Get the reset control properties for the QSPI controller and bring them
out of reset. Most will have just one reset bit, but there is an additional
OCP reset bit that is used ECC. The OCP reset bit will also need to get
de-asserted as well. [1]

The reason this patch is needed is in the case where a bootloader leaves
the QSPI controller in a reset state, or a state where init cannot occur
successfully, the patch will put the QSPI controller into a clean state.

[1] https://www.intel.com/content/www/us/en/programmable/hps/arria-10/hps.html#reg_soc_top/sfo1429890575955.htmlSuggested-by: NTien-Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>
[tudor.ambarus@microchip.com: declare rstc and rstc_ocp on the same line]
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

mtd: spi-nor: fix nor->addr_width when its value configured from SFDP does not match the actual width

IS25LP256 gets BFPT_DWORD1_ADDRESS_BYTES_3_ONLY from BFPT table for
address width. But in actual fact the flash can support 4-byte address.
Use a post bfpt fixup hook to overwrite the address width advertised by
the BFPT.
Signed-off-by: NLiu Xiang <liu.xiang6@zte.com.cn>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

SPI memory devices from different manufacturers have widely
different configurations for Status, Control and Configuration
registers. JEDEC 216C defines a new map for these common register
bits and their functions, and describes how the individual bits may
be accessed for a specific device. For the JEDEC 216B compliant
flashes, we can partially deduce Status and Configuration registers
functions by inspecting the 16th DWORD of BFPT. Older flashes that
don't declare the SFDP tables (SPANSION FL512SAIFG1 311QQ063 A ©11
SPANSION) let the software decide how to interact with these registers.

The commit dcb4b22e ("spi-nor: s25fl512s supports region locking")
uncovered a probe error for s25fl512s, when the Quad Enable bit CR[1]
was set to one in the bootloader. When this bit is one, only the Write
Status (01h) command with two data byts may be used, the 01h command with
one data byte is not recognized and hence the error when trying to clear
the block protection bits.

Fix the above by using the Write Status (01h) command with two data bytes
when the Quad Enable bit is one.

Backward compatibility should be fine. The newly introduced
spi_nor_spansion_clear_sr_bp() is tightly coupled with the
spansion_quad_enable() function. Both assume that the Write Register
with 16 bits, together with the Read Configuration Register (35h)
instructions are supported.

Fixes: dcb4b22e ("spi-nor: s25fl512s supports region locking")
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: NJonas Bonn <jonas@norrbonn.se>
Tested-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NVignesh Raghavendra <vigneshr@ti.com>
Tested-by: NVignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

This gets rid of the license boilerplate duplicated in each file.

No functional changes intended.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Intel Elkhart Lake has the same SPI serial flash controller as Ice Lake.
Add Elkhart Lake PCI ID to the driver list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Testing done on Mikrotik Routerboard RB450Gx4 board under
4.14.119 and 4.19.43 kernels. The test board does not support
Dual or Quad modes.

Datasheet at:
https://www.winbond.com/resource-files/w25q16jv%20spi%20revg%2003222018%20plus.pdfSigned-off-by: NRobert Marko <robimarko@gmail.com>
[tudor.ambarus@microchip.com: w25q16jv-im/jm and w25q16jv-iq/jq
have different jedec ids, fix flash name.]
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NEnrico Weigelt <info@metux.net>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 503 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAlexios Zavras <alexios.zavras@intel.com>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NEnrico Weigelt <info@metux.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190602204653.811534538@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case of SPI error during the reading of the nor Id,
the probe fails without any error message related to
the JEDEC Id reading procedure.
Signed-off-by: NFlavio Suligoi <f.suligoi@asem.it>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Add an entry for Micron MT25QL02 which is a 3V variant of already
supported MT25QU02.

Testing was done on a ZII VF610 Dev Board (rev. B).
Signed-off-by: NCory Tusar <cory.tusar@pid1solutions.com>
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tudor Ambarus <tudor.ambarus@microchip.com>
Cc: linux-mtd@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
[tudor.ambarus@microchip.com: order entry alphabetically, wrap to
80 chars limit]
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

There's a new driver using the SPI memory interface of the
SPI framework at spi/spi-stm32-qspi.c, which can be used
together with m25p80.c to replace the functionality of
this SPI NOR driver.

