This patch adds the fnic devcmd2 command structre and the command result
structure definitions.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Impose an upper limit on the max number of CQ entries (corresponding to the
copy wq) processed in an interrupt.  Use module parameter to set the limit.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Do RQ enable before posting descriptor. This is needed for later hw
revisions.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Doing vnic_device_enable before this could cause interrupts to happen
before they are setup.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The change is to print warning when scsi done is called for an IO that has
not yet been issued to the fw. Also adding sc and tag to debug print when
IO is cleaned up.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This change is to add fnic stats for the max number of CQs (corresponding
to copy WQ) processed in a given interrupt, max time taken by the ISR.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds the current fnic port speed stat to fnic debug stats.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Need to use fnic_lock as well as host lock in that order to set state
flags.

[mkp: typos]
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

rq->ctrl not enabled when this is called is bad but not fatal and can
continue.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch changes the default lun queuedepth for fnic to 256.
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch is to add fnic 20G port speed display in sysfs.

[mkp: typo]
Signed-off-by: NSatish Kharat <satishkh@cisco.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

From scsi_init_command(), a function called by scsi_mq_prep_fn():

	/* zero out the cmd, except for the embedded scsi_request */
	memset((char *)cmd + sizeof(cmd->req), 0,
		sizeof(*cmd) - sizeof(cmd->req) + dev->host->hostt->cmd_size);

In other words, scsi_mq_prep_fn() clears scsi_cmnd.flags. Hence move the
clear_bit() call into the else branch, the only branch in which this code
is necessary.

See also commit f1342709 ("scsi: Do not rely on blk-mq for double
completions").

Cc: Keith Busch <keith.busch@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NKeith Busch <keith.busch@intel.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch makes the source code more uniform and does not change any
functionality.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rework sd_setup_read_write_cmnd() so it becomes more readable. Put all the
sanity checking at the head of the function and sanitize the logged error
messages. Move the legacy SCSI logging calls to the end of the functions
and reduce conditional nesting.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Create a helper function for each of the 6, 10, 16 and 32-byte READ/WRITE
variants and use those when setting up reads and writes.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 and made
  function names shorter. ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Avoid open coding the checks for the supported logical block sizes and use
a mask to check for misaligned I/O. Use our helper functions to scale lba
and block count.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We have had several bugs due mixing sector and logical block size
terminology. In the block layer, a sector is a 512-byte unit regardless of
the logical block size of the underlying device. But the term "sector" is
still widely used in sd.c when referring to logical block sized units.

We previously introduced helper functions such as sectors_to_logical() and
logical_to_sectors() to make the distinction clear. Use these to make the
code in sd.c consistent wrt. logical blocks and block layer sectors.

Use "lba" to describe a logical block address and "nr_blocks" when counting
logical blocks. SBC uses "TRANSFER LENGTH" to describe the latter but this
term was avoided to prevent confusion with the very similar DMA transfer
size (->transfersize) which is counted in bytes.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: ported this patch from kernel v4.11 to kernel v5.0 ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch does not change any functionality.
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
[ bvanassche: extracted this patch from a larger patch ]
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

CONFIG_SCSI_UFS_QCOM selects CONFIG_PHY_QCOM_UFS, assuming that this was
the only possible PHY driver Qualcomm's UFS controller would use. But in
SDM845, the UFS driver is bundled into phy-qcom-qmp, and phy-qcom-ufs is
unused.

Remove the select, since for SDM845 it adds useless drivers to the build.
Signed-off-by: NEvan Green <evgreen@chromium.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The tmscsim.txt doc file was removed in c121107d.

Fixes: c121107d ("scsi: documentation: Obsolete documentation references")
Signed-off-by: NOtto Sabart <ottosabart@seberm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

   +----------+             +----------+
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SAS  disk
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SAS  disk
   |initiator |             |          |
   | device   |--- 3.0 G ---| Expander |--- 6.0 G --- SAS  disk
   |          |             |          |
   |          |--- 3.0 G ---|          |--- 6.0 G --- SATA disk  -->failed to connect
   |          |             |          |
   |          |             |          |--- 6.0 G --- SATA disk  -->failed to connect
   |          |             |          |
   +----------+             +----------+

According to Serial Attached SCSI - 1.1 (SAS-1.1):
If an expander PHY attached to a SATA PHY is using a physical link rate
greater than the maximum connection rate supported by the pathway from an
STP initiator port, a management application client should use the SMP PHY
CONTROL function (see 10.4.3.10) to set the PROGRAMMED MAXIMUM PHYSICAL
LINK RATE field of the expander PHY to the maximum connection rate
supported by the pathway from that STP initiator port.

Currently libsas does not support checking if this condition occurs, nor
rectifying when it does.

