trivial fix to spelling mistakes in wl1271_warning error message, change
iligal to invalid and opperation to operation.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

When resetting the device, we take a synchronous firmware-loading code
path, which borrows a lot from the asynchronous path used at probe time.
We don't catch errors correctly though, which means that in the PCIe
driver, we may try to dereference the 'adapter' struct after
mwifiex_fw_dpc() has freed it. See this (erronous) print in
mwifiex_pcie_reset_notify():

	mwifiex_dbg(adapter, INFO, "%s, successful\n", __func__);

Let's instead refactor the synchronous (or "!req_fw_nowait") path so
that we propagate errors and handle them properly.

This fixes a use-after-free issue in the PCIe driver, as well as a
misleading debug message ("successful"). It looks like the SDIO driver
doesn't have these problems, since it doesn't do anything after
mwifiex_reinit_sw().

Fixes: 4c5dae59 ("mwifiex: add PCIe function level reset support")
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If we fail to reinit the FW when resetting the device (in the
synchronous version of mwifiex_init_hw_fw() -> mwifiex_fw_dpc()),
mwifiex_fw_dpc() will tear down the interface and free up the adapter.
But we don't actually check for all failure cases of mwifiex_fw_dpc(),
so some of them fall through and dereference adapter->fw_done with a
freed adapter, causing a use-after-free bug.

In any case, mwifiex_fw_dpc() will always signal FW completion -- in the
error OR success case -- so at best, this was repeat work. Let's not do
it.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In brcmf_pno_start_sched_scan() a local variable is declared and
assigned for struct brcmu_d11inf. However, there is no other reference
to it so it is unnecessary.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

In brcmf_pcie_suspend() we inform the firmware on the device that
it will enter in D3 state. Before this is done we already bring down
the bus state. However, When entering D3 fails we abort the suspend
and the bus state need to be restored.
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To support network namespace the driver must assure all created
network interfaces are in the same namespace as the wiphy instance
and flag the support using WIPHY_FLAG_NETNS_OK.

Verified using two terminals:

 Terminal 1			Terminal 2
 --------------------------	---------------------------------
 # ip netns add brcm-wifi	# iw dev
				phy#0
					Interface wlan3
						ifindex 11
						wdev 0x1
 # ip netns exec brcm-wifi bash
 # iw dev
 # echo $$
 20337			# iw phy0 set netns 20337
 # iw dev
 phy#0
	Interface wlan3
		ifindex 11
		wdev 0x2
 # iw phy0 interface add wl3.ap type __ap
 # iw dev
 phy#0
	Interface wl3.ap
		ifindex 2
		wdev 0x3
	Interface wlan3
		ifindex 11
		wdev 0x2
				# iw dev
 # iw phy0 set netns 1
 # iw dev
				# iw dev
				phy#0
					Interface wl3.ap
						ifindex 2
						wdev 0x5
					Interface wlan3
						ifindex 11
						wdev 0x4

Note:
	increasing wdev identifier above indicates issue in
	cfg80211 which is addressed separately.
Tested-by: NMark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NHante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Move brcmf_fws_deinit into brcmf_proto_bcdc_detach since it is a bcdc
exclusive feature.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol layer interface brcmf_proto_init_cb for protocol
layer to finish initialzation after core module components(fweh and
etc.) are initialized.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Chip goes into low power state when this feature is enabled.
This was already enabled for SDIO and PCIe interface based
chipsets.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

USB firmware added support for sending command response/event through
interrupt endpoint, to enhance RX throughput. Added corresponding changes
required to support this feature. This change takes care of backward
compatibility with older firmware.
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

For quite some time now brcmfmac supports 802.11ac chipsets and it's
not limited to embedded devices only. There are even standalone PCIe
cards based on BCM43602 or BCM4366.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Reviewed-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

ath.git patches for 4.12. Major changes:

ath10k

* improve firmware download time for QCA6174 and QCA9377, especially
  helps resume time

ath9k_htc

* add support AirTies 1eda:2315 AR9271 device

Basic support for MT7620 built-in wireless radio was added to
OpenWrt in r41441. It has seen some heavy cleaning and refactoring
since in order to match the Kernel's code quality standards.
Signed-off-by: NRoman Yeryomin <roman@advem.lv>
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Make sure to check the number of endpoints to avoid dereferencing a
NULL-pointer or accessing memory beyond the endpoint array should a
malicious device lack the expected endpoints.

Fixes: a1030e92 ("[PATCH] zd1211rw: Convert installer CDROM device into WLAN device")
Cc: Daniel Drake <dsd@gentoo.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Some of the macros used to describe the TX_PWR_CFG_4 register accidentally
refer to TX_PWR_CFG_3, probably a copy&paste error. Fix that.
Signed-off-by: NDaniel Golle <daniel@makrotopia.org>
Acked-by: NStanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The check for rc < 0 is always false so the check is redundant
and can be removed.

Detected with CoverityScan, CID#101143 ("Logically dead code")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol interface function brcmf_proto_reset_if for core
module to notify protocol layer when interface role changes.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Create a new protocol interface function brcmf_proto_del_if for core
module to notify protocol layer upon interface deletion.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

fwsignal is only used by bcdc. Create a new protocol interface function
brcmf_proto_add_if for core module to notify protocol layer upon a new
interface is created.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmf_txcomplete is invoked by sdio and usb bus module which are using
bcdc protocol. So move it from core module into bcdc layer.
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

brcmf_txflowblock is invoked by sdio and usb bus module which are using
bcdc protocol. This patch makes it a bcdc API instead of a core module
function.
Reviewed-by: NArend Van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NFranky Lin <franky.lin@broadcom.com>
Signed-off-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

If a scan gets aborted BRCMF_SCAN_STATUS_BUSY gets cleared in
cfg->scan_status and when we receive an abort event from the firmware
the BRCMF_SCAN_STATUS_BUSY check in the cfg80211_escan_handler will
trigger resulting in multiple errors getting logged.