The "new" driver uses the same dt properties and not affects
the legacy compatibility.
Signed-off-by: NLudovic Barre <ludovic.barre@st.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms and conditions of the gnu general public license
  version 2 as published by the free software foundation this program
  is distributed in the hope it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details you should have received a copy of the gnu general
  public license along with this program if not see http www gnu org
  licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NSteve Winslow <swinslow@gmail.com>
Reviewed-by: NRichard Fontana <rfontana@redhat.com>
Reviewed-by: NAlexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license version 2 as
  published by the free software foundation this program is
  distributed in the hope that it will be useful but without any
  warranty without even the implied warranty of merchantability or
  fitness for a particular purpose see the gnu general public license
  for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-only

has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NRichard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 1 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Based on 2 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details you
  should have received a copy of the gnu general public license along
  with this program if not see http www gnu org licenses

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details [based]
  [from] [clk] [highbank] [c] you should have received a copy of the
  gnu general public license along with this program if not see http
  www gnu org licenses

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: NJilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: NSteve Winslow <swinslow@gmail.com>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add SPDX license identifiers to all Make/Kconfig files which:

 - Have no license information of any form

These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:

  GPL-2.0-only
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Intel Comet Lake has the same SPI serial flash controller as Ice Lake.
Add Comet Lake PCI ID to the driver list of supported devices.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>

Both the BP[0-2] bits and the TBPROT bit are supported on this chip.
Tested and verified on a Cypress s25fl512s.
Signed-off-by: NJonas Bonn <jonas@norrbonn.se>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

It was observed that reads crossing 4K address boundary are failing.

This limitation is mentioned in Intel documents:

Intel(R) 9 Series Chipset Family Platform Controller Hub (PCH) Datasheet:

"5.26.3 Flash Access
Program Register Access:
* Program Register Accesses are not allowed to cross a 4 KB boundary..."

Enhanced Serial Peripheral Interface (eSPI)
Interface Base Specification (for Client and Server Platforms):

"5.1.4 Address
For other memory transactions, the address may start or end at any byte
boundary. However, the address and payload length combination must not
cross the naturally aligned address boundary of the corresponding Maximum
Payload Size. It must not cross a 4 KB address boundary."

Avoid this by splitting an operation crossing the boundary into two
operations.

Fixes: 8afda8b2 ("spi-nor: Add support for Intel SPI serial flash controller")
Cc: stable@vger.kernel.org
Reported-by: NRomain Porte <romain.porte@nokia.com>
Tested-by: NPascal Fabreges <pascal.fabreges@nokia.com>
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

Erase types are sorted *smallest* type first, refer to
spi_nor_sort_erase_mask().
Signed-off-by: NAlexander Sverdlin <alexander.sverdlin@nokia.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

If identification of an SPI NOR FLASH fails, the JEDEC ID is printed,
which is stored in the first 3 bytes of the ID read from the FLASH.
However, the extended JEDEC ID, which is stored in the remaining bytes,
also matters, as it is used for identification of some FLASH types.

Print all (currently 6) ID bytes read to ease failure analysis and
debugging.
Suggested-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NMiquel Raynal <miquel.raynal@bootlin.com>

There is a spelling mistake in a dev_error message. Fix it.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

The Eon EN25QH64 is a 64 Mbit SPI NOR flash memory chip found
on recent wireless routers. Its 32, 128 and 256 Mbit siblings
are already supported.

Tested on a COMFAST CF-E120A v3 router board.
Signed-off-by: NRoger Pueyo Centelles <roger.pueyo@guifi.net>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

This adds support for the Macronix MX25V8035F, a 8Mb SPI NOR chip.
It is used on i.MX6UL/ULL SoMs by Kontron Electronics GmbH (N631x).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

This adds support for the EON EN25Q80A, a 8Mb SPI NOR chip.
It is used on i.MX6 boards by Kontron Electronics GmbH
(N60xx, N61xx).
It was only tested with a single data line connected, by writing and
reading random data with dd.
Signed-off-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

Cadence OSPI controller IP supports Octal IO (x8 IO lines),
It also has an integrated PHY. IP register layout is very
similar to existing QSPI IP except for additional bits to support Octal
and Octal DDR mode. Therefore, extend current driver to support Octal
mode. Only Octal SDR read (1-1-8)mode is supported for now.

Tested with mt35xu512aba Octal flash on TI's AM654 EVM.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

Due to two different versions (S25FL128SAGBHI200 and S25FL128SAGBHI210) of
the s25fl128s qspi memory, the single "s25fl128s" device entry must be
split into two to match the correct JEDEC ID's for each version. Solves
paging related issues of S25FL128SAGBHI210 chips.
Signed-off-by: NAhmet Celenk <ahmet.celenk@procenne.com>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

cadence-quadspi controller allows upto eight bytes of data to
be written in software Triggered Instruction generator (STIG) mode
of operation. Lower 4 bytes are written through writedatalower and
upper 4 bytes by writedataupper register.

