This firmware will be the first firmware to support
3168. It hasn't been released yet.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Add some new PCI IDs for the 8260 series which were missing.
The following sub-system IDs were added:
0x0130, 0x1130, 0x0132, 0x1132, 0x1150, 0x8110, 0x9110, 0x8130,
0x9130, 0x8132, 0x9132, 0x8150, 0x9150, 0x0044, 0x0930

CC: <stable@vger.kernel.org> [4.1+]
Signed-off-by: NOren Givon <oren.givon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix a place where checkpatch complains that braces should be used
on all arms of this statement.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixes those places where checkpatch complains that comparisons
should place the constant on the right side of the test.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The value passed through switchdev attr set is not in jiffies, but in
clock_t, so fix the convert.
Reported-by: NSagi Rotem <sagir@mellanox.com>
Fixes: 56ade8fe ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix copy-paste errors.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original description was for LAG, so fix it.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add or remove a bridged port from the flooding domain of unknown unicast
packets according to user configuration.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling a range of VLANs on a bridged port we can configure
flooding for these VLANs by one register access instead of calling the
same register for each VLAN. This is accomplished by using the 'range'
field of the Switch Flooding Table Register (SFTR).
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is a flag anyway, so move it to existing u8 flag and don't waste mem.
Fix the flags to be in single u8 on the way.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add RGMII TX/RX delay configuration support. RGMII standard requires 2ns
delay to help the RGMII bridge receiver to sample data correctly. If the
default value does not provide proper centering of the data sample, the
TX/RX delay parameters can be used to adjust accordingly.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reviewed-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other callers of udp_tunnel6_xmit_skb just pass 0 for the prio
argument.  Jesse Gross <jesse@nicira.com> suggested that prio is really
the same as IPv4's tos and should be handled the same, so this is my
interpretation of that suggestion.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reported-by: NJesse Gross <jesse@nicira.com>
Reviewed-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NOTE: Link-local IPv6 addresses for remote endpoints are not supported,
since the driver currently has no capacity for binding a geneve
interface to a specific link.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Reviewed-by: NJesse Gross <jesse@nicira.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This supports a way to get target stats through normal
ethtool stats API.

For instance:
# ethtool -S wlan1
NIC statistics:
     tx_pkts_nic: 353
     tx_bytes_nic: 25142
     rx_pkts_nic: 6
     rx_bytes_nic: 996
     d_tx_ucast_pkts: 89
     d_tx_bcast_pkts: 264
     d_tx_ucast_bytes: 3020
     d_tx_bcast_bytes: 22122
...
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This will allow us to call it from elsewhere when implementing
ethtool stats.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Improper use of strlcpy caused garbage to be appended to the
firmware version string.  Fix this by paying attention to the
ie_lenth.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It can take a user a while to understand why their
NIC that advertises 802.11n support cannot actually
do 802.11n.  Print out a warning in the logs to save
the next poor person to use this NIC some trouble.
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This lets 'iw phy phy0 info' report antennas for
the radio device:

...
	Available Antennas: TX 0x2 RX 0x2
	Configured Antennas: TX 0x2 RX 0x2
...
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When configuring Tx vring for new connection,
WMI call to the firmware may fail. In this case, need to
clean up properly. In particular, need to call
cfg80211_del_sta() in case of AP like interface.

Perform full "disconnect" procedure for proper clean up
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Adjust driver behavior during FW boot. Proper sequence of
events after reset and FW download, is as following:

- FW prepares mailbox structure and reports IRQ "FW_READY"
- driver caches mailbox registers, marks mailbox readiness
- FW sends WMI_FW_READY event, ignore it
- FW sends WMI_READY event with some data
- driver stores relevant data marks FW is operational
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When Tx ring full is encountered with TSO,
printout of "DMA error" was wrongly printed.

In addition, in case of Tx ring full return
proper error code so that NETDEV_TX_BUSY is
returned to network stack in order not to
drop the packets and retry transmission of the
packets when ring is emptied.
Signed-off-by: NHamad Kadmany <qca_hkadmany@qca.qualcomm.com>
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Some events are ignored for purpose; such events should not
be treated as "unhandled events". Replace info message
saying "unhandled" with debug one saying "ignore", to reduce
dmesg pollution
Signed-off-by: NVladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add the hardware name, revision and update the pci_id table.