Check for a status of BRCMF_E_STATUS_ABORT and in this case simply
cleanly exit the cfg80211_escan_handler. This also avoids a
BRCMF_E_STATUS_ABORT event arriving after a new scan has been started
causing the new scan to complete prematurely without any data.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The country code gets set to "00" by default at boot, ignore this
rather then logging an error about it.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Using pr_err for things which are not errors is a bad idea. E.g. it
will cause the plymouth bootsplash screen to drop back to the text
console so that the user can see the error, which is not what we
normally want to happen.

Instead add a new brcmf_info macro and use that.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NArend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far we were attaching BRCMF_E_PSM_WATCHDOG event listener in
brcmf_debug_attach which gets compiled only with CONFIG_BRCMDBG. This
event means something went wrong and firmware / hardware usually can't
be expected to work (reliably).

Such a problem is significant for user experience so I believe we should
print an error unconditionally (even with debugging disabled). What can
be indeed optional is dumping bus memory as this is clearly part of
debugging process.

In the future we may also try to extend this listener by trying to
recover from the error or at least signal it to the cfg80211.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

PCI devices can be described in DT as well so we should always execute
relevant code. This will make bcma e.g. set of_node for cores described
in DT.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A tiny code deduplication thanks to the bcma_bus_get_host_dev.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We already have the same check in bcma_of_get_irq which really calls
symbols available with CONFIG_OF_IRQ only. It appears this duplicated
check was accidentally added in commit c58d900c ("bcma: fix building
without OF_IRQ"). The rest of code in bcma_of_fill_device should work
fine without CONFIG_OF_IRQ.
Signed-off-by: NRafał Miłecki <rafal@milecki.pl>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Two additional preset responses are added to the reserved page on the
wifi device.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Changes in the drivers for RTL8723BE and RTL8821AE require corresponding
changes in the firmware. This new firmware has been accepted into the
Linux firmware repo. To handle the case where the kernel has been
updated before the firmware, the new versions have been given new names.
The code will attempt to read the new name, and fall back to the old one
if the new one is not available.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Update PHY tables for the RTL8812AE. A new parser is also needed.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are new PHY table values for the RTL8821AE. The changes require
new parsing code.
Signed-off-by: NPing-Ke Shih <pkshih@realtek.com>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We observed a SHUTDOWN command timeout during reboot stress test due to
a corner case firmware bug. It can lead to either a use-after-free +
OOPS (on either the adapter structure, or the 'card' structure) or an
abort (where, e.g., the PCI device is "disabled" before we're done
dumping the FW).

We can avoid this by canceling/flushing the FW dump work:

(a) after we've terminated all other work queues (e.g., for processing
    commands which could time out)
(b) after we've disabled all interrupts (which could also queue more
    work for us)
(c) after we've unregistered the netdev and wiphy structures (and
    implicitly, and debugfs entries which could manually trigger FW dumps)
(d) before we've actually disabled the device (e.g.,
    pci_device_disable())

Altogether, this means no card->work will be scheduled if we sync at
a point that satisfies the above. This can be done at the beginning of
the .cleanup_if() callback.
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Application triggers periodic background scans when device is connected.
We will scan less number of channels per scan command so that data
traffic won't get affected.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Using the accessor function e.g. get_unaligned_le32 instead of
le32_to_cpu to avoid the unaligned access. This is for the
architectures that don't handle the unaligned memory access
Signed-off-by: NDevidas Puranik <devidas@marvell.com>
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Synopsys' ARCompact architecture does not support loading from or
storing values to unaligned memory locations. We saw a series of
misaligned access exceptions on ARC. To work around this issue, we bulk
replaced le16_to_cpu and le32_to_cpu with get_unaligned_le16 and
get_unaligned_le32, respectively. We also added le16_unaligned_add_cpu
which is similar to le16_add_cpu but works with unaligned values.
Signed-off-by: NDaniel Mentz <danielmentz@google.com>
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Adding qualifier "__packed" indicates that no padding should be
performed on the qualified object for alignment.
This patch adds qualifier __packed to the required firmware
structures in mwifiex driver.
Signed-off-by: NKarthik Ananthapadmanabha <karthida@marvell.com>
Signed-off-by: NGanapathi Bhat <gbhat@marvell.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

We shouldn't be printing a kernel pointer as a decimal integer. But we
really shouldn't be printing this case at all; we should never get here
with NULL drvdata. We've eliminated this unnecessary conditional in
several other places, so kill it here too.

Similarly, there's no need to check for '!pdev'; we are guaranteed to
have a real device here.

And finally, use dev_err() instead of pr_err().

This yields (for failed PCIe resets):

[   68.286586] mwifiex_pcie 0000:01:00.0: mwifiex_pcie_reset_notify: adapter structure is not valid

instead of:

[   82.932658] mwifiex_pcie: mwifiex_pcie_reset_notify: Card or adapter structure is not valid (-270880688088)
Signed-off-by: NBrian Norris <briannorris@chromium.org>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Currrently we are disabling this wake irq after receiving it. If this
happens before we finish suspend and the pm event check is disabled,
the system will continue suspending, and this irq would not work again.

We may need to abort system suspend to avoid that.
Signed-off-by: NJeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

last_qual never really holds a time. It only holds jiffies. Make it the
same type as jiffies.
Signed-off-by: NAlexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>