignment of the PCI
devices's BARs at fixed PCI addresses.
Signed-off-by: NKumar Gala <galak@kernel.crashing.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The RPAPHP hoplug driver will not build as a module, because it calls
on pci_claim_resource(), which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>

A grep indicates that building drivers/parisc/lba_pci.c
would have trouble building as a module for the same reason.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There were three changes necessary in order to allow
sparc64 to use setup-res.c:

1) Sparc64 roots the PCI I/O and MEM address space using
   parent resources contained in the PCI controller structure.
   I'm actually surprised no other platforms do this, especially
   ones like Alpha and PPC{,64}.  These resources get linked into the
   iomem/ioport tree when PCI controllers are probed.

   So the hierarchy looks like this:

   iomem --|
	   PCI controller 1 MEM space --|
				        device 1
					device 2
					etc.
	   PCI controller 2 MEM space --|
				        ...
   ioport --|
            PCI controller 1 IO space --|
					...
            PCI controller 2 IO space --|
					...

   You get the idea.  The drivers/pci/setup-res.c code allocates
   using plain iomem_space and ioport_space as the root, so that
   wouldn't work with the above setup.

   So I added a pcibios_select_root() that is used to handle this.
   It uses the PCI controller struct's io_space and mem_space on
   sparc64, and io{port,mem}_resource on every other platform to
   keep current behavior.

2) quirk_io_region() is buggy.  It takes in raw BUS view addresses
   and tries to use them as a PCI resource.

   pci_claim_resource() expects the resource to be fully formed when
   it gets called.  The sparc64 implementation would do the translation
   but that's absolutely wrong, because if the same resource gets
   released then re-claimed we'll adjust things twice.

   So I fixed up quirk_io_region() to do the proper pcibios_bus_to_resource()
   conversion before passing it on to pci_claim_resource().

3) I was mistakedly __init'ing the function methods the PCI controller
   drivers provide on sparc64 to implement some parts of these
   routines.  This was, of course, easy to fix.

So we end up with the following, and that nasty SPARC64 makefile
ifdef in drivers/pci/Makefile is finally zapped.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Writing even a disabled value seems to mess up some matrox graphics
cards.  It may be a card-related issue, but we may also be writing
reserved low bits in the result.

This was a fall-out of switching x86 over to the generic PCI resource
allocation code, and needs more debugging.  In particular, the old x86
code defaulted to not doing any resource allocations at all for ROM
resources.

In the meantime, this has been reported to make X happier by Helge
Hafting <helgehaf@aitel.hist.no>.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Revert commit fec59a71, which is
breaking sparc64 that doesn't have a working pci_update_resource.

We'll re-do this after 2.6.13 when we'll do it all properly.

For 64-bit BAR[i] only pci_dev->resource[i] is valid, ->resource[i+1]
slot is unused and contains zeroes in all fields.

So when we update a PCI BAR, all we need is just to check that we're
going to update a _valid_ resource.

Also make sure to write high bits - use "x >> 16 >> 16" (rather than the
simpler ">> 32") to avoid warnings on 32-bit architectures where we're
not going to have any high bits.
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Some PCI devices (e.g. 3c905B, 3c556B) lose all configuration
(including BARs) when transitioning from D3hot->D0.  This leaves such
a device in an inaccessible state.  The patch below causes the BARs
to be restored when enabling such a device, so that its driver will
be able to access it.

The patch also adds pci_restore_bars as a new global symbol, and adds a
correpsonding EXPORT_SYMBOL_GPL for that.

Some firmware (e.g. Thinkpad T21) leaves devices in D3hot after a
(re)boot.  Most drivers call pci_enable_device very early, so devices
left in D3hot that lose configuration during the D3hot->D0 transition
will be inaccessible to their drivers.

Drivers could be modified to account for this, but it would
be difficult to know which drivers need modification.  This is
especially true since often many devices are covered by the same
driver.  It likely would be necessary to replicate code across dozens
of drivers.

The patch below should trigger only when transitioning from D3hot->D0
(or at boot), and only for devices that have the "no soft reset" bit
cleared in the PM control register.  I believe it is safe to include
this patch as part of the PCI infrastructure.

The cleanest implementation of pci_restore_bars was to call
pci_update_resource.  Unfortunately, that does not currently exist
for the sparc64 architecture.  The patch below includes a null
implemenation of pci_update_resource for sparc64.

Some have expressed interest in making general use of the the
pci_restore_bars function, so that has been exported to GPL licensed
modules.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!