Currently there're two HW ref. designs available I'm aware of,
with 1.0.2 and 1.1 chip revisions. I've access and been using
the first one so far and this patch cover only it.

QCA9377 inherits most of the stuff (e.g. fw interfaces)
from QCA61x4 design, so the integration was pretty straightforward.
Signed-off-by: NBartosz Markowski <bartosz.markowski@tieto.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To reflect configured antenna settings in HT/VHT MCS map,
reload the HT/VHT capabilities upon antenna change.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Move HT and VHT capabiltity setup static functions to avoid
forward declaration.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

HT/VHT MCS rateset should be filled only for configured chainmask
rather that max supported chainmask. Fix that by checking configured
chainmask while filling HT/VHT MCS rate map.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Removing supported chainmask fields as it can be always derived
from num_rf_chains.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For the messages from host to target, shadow copy of CE descriptors
are maintained in source ring. Before writing actual CE descriptor,
first shadow copy is filled and then it is copied to CE address space.
To optimize in download path and to reduce d-cache pressure, removing
shadow copy of CE descriptors. This will also reduce driver memory
consumption by 33KB during on device probing.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The physical address necessary to unmap DMA ('bufferp') is stored
in ath10k_skb_cb as 'paddr'. ath10k doesn't rely on the meta/transfer_id
when handling send completion (htc ep id is stored in sk_buff control
buffer). So the unused output arguments {bufferp, nbytesp and transfer_idp}
are removed from CE send completion. This change is needed before removing
the shadow copy of copy engine (CE) descriptors in follow up patch.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

CE diag window access is serialized (it has to be by design) so
there's no way to get a different send completion. so there's no
need for post completion validation.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently to avoid uncached memory access while filling up copy engine
descriptors, shadow descriptors are used. This can be optimized further
by removing shadow descriptors. To achieve that first shadow ring
dependency in ce_send is removed by creating local copy of the
descriptor on stack and make a one-shot copy into the "uncached"
descriptor.
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch adds support for getting firmware debug stats in 10.4 fw.
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NTamizh chelvam <c_traja@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add WMI-TLV and FW API support in ath10k testmode.
Ath10k can get right wmi command format from UTF image
to communicate UTF firmware.
Signed-off-by: NAlan Liu <alanliu@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

European Union has made it mandatory that all devices working in 2.4 GHz
has to adhere to the ETSI specification (ETSI EN 300 328 V1.9.1)
beginnig this year. The standard basically speaks about interferences
in 2.4Ghz band.
For example, when 802.11 device detects interference, TX must be stopped
as long as interference is present.

Adaptive CCA is a feature, when enabled the device learns from the
environment and configures CCA levels adaptively. This will improve
detecting interferences and the device can stop trasmissions till the
interference is present eventually leading to good performances in
varying interference conditions.

The patch includes code for enabling adaptive CCA for 10.2.4 firmware on
QCA988X.
Signed-off-by: NMaharaja <c_mkenna@qti.qualcomm.com>
Signed-off-by: NManikanta Pubbisetty <c_mpubbi@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows saving a little of space when not using ssb on Broadcom SoC.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This cleans main.c a bit and will allow us to compile SoC related code
conditionally in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ssb bus can be found on various "host" devices like PCI/PCMCIA/SDIO.
Every ssb bus contains cores AKA devices.
The main idea is to have ssb driver scan/initialize bus and register
ready-to-use cores. This way ssb drivers can operate on a single core
mostly ignoring underlaying details.

For some reason PCMCIA support was split between ssb and b43. We got
PCMCIA host device probing in b43, then bus scanning in ssb and then
wireless core probing back in b43. The truth is it's very unlikely we
will ever see PCMCIA ssb device with no 802.11 core but I still don't
see any advantage of the current architecture.

With proposed change we get the same functionality with a simpler
architecture, less Kconfig symbols, one killed EXPORT and hopefully
cleaner b43. Since b43 supports both: ssb & bcma I prefer to keep ssb
specific code in ssb driver.

This mostly moves code from b43's pcmcia.c to bridge_pcmcia_80211.c. We
already use similar solution with b43_pci_bridge.c. I didn't use "b43"
in name of this new file as in theory any driver can operate on wireless
core.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>