This patch allows all the 8 bytes to be written.
Signed-off-by: NPurna Chandra Mandal <purna.chandra.mandal@intel.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

The mx25u3235f is found on the ZyXEL NBG6817 router, therefore
add driver support for it so that we can upstream board support.

Minimal tested with u-boot tools fw_printenv/fw_setenv on GlobalScale
ESPRESSObin v5 board.
Signed-off-by: NAndré Valentin <avalentin@marcant.net>
[miyatsu@qq.com: Remove unnecessary white space.]
Signed-off-by: NDing Tao <miyatsu@qq.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@collabora.com>

Spansion S25FL512S ID is erroneously using 5-byte JEDEC ID, while the chip
family ID is stored in the 6th byte. Due to using only 5-byte ID, it's also
covering S25FS512S and now that we have added 6-byte ID for that chip, we
can convert S25FL512S to using a proper 6-byte ID as well...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

Spansion S25FS512S flash is currently misdetected as S25FL512S since the
latter uses 5-byte JEDEC ID, while the 6th ID byte (family ID) is different
on those chips. Add the 6-byte S25FS512S ID before S25FL512S ID in order
not to break the existing S25FS512S users.
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

Add octal read flag for flash mt35xu512aba.
This flash, mt35xu512aba, is only complaint to SFDP JESD216B and does
not seem to support newer JESD216C standard that provides auto
detection of Octal mode capabilities and opcodes. Therefore, this
capability is manually added using new SPI_NOR_OCTAL_READ flag.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NYogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

- Add opcodes for octal I/O commands
  * Read  : 1-1-8 and 1-8-8 protocol
  * Write : 1-1-8 and 1-8-8 protocol
  * opcodes for 4-byte address mode command

- Entry of macros in _convert_3to4_xxx function

- Add flag SPI_NOR_OCTAL_READ specifying flash support octal read
  commands. This flag is required for flashes which didn't provides
  support for auto detection of Octal mode capabilities i.e. not
  seems to support newer JESD216C standard.
Signed-off-by: NVignesh R <vigneshr@ti.com>
Signed-off-by: NYogesh Narayan Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

The quadspi is a generic communication interface which could be shared
with other MediaTek SoCs. Hence rename it to a common one.
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

SNOR_HWCAPS_READ should be supported by this controller, so add this
flag to spi_nor_hwcaps mask.
Signed-off-by: NGuochun Mao <guochun.mao@mediatek.com>
Signed-off-by: NRyder Lee <ryder.lee@mediatek.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <bbrezillon@kernel.org>

There's a new driver using the SPI memory interface of the SPI framework
at spi/spi-fsl-qspi.c, which can be used together with m25p80.c to
replace the functionality of this SPI NOR driver.

The new driver is already in use and this code is not compiled anymore,
so let's remove it.
Signed-off-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: NHan Xu <han.xu@nxp.com>
Tested-by: NHan Xu <han.xu@nxp.com>
Acked-by: NBoris Brezillon <bbrezillon@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).

The controller does not support generic SPI messages.

This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: NFrieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: NHan Xu <han.xu@nxp.com>
Reviewed-by: NYogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: NYogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: NHan Xu <han.xu@nxp.com>
Reviewed-by: NBoris Brezillon <bbrezillon@kernel.org>
Signed-off-by: NMark Brown <broonie@kernel.org>

The is25lp016d is found on the iwg23s from iWave, therefore
add driver support for it so that we can upstream board support.
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@bootlin.com>

Add support for SFDP (JESD216B) 4-byte Address Instruction Table. This
table is optional but when available, we parse it to get the 4-byte
address op codes supported by the memory.
Using these op codes is stateless as opposed to entering the 4-byte
address mode or setting the Base Address Register (BAR).

Flashes that have the 4BAIT table declared can now support
SPINOR_OP_PP_1_1_4_4B and SPINOR_OP_PP_1_4_4_4B opcodes.

Tested on MX25L25673G.
Signed-off-by: NCyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com:
- rework erase and page program logic,
- pass DMA-able buffer to spi_nor_read_sfdp(),
- introduce SPI_NOR_HAS_4BAIT
- various minor updates.]
Signed-off-by: NTudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: NBoris Brezillon <boris.brezillon@bootlin.com>