GMAC has better performance and fewer hardware issues.
Use the GMAC in MII mode for ethernet instead of the EMAC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubieboard2 uses both the i2c0 and i2c1 controllers. Enable them in
the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubieboard2, just like its A10 counterpart, has the Ethernet wired
in. Enable it in the DT.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The Cubieboard2 is the successor of the first Cubieboard, and shares the
same hardware, except that the Allwinner A10 found initially has been
replaced by an Allwinner A20.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A20-olinuxino Micro has a LED connected to the PH2 pin. Use the
gpio-led driver to enable the control over this LED.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Instead of relying on the bootloader to mux the UART pins properly, do
it on our own and register the rightful pins for the A20-olinuxino in
the DT using pinctrl.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Olimex A20-Olinuxino is an open-hardware board based on the
Allwinner A20 SoC, with most of the pins exported on headers, a 10/100M
ethernet port, SATA, SD and uSD slots, etc.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This platform from WITS is the evaluation board for the Allwinner A31.
It features a quad-Cortex A7, 2048MB of RAM, NAND, USB, MMC, several
UART, HDMI, a 2048 x 1536 10" screen, powered by a PowerVR, etc.

Of course, most of these peripherals aren't supported yet, but support
for those will come eventually.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

There was a typo in the base address used for the soc node in the A10
device tree. Fix it with the proper base address.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Commit b00adbe0 ("ARM: sunxi: Rename uart nodes to serial") changed the
node names in the DTSI, changes that were not accordingly made to the
Mini X-Plus device tree. This breakage slipped through because it was
not properly declared in the Makefile.

Fix both issues.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This board comes with an Allwinner A10, two external USB ports, a SD
Card reader, 1GB of RAM, the usual video connectors and an onboard wifi
chip.

Of course, the support is quite minimal for now...
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This is the rename portion of "ARM: sunxi: Change device tree naming
scheme for sunxi" that were missed when the patch was applied.
Signed-off-by: NOlof Johansson <olof@lixom.net>

There is several different SoCs sharing the sun5i codename: A10s, A12
and A13. Since there is enough differences to not consider those the
same SoCs, change a bit the naming scheme to reflect this.

Moreover, some boards like the olinuxino come in A10s and A13 variants,
which also share the same SoC codename.

So change the naming scheme to reflect both the codename and the market
name of the SoCs used in the dtsi and in the board files
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

For the new sun4i/Cubieboard (A10) support, lets re-strucure the
sun5i dts files to make it more generic. Those are the new
dts/dtsi files:

sunxi.dtsi - Devices common to all Allwinner sunXi SoC's
sun4i.dtsi - sun4i Devices, will include sunxi.dtsi
sun5i.dtsi - sun5i Devices, will include sunxi.dtsi
board.dts - will include either sun4i.dtsi or sun5i.dtsi

Additionally the "duart" label in the olinuxino.dts is changed to
"uart1".
Signed-off-by: NStefan Roese <sr@denx.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The headers that are only used by board files do not necessarily
need to be in plat-mxc/include/mach.  Move them to the same place
as those board files.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NArnd Bergmann <arnd@arndb.de>

Change mxc_expio_init interface a little bit to have gpio than irq
number passed in.  With the change, gpio_to_irq can be called inside
mxc_expio_init to get irq number, so that MXC_IRQ_TO_GPIO can be
removed.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>

The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: NJason Wang <jason77.wang@gmail.com>
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>

Makes it consistent with VMALLOC_START
Tested-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NAndreas Fenkart <andreas.fenkart@streamunlimited.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Shared (platform) headers
Signed-off-by: Ndmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>