The WEP code in the mac80211 subsystem currently uses the crypto
API to access the arc4 (RC4) cipher, which is overly complicated,
and doesn't really have an upside in this particular case, since
ciphers are always synchronous and therefore always implemented in
software. Given that we have no accelerated software implementations
either, it is much more straightforward to invoke a generic library
interface directly.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: NBalaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: NAshok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: NBalaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for Extended Key ID as defined in IEEE 802.11-2016.

 - Implement the nl80211 API for Extended Key ID
 - Extend mac80211 API to allow drivers to support Extended Key ID
 - Enable Extended Key ID by default for drivers only supporting SW
   crypto (e.g. mac80211_hwsim)
 - Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
 - Select the decryption key based on the MPDU keyid
 - Enforce existing assumptions in the code that rekeys don't change the
   cipher
Signed-off-by: NAlexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The starting of AP interface can fail due to invalid
beacon interval, which does not match the minimum gcd
requirement set by the wifi driver. In such case, the
beacon interval of that interface gets updated with
that invalid beacon interval.

The next time that interface is brought up in AP mode,
an interface combination check is performed and the
beacon interval is taken from the previously set value.

In a case where an invalid beacon interval, i.e. a beacon
interval value which does not satisfy the minimum gcd criteria
set by the driver, is set, all the subsequent trials to
bring that interface in AP mode will fail, even if the
subsequent trials have a valid beacon interval.

To avoid this, in case of a failure in bringing up an
interface in AP mode due to interface combination error,
the interface beacon interval which is stored in bss
conf, needs to be restored with the last working value
of beacon interval.

Tested on ath10k using WCN3990.

Cc: stable@vger.kernel.org
Fixes: 0c317a02 ("cfg80211: support virtual interfaces with different beacon intervals")
Signed-off-by: NRakesh Pillai <pillair@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Following call trace is observed while adding TDLS peer entry in driver
during TDLS setup.

Call Trace:
[<c1301476>] dump_stack+0x47/0x61
[<c10537d2>] __warn+0xe2/0x100
[<fa22415f>] ? sta_apply_parameters+0x49f/0x550 [mac80211]
[<c1053895>] warn_slowpath_null+0x25/0x30
[<fa22415f>] sta_apply_parameters+0x49f/0x550 [mac80211]
[<fa20ad42>] ? sta_info_alloc+0x1c2/0x450 [mac80211]
[<fa224623>] ieee80211_add_station+0xe3/0x160 [mac80211]
[<c1876fe3>] nl80211_new_station+0x273/0x420
[<c170f6d9>] genl_rcv_msg+0x219/0x3c0
[<c170f4c0>] ? genl_rcv+0x30/0x30
[<c170ee7e>] netlink_rcv_skb+0x8e/0xb0
[<c170f4ac>] genl_rcv+0x1c/0x30
[<c170e8aa>] netlink_unicast+0x13a/0x1d0
[<c170ec18>] netlink_sendmsg+0x2d8/0x390
[<c16c5acd>] sock_sendmsg+0x2d/0x40
[<c16c6369>] ___sys_sendmsg+0x1d9/0x1e0

Fixing this by allowing TDLS setup request only when we have completed
association.
Signed-off-by: NBalaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use bitrate moving average to smooth out link metric and stablize path
selection.
Signed-off-by: NJulan Hsu <julanhsu@google.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Expose path change count to destination in mpath info
Signed-off-by: NJulan Hsu <julanhsu@google.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Expose hop count to destination information in mpath info
Signed-off-by: NJulan Hsu <julanhsu@google.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds airtime accounting and scheduling to the mac80211 TXQ
scheduler. A new callback, ieee80211_sta_register_airtime(), is added
that drivers can call to report airtime usage for stations.

When airtime information is present, mac80211 will schedule TXQs
(through ieee80211_next_txq()) in a way that enforces airtime fairness
between active stations. This scheduling works the same way as the ath9k
in-driver airtime fairness scheduling. If no airtime usage is reported
by the driver, the scheduler will default to round-robin scheduling.

