Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

mxc_nand driver must support the RESET Command in order to support
Micron NAND which need a reset before any other command.
Signed-off-by: NEric Benard <eric@eukrea.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The clock must already be off after mtd->suspend.  Disabling it again
results in an negative overflow of the clock usage count.  This didn't
hurt as mxcnd_resume undid it after wake up.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The probe function calls platform_set_drvdata with a valid pointer when
the probe is successful.  As mxcnd_suspend and mxcnd_resume are only
called on bound devices, platform_get_drvdata always returns non-NULL.

This fix isn't critical as the pointer is always valid so it doesn't
matter if the compiler generated code for it or not.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: NDavid Binderman <dcb314@hotmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This reverts commit 82613b0d, because
commit daa0f15a (mtd: don't use __exit_p to wrap mxcnd_remove) is a
better solution. Not having a remove callback breaks rebinding because
resources are not freed on remove.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The function mxcnd_remove is defined using __devexit, so don't use
__exit_p but __devexit_p to wrap it.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

wait_op_done is only called with the same timeout, so
code the timeout into the function itself.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The v2 version of this controller is used on i.MX35/25 SoCs.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Later versions of this controller also allow 4k pagesize,
so use mtd->writesize instead of a flag.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The main/spare areas are on different addresses on later versions
of the controller, so make them configurable.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Instead of having two switch/case with other operations
in between, use only one switch/case
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The NAND controller has some limitations how to access the
internal buffers. It only allows 32 bit accesses. The driver
used to work around this by having special alignment aware
copy routines.
We now copy the whole page to a buffer in memory and let the
access functions use this buffer. This simplifies the driver.
A bonnie++ test showed that this has no negative performance
impact on the driver.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This factors the address cycle to a seperate function. This
becomes useful in a later patch where we can simplify the
command processing by making use of this function.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The oob layout was initialized several times. Instead, use
a smallpage layout by default and switch to a largepage
afterwards if necessary.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

The original Freescale driver used to have eccoob descriptions like
this:

static struct nand_ecclayout nand_hw_eccoob_8 = {
	.eccbytes = 5,
	.eccpos = {6, 7, 8, 9, 10},
	.oobfree = {{0, 5}, {11, 5}}
};

static struct nand_ecclayout nand_hw_eccoob_16 = {
	.eccbytes = 5,
	.eccpos = {6, 7, 8, 9, 10},
	.oobfree = {{0, 6}, {12, 4}}
};

The former was used for 8bit flashes and the latter for 16bit flashes.
They honored the fact that the bad block marker on 8bit flashes is on byte 5
while on 16bit flashes it is on byte 11.
In the Kernel driver this was copied wrong and we ended up with two identical
descriptions.

Change it so that we have only one description which leaves byte 5 and byte
11 unspecified so that it won't be used by others.

Also, rename the descriptions to nand_hw_eccoob_smallpage and
nand_hw_eccoob_largepage so that it can't be confused with Nand chip bus
widths (what actually happened in this driver)
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This reverts commit 71b7d0d9.

The problem which that commit attempted to fix was a bootloader issue,
which had been misunderstood. The 'fix' causes lots of false bad blocks
for existing users with sane firmware.

Thanks to Mathieu Berland for diagnosing the problem coherently.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The function mxcnd_remove is used only wrapped by __exit_p so define it
using __exit.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: NSam Ravnborg <sam@ravnborg.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Vladimir Barinov <vova.barinov@gmail.com>
Cc: Vladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

This patch allows i.MX27 to support 2KiB pagesize NAND flash.
We are using a 1.8V NAND flash which datasheet (unfortunately only
available under NDA) says :
Page size: x8: 2,112 bytes (2,048 + 64 bytes).
Without this patch, all sectors are marked as bad eraseblock.
Signed-off-by: NEric Benard <ebenard@eukrea.com>
Acked-by : Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

with `while (max_retries-- > 0)' max_retries reaches -1 after the loop.
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

- Add support for 2KiB page size flashes
- Fix page address access for large pages
- Detect oob layout at runtime
- handle pagesize_2k variable
- Fix oob16 layout: reserve location 5 of oob area since it's used for bbt
Signed-off-by: NVladimir Barinov <vova.barinov@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Make sure to pass the same dev_id data to free_irq() that was
used when calling request_irq(), otherwise we get a warning about
freeing an already free IRQ.
Signed-off-by: NMagnus Lilja <lilja.magnus@gmail.com>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The following patch fixes:
 - re-initialization of host->col_addr which is used as byte index
   between the successive READID flash commands.
 - compile error when CONFIG_PM is enabled
 - pass on the error code from clk_get()
 - return -ENOMEM in case of failed ioremap()
 - pass on the return value of platform_driver_probe() directly
 - remove excessive printk
 - let command line partition table parsing with mxc_nand name.
   The cmd_line parsing is done via <mtd-id> name that differs
   from mxc_nand by default and looks like "NAND 256MiB 1,8V 8-bit"
Signed-off-by: NVladimir Barinov <vbarinov@embeddedalley.com>
Signed-off-by: NLothar Wassmann <LW@KARO-electronics.de>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Now the MTD core will do this for us, we don't need to hook it up from
the board drivers.

Shame we can't do shutdown from the class too...
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

Follow-on patch to the previous driver model patch for the MTD
framework.  This one makes various MTD drivers connect to the
driver model tree, so /sys/devices/virtual/mtd/* nodes are no
longer present ... mostly drivers used on boards I have handy.

Based on a patch from Kay Sievers.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>

The context makes it clear already that these are clocks, so there's
no need for such a suffix. This patch only changes the clocks actually
used in the tree. The remaining clocks are renamed in the subsequent
architecture specific patches.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

This patch adds support for the integrated NAND flash controller of the
i.MX2 and i.MX3 family. It is tested on MX27 but should work on MX3
aswell.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NJuergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>