Such a condition is not at all common, however it has been seen on some
pre-silicon environments where the initiator PHY only supports a 1.5 Gbit
maximum linkrate, mated with 12G expander PHYs and 3/6G SATA phy.

This patch adds support for checking and rectifying this condition during
initial device discovery only.

We do support checking min pathway connection rate during revalidation phase,
when new devices can be detected in the topology. However we do not
support in the case of the the user reprogramming PHY linkrates, such that
min pathway condition is not met/maintained.

A note on root port PHY rates:
The libsas root port PHY rates calculation is broken. Libsas sets the
rates (min, max, and current linkrate) of a root port to the same linkrate
of the first PHY member of that same port. In doing so, it assumes that
all other PHYs which subsequently join the port to have the same
negotiated linkrate, when they could actually be different.

In practice this doesn't happen, as initiator and expander PHYs are
normally initialised with consistent min/max linkrates.

This has not caused an issue so far, so leave alone for now.
Tested-by: NJian Luo <luojian5@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently the SMP PHY control execution result is checked, however the
function result for the command is not.

As such, we may be missing all potential errors, like SMP FUNCTION FAILED,
INVALID REQUEST FRAME LENGTH, etc., meaning the PHY control request has
failed.

In some scenarios we need to ensure the function result is accepted, so add
a check for this.
Tested-by: NJian Luo <luojian5@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently much indentation in this file is done with whitespaces instead of
tabs, which can make reading difficult, so fix this up.

Some other little minor tidy-up is done, but this file still has many other
checkpatch warnings (generally linelength > 80 or function arguments have
no identifier names).

All libsas code can be audited for checkpatch issues later.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When SGE buffer containing DIF information crosses 4G boundary, it results
in DMA error. This patch fixes this issue by calculating SGE buffer size
and if it crosses 4G boundary, driver will split it into multiple SGE
buffers to avoid DMA error.
Signed-off-by: NGiridhar Malavali <gmalavali@marvell.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allow user to selectively enable/disable DIF/DIX protection
capabilities mask.
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NHimanshu Madhani <hmadhani@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in some cases, I replaced "FALLTHROUGH" with a "fall through"
annotation and then placed it at the bottom of the corresponding switch
case, which is what GCC is expecting to find.

Addresses-Coverity-ID: 114961 ("Missing break in switch")
Addresses-Coverity-ID: 114962 ("Missing break in switch")
Addresses-Coverity-ID: 114963 ("Missing break in switch")
Addresses-Coverity-ID: 114964 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in this particular case, I replaced "!!! fall through !!!"
comment with "fall through" annotations, which is what GCC is expecting to
find.

Addresses-Coverity-ID: 146155 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that I replaced "!! fall through !!" and "!!! fall through !!!"
comments with "fall through" annotations, which is what GCC is expecting to
find.

Addresses-Coverity-ID: 744899 ("Missing break in switch")
Addresses-Coverity-ID: 744900 ("Missing break in switch")
Addresses-Coverity-ID: 744901 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in this particular case, I replaced "!!! fall through !!!"
with a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NSudarsana Kalluru <Sudarsana.Kalluru@qlogic.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NBradley Grove <bgrove@atto.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Addresses-Coverity-ID: 114994 ("Missing break in switch")
Addresses-Coverity-ID: 114995 ("Missing break in switch")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NKai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases where
we are expecting to fall through.

Notice that, in this particular case, I replaced "allow fall-through" with
a "fall through" annotation, which is what GCC is expecting to find.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: NNilesh Javali <njavali@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The return statement is indented incorrectly, fix this by removing a single
tab.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NManish Rangankar <mrangankar@marvell.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently the protection lookup tables in sd_prot_flag_mask() and
sd_prot_op() are declared as non-static. As such, they will be rebuilt for
each respective function call.

Optimise by making them static.

This saves ~100B object code for sd.c:

Before:
   text	   data	    bss	    dec	    hex	filename
  25403	   1024	     16	  26443	   674b	drivers/scsi/sd.o

After:
  text	   data	    bss	    dec	    hex	filename
  25299	   1024	     16	  26339	   66e3	drivers/scsi/sd.o

In addition, since those same functions are declared in sd.h, but each are
only referenced in sd.c, relocate them to that same c file.

The inline specifier is dropped also, since gcc should be able to make the
decision to inline.
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch create debugfs file for IOST and add file operations.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch create debugfs file for DQ and add file operations
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch create debugfs file for CQ and add file operations.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch create debugfs file for port register and add file operations.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch create debugfs file for global register and add file
operations.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch takes snapshot for global regs, port regs, CQ, DQ, IOST, ITCT.

Add code for snapshot trig and generate dump directory.
Signed-off-by: NLuo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: NJohn Garry <john.garry@huawei.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>