For drivers that don't control TXQ scheduling in software, a new API
function, ieee80211_txq_may_transmit(), is added which the driver can use
to check if the TXQ is eligible for transmission, or should be throttled to
enforce fairness. Calls to this function must also be enclosed in
ieee80211_txq_schedule_{start,end}() calls to ensure proper locking.

The API ieee80211_txq_may_transmit() also ensures that TXQ list will be
aligned aginst driver's own round-robin scheduler list. i.e it rotates
the TXQ list till it makes the requested node becomes the first entry
in TXQ list. Thus both the TXQ list and driver's list are in sync.
Co-developed-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NLouie Lu <git@louie.lu>
[added debugfs write op to reset airtime counter]
Signed-off-by: NToke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: NRajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The pointer and corresponding length is always set in pairs
in cfg80211, so no need to have this strange defensive check
that also confuses static checkers. Clean it up.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When userspace is controlling mesh routing, it may have better
knowledge about whether a mesh STA is connected to a mesh
gate than the kernel mpath table.  Add dot11MeshConnectedToMeshGate
to the mesh config so that such applications can explicitly
signal that a mesh STA is connected to a gate, which will then
be advertised in the beacon.
Signed-off-by: NBob Copeland <bobcopeland@fb.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's nothing much for mac80211 to do, so only pass through
the requests with minimal checks and tracing. The driver must
call cfg80211's results APIs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the FTM responder settings are changed simultaneously with
the CSA beacon, the buffer size allocated isn't sufficient and
we'll have a heap overrun. Fix this.

While at it, also clean up the ftm_responder assignment, doing
it only if ftm_responder is non-zero is valid as it's 0 to start
with, but not really useful to understand the code.

Fixes: bc847970 ("mac80211: support FTM responder configuration/statistics")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

New bss param ftm_responder is used to notify the driver to
enable fine timing request (FTM) responder role in AP mode.

Plumb the new cfg80211 API for FTM responder statistics through to
the driver API in mac80211.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

key->sta is only valid after ieee80211_key_link, which is called later
in this function. Because of that, the IEEE80211_KEY_FLAG_RX_MGMT is
never set when management frame protection is enabled.

Fixes: e548c49e ("mac80211: add key flag for management keys")
Cc: stable@vger.kernel.org
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In AP mode, If AP advertises HE capabilities, set to true
bss_conf::he_supported so that the Driver knows about it.
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

These checks aren't necessary, cfg80211 never passes NULL.
Some static checkers complain about the missing checks on
the next line, but really the NULL checks are unnecessary.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Make ieee80211_send_layer2_update() a common function so other drivers
can re-use it.
Signed-off-by: NDedy Lansky <dlansky@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As explained in ieee80211_delayed_tailroom_dec(), during roam,
keys of the old AP will be destroyed and new keys will be
installed. Deletion of the old key causes
crypto_tx_tailroom_needed_cnt to go from 1 to 0 and the new key
installation causes a transition from 0 to 1.

Whenever crypto_tx_tailroom_needed_cnt transitions from 0 to 1,
we invoke synchronize_net(); the reason for doing this is to avoid
a race in the TX path as explained in increment_tailroom_need_count().
This synchronize_net() operation can be slow and can affect the station
roam time. To avoid this, decrementing the crypto_tx_tailroom_needed_cnt
is delayed for a while so that upon installation of new key the
transition would be from 1 to 2 instead of 0 to 1 and thereby
improving the roam time.

This is all correct for a STA iftype, but deferring the tailroom_needed
decrement for other iftypes may be unnecessary.

For example, let's consider the case of a 4-addr client connecting to
an AP for which AP_VLAN interface is also created, let the initial
value for tailroom_needed on the AP be 1.

* 4-addr client connects to the AP (AP: tailroom_needed = 1)
* AP will clear old keys, delay decrement of tailroom_needed count
* AP_VLAN is created, it takes the tailroom count from master
  (AP_VLAN: tailroom_needed = 1, AP: tailroom_needed = 1)
* Install new key for the station, assume key is plumbed in the HW,
  there won't be any change in tailroom_needed count on AP iface
* Delayed decrement of tailroom_needed count on AP
  (AP: tailroom_needed = 0, AP_VLAN: tailroom_needed = 1)

Because of the delayed decrement on AP iface, tailroom_needed count goes
out of sync between AP(master iface) and AP_VLAN(slave iface) and
there would be unnecessary tailroom created for the packets going
through AP_VLAN iface.

Also, WARN_ONs were observed while trying to bring down the AP_VLAN
interface:
(warn_slowpath_common) (warn_slowpath_null+0x18/0x20)
(warn_slowpath_null) (ieee80211_free_keys+0x114/0x1e4)
(ieee80211_free_keys) (ieee80211_del_virtual_monitor+0x51c/0x850)
(ieee80211_del_virtual_monitor) (ieee80211_stop+0x30/0x3c)
(ieee80211_stop) (__dev_close_many+0x94/0xb8)
(__dev_close_many) (dev_close_many+0x5c/0xc8)

Restricting delayed decrement to station interface alone fixes the problem
and it makes sense to do so because delayed decrement is done to improve
roam time which is applicable only for client devices.
Signed-off-by: NManikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add support for HE in mac80211 conforming with P802.11ax_D1.4.

Johannes: Fix another bug with the buf_size comparison in agg-rx.c.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Support the new random SN and minimal probe request contents
scan flags for the case of software scan - for hardware scan
the drivers need to opt in, but may need to do only that,
depending on their implementation.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

This fixes memory leaks in the case where we just have the
station info on the stack for internal usage without sending
it to cfg80211.

Fixes: 8689c051 ("cfg80211: dynamically allocate per-tid stats for station info")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds support to mac80211 to export TXQ stats via the newly added
cfg80211 API.
Signed-off-by: NToke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If userspace requested control port frames to go over 80211, then do so.
The control packets are intercepted just prior to delivery of the packet
to the underlying network device.

Pre-authentication type frames (protocol: 0x88c7) are also forwarded
over nl80211.
Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Signed-off-by: NDenis Kenzior <denkenz@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ETSI has recently added new requirements that restrict the WMM
parameter values for 5GHz frequencies.  We need to take care of the
following scenarios in order to comply with these new requirements:

1. When using mac80211 default values;
2. When the userspace tries to configure its own values;
3. When associating to an AP which advertises WWM IE.

When associating to an AP, the client uses the values in the
advertised WMM IE.  But the AP may not comply with the new ETSI
requirements, so the client needs to check the current regulatory
rules and use those limits accordingly.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

With drivers implementing rate control in driver or firmware
rate_control_send_low() may not get called, and thus the
driver needs to know about changes in the multicast rate.

Add and use a new BSS change flag for this.
Signed-off-by: NPradeep Kumar Chitrapu <pradeepc@codeaurora.org>
[rewrite commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When powersave is disabled for the interface, we can do fast-rx anyway.
Signed-off-by: NFelix Fietkau <nbd@nbd.name>
[fixed indentation on one line]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

gcc-8 warns about some obviously incorrect code:

net/mac80211/cfg.c: In function 'cfg80211_beacon_dup':
net/mac80211/cfg.c:2896:3: error: 'memcpy' source argument is the same as destination [-Werror=restrict]

From the context, I conclude that we want to copy from beacon into
new_beacon, as we do in the rest of the function.

Cc: stable@vger.kernel.org
Fixes: 73da7d5b ("mac80211: add channel switch command and beacon callbacks")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Instead of calling ieee80211_recalc_txpower on monitor interfaces
directly, call it using the virtual monitor interface, if one exists.

In case of a single monitor interface given, reject setting TX power,
if no virtual monitor interface exists.

That being checked, don't warn in ieee80211_bss_info_change_notify,
after setting TX power on a monitor interface.

Fixes warning:
------------[ cut here ]------------
 WARNING: CPU: 0 PID: 2193 at net/mac80211/driver-ops.h:167
 ieee80211_bss_info_change_notify+0x111/0x190 Modules linked in: uvcvideo
 videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_core
rndis_host cdc_ether usbnet mii tp_smapi(O) thinkpad_ec(O) ohci_hcd vboxpci(O)
 vboxnetadp(O) vboxnetflt(O) v boxdrv(O) x86_pkg_temp_thermal kvm_intel kvm
 irqbypass iwldvm iwlwifi ehci_pci ehci_hcd tpm_tis tpm_tis_core tpm CPU: 0
 PID: 2193 Comm: iw Tainted: G           O    4.12.12-gentoo #2 task:
 ffff880186fd5cc0 task.stack: ffffc90001b54000 RIP:
 0010:ieee80211_bss_info_change_notify+0x111/0x190 RSP: 0018:ffffc90001b57a10
 EFLAGS: 00010246 RAX: 0000000000000006 RBX: ffff8801052ce840 RCX:
 0000000000000064 RDX: 00000000fffffffc RSI: 0000000000040000 RDI:
 ffff8801052ce840 RBP: ffffc90001b57a38 R08: 0000000000000062 R09:
 0000000000000000 R10: ffff8802144b5000 R11: ffff880049dc4614 R12:
 0000000000040000 R13: 0000000000000064 R14: ffff8802105f0760 R15:
 ffffc90001b57b48 FS:  00007f92644b4580(0000) GS:ffff88021e200000(0000)
 knlGS:0000000000000000 CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
 CR2: 00007f9263c109f0 CR3: 00000001df850000 CR4: 00000000000406f0
 Call Trace:
  ieee80211_recalc_txpower+0x33/0x40
  ieee80211_set_tx_power+0x40/0x180
  nl80211_set_wiphy+0x32e/0x950
Reported-by: NPeter Große <pegro@friiks.de>
Signed-off-by: NPeter Große <pegro@friiks.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.

Notice that in some cases I replaced "fall through on else" and
"otherwise fall through" comments with just a "fall through" comment,
which is what GCC is expecting to find.
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Ben reported that when the user rate mask is rejected for not
matching any basic rate, the driver had already been configured.
This is clearly an oversight in my original change, fix this by
doing the validation before calling the driver.
Reported-by: NBen Greear <greearb@candelatech.com>
Fixes: e8e4f528 ("mac80211: reject/clear user rate mask if not usable")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It seems like a historic accident that these return unsigned char *,
and in many places that means casts are required, more often than not.

Make these functions (skb_put, __skb_put and pskb_put) return void *
and remove all the casts across the tree, adding a (u8 *) cast only
where the unsigned char pointer was used directly, all done with the
following spatch:

    @@
    expression SKB, LEN;
    typedef u8;
    identifier fn = { skb_put, __skb_put };
    @@
    - *(fn(SKB, LEN))
    + *(u8 *)fn(SKB, LEN)

    @@
    expression E, SKB, LEN;
    identifier fn = { skb_put, __skb_put };
    type T;
    @@
    - E = ((T *)(fn(SKB, LEN)))
    + E = fn(SKB, LEN)

which actually doesn't cover pskb_put since there are only three
users overall.

A handful of stragglers were converted manually, notably a macro in
drivers/isdn/i4l/isdn_bsdcomp.c and, oddly enough, one of the many
instances in net/bluetooth/hci_sock.c. In the former file, I also
had to fix one whitespace problem spatch introduced.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mac80211 allows to modify the SMPS state of an AP both,
when it is started, and after it has been started. Such a
change will trigger an action frame to all the peers that
are currently connected, and will be remembered so that
new peers will get notified as soon as they connect (since
the SMPS setting in the beacon may not be the right one).

This means that we need to remember the SMPS state
currently requested as well as the SMPS state that was
configured initially (and advertised in the beacon).
The former is bss->req_smps and the latter is
sdata->smps_mode.

Initially, the AP interface could only be started with
SMPS_OFF, which means that sdata->smps_mode was SMPS_OFF
always. Later, a nl80211 API was added to be able to start
an AP with a different AP mode. That code forgot to update
bss->req_smps and because of that, if the AP interface was
started with SMPS_DYNAMIC, we had:
   sdata->smps_mode = SMPS_DYNAMIC
   bss->req_smps = SMPS_OFF

That configuration made mac80211 think it needs to fire off
an action frame to any new station connecting to the AP in
order to let it know that the actual SMPS configuration is
SMPS_OFF.

Fix that by properly setting bss->req_smps in
ieee80211_start_ap.

Fixes: f6993174 ("mac80211: set smps_mode according to ap params")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If userspace has flagged support for DFS earlier, then we can follow CSA
to DFS channels. So instead of rejecting the switch, allow it to happen
if the flag has been set during mesh setup.
Signed-off-by: NBenjamin Berg <benjamin@sipsolutions.net>
Signed-off-by: NSimon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even
if the channel context configuration is NULL. This crashes for chipsets
which support 5 Ghz alone when it tries to access members of 'sband'.
Channel context configuration can be NULL in multivif case and when
channel switch is in progress (or) when it fails. Fix this by replacing
the API 'ieee80211_get_sdata_band' with  'ieee80211_get_sband' which
returns a NULL pointer for sband when the channel configuration is NULL.

An example scenario is as below:

In multivif mode (AP + STA) with drivers like ath10k, when we do a
channel switch in the AP vif (which has a number of clients connected)
and a STA vif which is connected to some other AP, when the channel
switch in AP vif fails, while the STA vifs tries to connect to the
other AP, there is a window where the channel context is NULL/invalid
and this results in a crash  while the clients connected to the AP vif
tries to reconnect and this race is very similar to the one investigated
by Michal in https://patchwork.kernel.org/patch/3788161/ and this does
happens with hardware that supports 5Ghz alone after long hours of
testing with continuous channel switch on the AP vif

ieee80211 phy0: channel context reservation cannot be finalized because
some interfaces aren't switching
wlan0: failed to finalize CSA, disconnecting
wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice
	(Reason: 3=DEAUTH_LEAVING)

	WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211]
	[<bf77272c>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211]))
	[<bf73cc50>] (nl80211_new_station [cfg80211])

	Unable to handle kernel NULL pointer dereference at virtual
	address 00000014
	pgd = d5f4c000
	Internal error: Oops: 17 [#1] PREEMPT SMP ARM
	PC is at sta_info_alloc+0x380/0x3fc [mac80211]
	LR is at sta_info_alloc+0x37c/0x3fc [mac80211]
	[<bf772738>] (sta_info_alloc [mac80211])
	[<bf78776c>] (ieee80211_add_station [mac80211])
	[<bf73cc50>] (nl80211_new_station [cfg80211]))

Cc: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: NMohammed Shafi Shajakhan <mohammed@qti.qualcomm.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

At least on iwlwifi, sometimes lockdep complains that we can
lock
 chanctx_mtx -> mvm.mutex -> iflist_mtx
 (due to iterate_interfaces)
and
 iflist_mtx -> chanctx_mtx

Remove the latter dependency in mac80211 by using the RTNL
that we already hold in one case, and can relatively easily
achieve in the other case.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

For multiple scheduled scan support the driver needs to know which
scheduled scan request is being stopped. Pass the request id in the
.sched_scan_stop() callback.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Refactor the code to have common code for changing monitor
options when adding and changing virtual interfaces. This
will make it easier to add BPF filters to both paths. Note
that this code carefully checks the error conditions first
and only then applies the changes, to guarantee atomicity.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>